On the assumption you are, just climb in the loft and drag the cable over, it's not that bad, I've been in and out of lofts since my early teens doing house re-wires with my father and never put my foot through a ceiling.
Some of the old insulation will make you itchy as hell and probably not something you want to breathe but otherwise yeah, it's just a chore its not difficult assuming you are able bodied (I'm UK so our houses (until recently) had heavy duty joists so you can just clamber around on them, if gonna me up a while take a board up and lay it over a few to kneel/lay on and that's about it.
(I wouldn't be surprised if there was a mouse poop factor along for the ride after long enough, though)
The reason fiberglass is itchy is because it’s piercing the epidermis. It’s basically a pad of brittle micro hypodermic needles. Add those two together, and it gets extra fun.
Unless you're mobility limited, everything in an attic should be accessible.
The main considerations are:
- Do work when it's cold outside. Do not be up there when it's warm and sunny
- Wear a breathing mask. N95 / painter's mask works fine. Glass insulation particles aren't lethal, but also aren't stuff you want in lungs
- Think twice. Then move. Slowly. And feel you're standing on something stable before fully transferring your weight
- Mind your head. The roof plywood will likely have roofing nails sticking through
- Bring 2 lights, preferably one lantern-type. That way you can leave one en route
If it's blown insulation, you can sweep it over and expose joists to stand on.They're regularly spaced from the exterior wall to an interior beam, all running the same direction, and the support boards up to the roof will run down to one.
I wired a string of LED lights for a friend (with outlets), but I figured the electronics in them would eventually fry.
I wouldn't be surprised if attics in the southeast get up to 140F in the summer.
Rope lighting would be cheap and semi-insulated.
Re: the sibling's suggestion of wifi: If your cabling works at 100, I think the case is pretty clear for wired 100 vs wifi; consistent 100m is better than variable whatever you get. At 10m, not so clear, especially since cabling that's that old is also likely to be daisy chained, so you're looking at maybe a daisy chain of switches running at 10m. That said, cabling is often better than the spec it was tested to, and ethernet cable requirements are for long runs in dense conduit; it's worth trying 100M on old telephone wiring if it's already in the wall to see what you can get.
Would I want to use it to transfer large files around internally nowadays? No.
Works for everything else assuming you are the only user of that cable in that corner basement room? Absolutely.
Also insert appropriate "kids these days" joke. I guess it's like HD. Once you have it, you are not going back. Do I need a triple A game I just bought and want to play to download in 2 minutes vs 2 hours? No. But kids these days expect it I guess. No patience.
Or maybe they want to stream UHD content?
Let's not even talk about how miserable it would be to download modern games over this.
2. The idea in the comment is streaming at original bluray quality. Not transferring.
Also, I stream actual blu-ray rips over my network all the time, not just transferring them.
On a 120" display?
My office is in the basement corner with the sump pump, and said pump is located inside an undersized closet along with some pipework for the furnace, and all that like I said is in the very most corner space of the basement, basically inside a drywall box about 3 feet square. All things considered, it looks pretty nice. However I wanted ethernet back here for obvious reasons, and for several other reasons relating to layout, using either of the basement-facing walls wouldn't work.
SO: I realized that to run the plumbing and such from the furnace and utility area to this corner, they left a cavity a few inches tall in the ceiling at the outside-facing wall to this little cabinet. I bought a piece of 10-foot PVC pipe an inch wide, and slid it into this cavity between the existing pipes, securing it in place with a little bracket and some junk screws. Then I shoved four ethernet cables through that, into this little closet, and installed an ethernet wall plate in the door since it isn't regularly used and hooked it up there with enough slack that the door can move easily when we need to have any mechanicals serviced in there.
It's worked perfectly for the last 5 years. Love it.
So keep an eye out for a neighbor who has an electrician doing work and maybe see how much to just move the cable.
Drones is overthinking it.
That reminds of an idea I had for an app and/or website. I'm never going to get the time to actually try to make this, so if anyone wants to feel free.
I've had small tasks I wanted done that would only take someone with the right skills and equipment a few minutes that I didn't want to DIY either because I lack the skills or I'd need to buy some equipment I don't have and would not get enough future use out of to justify the cost, but I also didn't want to pay for the minimum of 30 minutes or 1 hour of labor that many contractors and companies charge.
A good example is that there was a security light mounted on a pole on top of my garage. I wanted to remove the bulb, but it was screwed in tight enough that using one of those light bulb removers on a pole I could not get it to budge. I'm not agile enough to be willing to try to climb onto my garage roof.
The idea is that I'd list this task on the app, with how much I'd pay (probably $20 cash) and my neighborhood. Then handymen, roofers, electricians, etc., could check the app or site when they are out on a job site and it would show them such tasks that are near them.
So say some roofers are doing something for a neighbor. They could check the app, see that it's a quick $20 cash for one of them on their way home or on their lunch break to come over and spend a minute or two doing my task. I was in no hurry to remove the light bulb, so I would have no problem waiting until someone with a ladder and a few minutes to spare happened to be working in the area and be willing to make a quick easy $20.
They have expenses, fuel, insurance. Most charge $100 as a trip fee.
> They have expenses, fuel, insurance.
I think you missed important details in their post:
>> tasks I wanted done that would only take someone with the right skills and equipment a few minutes
>> tasks that are near them
The idea is, you're someone handy with equipment, and someone down the block wants lights installed. So you walk there with a couple tools on your hand, spend 5 minutes doing it, and earn (say) $20. Instead of just sitting at home and watching TV when you're bored. If you don't feel like it then you just don't take the offer up.
This is not meant to be an alternative to your day job. It's just intended to be something extra you can do when you're home anyway. If transportation and fuel and other costs would factor in then you just wouldn't do it.
It's in no way insulting, it's an opportunity for anyone that wants it. I'm not a handyman but I'd definitely do this from time to time if (say) my neighbors needed computer or coding help for a few minutes.
Coding a web page for a neighbour is different since there are often no ramifications in the physical world if it doesn’t load or look exactly as desired
(Beyond that, even if they’re already in the area, by the time they pull up the truck, load and unload the ladder and actually do the job, the per-minute rate is probably already a fair bit worse than what they would earn from real customers - it may seem to you like you’re offering an easy job at $10/minute, but it’s probably a tenth of that all in from their perspective.)
Although in an ideal scenario that’s a really great idea, as quite many people (I believe) may be in need of such services.
It's probably not worth it for anyone you might actually want to hire and doubly so for anything to which substantial chance of liability attaches. It might make more sense as a list of things your friends/neighbors/family could use help with playing up altruism angle and minimizing emphasise on liability. You know more like neighbor helping neighbor. You could also hopefully integrate positive things like sharing things that may still have value eg you upgraded your washing and dryer but the old set are still workable or things to do that others might want to share in so its not all a distributed version of your grandma's chore list.
Incidentally a have a great domain used for a fairly half-assed implementation of a not entirely different idea.
What ever happened to taskrabbit anyway?
Wheeled or tracked R/C cars are much easier to control, and can pull a greater force horizontally without losing control. In the 90s it was somewhat standard, especially in office environments with drop ceilings, to use a little 9.6v Tyco Fast Traxx to zip a pullstring across the ceiling grid, then use the string to pull the much heavier cables. (I'm not sure what's in use today, but I put a LOT of miles on that Tyco.)
Leave some slack at each end, sufficient to lift the cable up and place it in ceiling hangers "later", wink wink. Because leaving it flopped along the ceiling grid wasn't professional, nudge nudge.
Anyway, you don't splice in the middle. Neeeeever do that. Hidden splices are madness-inducing. If you need a mid-span location, you should be pulling all your runs from/to a closet and just use that as a distribution frame.
In your case, you could pull string from both ends, tie the strings together, then use the strings to pull a direct run of cable.
(Having that big rechargeable 9.6v battery came in handy other ways, too. There were plenty of times where I needed a talk path but only had a dry pair. Hook up the battery in the loop, with a butt-set or plain old beige phone at either end, et voila!)
To add on to the pull string.. if there is a remote chance you have to run a cable the same direction again in the future, try to leave a pull string in place when you pull all the cables initially.
In a commercial setting at least, it’s not up to code, let alone standards of good workmanship.
Instead of: "I took my $500k/year tech salary which I formerly spent on Teslas and cardboard apartments and just hired a competent electrician or other tradesman to pull cable to every room."
And before anyone adds on with 'lol pay more', they try. The people just aren't there.
Ergo, if they can, tradespeople take commercial jobs.
Which leaves residential tradesperson as something of a lemon market. (And I wouldn't want to put up with one-off job, haggling about payment, if I had commercial options)
Just finding a contractor or business owner able to think clearly is reaching near impossibility.
Like on even the most basic things. It’s quite concerning.
The breakdown of the apprentice model ~20 years ago and now-due generational consequences of that change seems more to blame.
Community expertise evaporated with retirement of folks who have been doing it 30+ years.
And without anyone receiving it... many of the folks out there are "let me look up plans at Home Depot before doing the job" types.
This fall is part of a steady escalation.
It appears to be heavily correlated with the insane propaganda floating around too.
I don't really understand people who pay others to do every little thing they need done around the house, but I suppose they have different values than I so live and let live...
Except the whole point of his post was that he didn't know how to do it competently, there's no way he wants to enter the crawlspace, so has resorted to wacky workarounds.
So, no, it clearly isn't within the skill (or desire) of anyone, but many would rather resort to hackery and hubris rather than pay someone to do it correctly.
I'll counter that and say there's probably minimum wage coders in India who write equal or better code than you at 1/10th of the pay, certainly possible as they have two functioning hands.
Worth it, though, and would do it again.
I realized that it is cheaper for me to pay someone do some things than doing them myself. Instead, I can either work or do something fun or more interesting.
I think that's the key point really. For someone with even a mild interest in this stuff, the task of running ethernet cables is very approachable and feasible. At that point the time spent on it is a plus instead of a minus, and paying someone else is no longer competitive.
A place I used to live had structured cabling built in and half of it was CCA. I could tell immediately when I cut the cable to terminate it just by seeing the silver ends. It even said CCA on the casing so wasn't even fake.
Electricians are definitely better than you at running cable and knowing where to cut the holes. But make sure you choose the cable and terminate it yourself.
You'd have to pay me that kind of money (amortized) to deal with vetting/hiring/managing/scheduling/QC'ing someone else and their work.
I've been dealing with twisted pair cable since the mid-90s and I've never seen Cat 4 cable anywhere, commercial or residential.
Cat 5/5e both support GigE. The primary difference between FE and GE with respect to cabling is that GE uses all 4 pairs where FE used only 2 pairs. The difference between 5 and 5e cable is pretty negligible, and the GigE standard only requires Cat 5, not 5e
With respect to Cat 4, you're confusing the signal bandwidth and data rate. Cat 4 supports up to 20 Mhz signal bandwidth. It can be utilized by either 10BASE-T (10 Mbit/s) or 100BASE-T4 (100 Mbit/s).
If there's twisted pair data cabling in the home at all, it's probably suitable for GigE. Otherwise it's likely RJ11 phone cabling that's not typically going to be in a home run topology.
That said, the standards are pretty forgiving over shorter distances. Here's someone claiming they got GigE speeds over Cat 3 cabling in an older home:
If you’re up there a lot or doing a lot of things, it’s also exhausting paying that much attention. And inevitably, you’ll screw up.
I am 45. Last year, before I moved to a new house, I decided to run CAT8 Ethernet everywhere. Some people told me that they consider this excessive, but compared to the cost of the house, the extra cost was negligible and I hope this network will do well into the 2050s.
That being said, I removed my EOP after I ungraded to Eero 6e's. The wireless backhaul was much faster than the wired at that point, and Eeros won't load balance between the two interfaces, so the hardwire was actually slowing things down.
Sure is handy when you need a cable and same-breaker sockets are nearby, though!
The most annoying is to go through fire blocks in the walls. Because this requires you to open up and patch the drywall at 1.5m height if you bring the cable from the attic. From the crawlspace the hardest part is to make sure you drill inside the wall, not through the floor! For that I found that somebody with a powerful magnet in the house while you carry metal washers with you under is helpful to locate precisely the walls. You can often see the nails holding the floor plate as well to fine tune the location.
I recommend a good respirator mask, and a jumpsuit to retain some psychological distance with the spiders.
I did some interior inspection with my Mini 2 in an area that was too small for me to crawl to.
I did get it to work, but it was a close thing. Air currents in tightly enclosed spaces do not play nicely with drone stability algorithms.
Also, if you have blown-in insulation, it will fly up and get stuck in your motors in a matter of seconds to minutes unless you can keep a ~6' standoff. FWIW.
Run them all over the damn places, anywhere you might want Ethernet or coax or HDMI or whatever is big ten years from now. You don't even need to pull the Ethernet now; just put blank covers on the boxes you don't need.
Once you have the tubes in all your walls, future cable pulls become a snap; you don't even need fish tape half the time, you can just push Ethernet in one side and have it pop out the other.
I ran coax RG6 and CAT5 to every room in my house 24 years ago. The CAT5 seems to run 1000Mb/s just fine.
It was a lot of work to install it, but the results have been well worth it.
(We just tape the string to the balls with a few loops of duct tape, though.)
But to answer your question: depending on distance, you can consider using rigid plastic conduit, and thread the cable using that through the crawlspace, assuming you have access at the origin and destination. This is how we thread cable through a ceiling without any crawl space (flat roof)
How old is the house? If its more than 20ish years old running coax everywhere was a great choice. That would be before CAT5e cable so if they had went with ethernet cable instead of coax you'd be looking at 100 Mb/s. If it was built before 1995 you'd be looking at CAT4 and under 20 Mb/s.
I've got an ethernet cable running between the two rooms that are farthest apart in my house, but it is kind of ugly. I just screwed in cup hooks or nailed in nails at an angle on the walls up near the ceiling and draped the cable over them.
The right way would be to run it through the crawlspace or attic. I don't want to crawl around in the crawlspace, and my attic is the kind that if you aren't very careful you can put a foot through the ceiling of the room below, and has a bunch of blown in insulation that would probably make it even harder to get around so I don't want to try that.
I've wondered if I could run cable through the attic without actually going into the attic. Open the top of a wall below and drill up into the attic. Attach the cable to a pole and use that to push it up into the attic several feet, with the end of the cable tied into a loop.
Then send a drone into the attic, fly it to the pole, hook the loop, detach the cable from the pole, and fly the end of the cable over to the attic access hatch.
Then do the same with a cable at the other end. Splice the two ends together.
Is that reasonable feasible or is it just crazy?