The rotating / reciprocating mass may appear stationary at some RPM.
Just a reminder to only ever use incandescent or halogen lights around machinery you can touch while in operation: drills, lathes, mills, slotting machines, etc.
Before you start a tool you should act out your planned motion. Then start the tool and only perform this motion. If something changes and you cannot complete the motion, stop the tool immediately. Following this and a few other safety tips I've operated power tools for years without incident and I'm legally blind.
Okay, but, say you've configured the tool wrong and now it's destroying your work. You stop the tool. How soon is it safe to grab your work away from the work surface—i.e. when will it go from "it's too dangerous, let it keep destroying the work" to "it's now slow enough to pull the work off of the tool while it's still—slowly—running, to save the work from further damage"? That's a thing you have to figure out with your eyes (and ears).
So, evidently, I may have over stated my initial claim about only using incandescent lights.
Still, it’s something to me conscious of.
Not saying it can't happen but it does seem stupidly hard to achieve.
Many AC motors are synchronized to the frequency of the power line, by the same principal that turbines in the power grid are. So 60hz AC often means 30hz = 1800 rpm motor, and 59.8hz AC means 29.9hz motor. So if you have LEDs with a half bridge rectifier and your machinery is 180 degree rotationally symmetric, it will appear to not be moving, even if the line frequency fluctuates.
Fluorescent tubes are most noticeable, LEDs a little less. Tungsten or Halogen are the only sensible option for workpiece illumination.
For my hobby stuff, I just bought a couple of spare halogens that should see me out.
If the light is flickering it's absolutely guaranteed that it's derived from this.
But it's hard to imagine a lightbulb that emits a short enough pulse of light to make something look stopped. Even an absolute garbage one-way rectifier will be emitting light more than a quarter of the time. That can make a tool look odd, but it won't make it look still.
Not necessarily. If it's a 50/60 or 100/120 Hz flicker then yes, but LED lights with a cheap switching power supply might still flicker at the switching frequency, which could be say 400Hz or something.
Even after 20 years in the metal fabrication industry that scenario still spooks me.
Most will flicker at a multiply of the power line frequency (60 or 50 Hz depending where you live).
It's so common, that most digital cameras have a setting to set the power line frequency, so they can reduce the flickering in the footage.
Incidentally - many alternating current engines are also working with multiples of the powerline frequency, because it's easier that way.
Edited to add: Have you ever heard of a timing light for an engine? This works exactly the way you are describing.
The timing light is then pointed at the flywheel on an engine, which has numbers or marks stamped into it. Each time the spark plug fires the timing light (which is hooked into that same current via induction) lights up for a brief amount of time to show at what timing offset the engine is currently at. (this all happens at hundreds of rpms a minute).
so I'm not sure it's the same
Never underestimate the ability of machinery to rapidly render you dead.
Never underestimate the ability of otherwise intelligent people to intentionally disable safeguards, or guninely make mistakes.
So far, the discussion sounds like it's a theoretical possibility. If it's a real possibility, then it's something that should have happened a number of times.
The rotation frequency would have to be close to a relatively simple multiple (or fraction) of AC frequency but the way electric motors are contstructed if the piece is directly connected to a motor it is very likely it is true.
Visible light impulses influence brain wave patterns (e.g. [1]), and it might not be beneficial to look at pulsed light with a frequency that is not well researched.
Same thing with screens, most LEDs are dimmed with pulse width modulation [2], so they flicker at most brightness levels except the very brightest one. Some iPhone X users claim they get a headache when looking at the phone at the lowest brightness setting (OLED is even worse in that regard than LED, IIRC).
1: https://clinicaltrials.gov/ct2/show/NCT03657745 2: https://www.eetimes.com/document.asp?doc_id=1281013
On iOS there’s a setting buried deeply in accessibility settings, I think it’s called white point correction.
And on iPhone XS this is even worst. I wonder if there are any solution to PWM problem.
The worst bulbs I've personally seen for flicker were dimmable ones.
The non-dimmable variant from the same range had no noticable flicker.
Price paid also seems to be no indicator of quality – I've had premium LED bulbs from major makes, bought from a reputable wholesaler, that have died after 6 months within days of each other.
I've had cheap no-name imports that have lasted years and had no flicker.
However, there are also LEDs that support legacy dimming, but again translate less current into different flicker patterns...
In other places I don't have dimmers but have low-voltage (12V) cans. Lots of flicker issues there too, presumably due to the 120->12V transformer at the can.
And then I have a light fixture that's both dimmed and a custom 12V setup. I've given up on finding a working dimmer/LED bulb (MR16 GU5.3) there. Probably need new 12V transformers?
Especially when my dog bounces around it looks like she is in a strobe light. I did a couple of videos of it just to "prove" it in some fashion.
――――――
This is slightly worrying.
The stroboscopic effect is really fun right until you're in a place with lots of moving parts at a multiple of the strobe frequency.
OTOH it's also used to fine-tune engine timing and such: set a stroboscope at a fraction of the frequency you want, the engine is properly tuned when everything looks completely stopped. Makes it very easy to notice mistiming.
I do some occasional wood-turning, but usually augmented with ambient daylight - along with the dubious safety advantage of having a very noisy electric motor.
Plus I'm old enough to have used a timing light hanging off a distributor on my first car. Try explaining that to the kids of today. ; )
The flicker is a thing from the past (or should be).
The CRT was a 17” running at 60hz. The rubber band sailed past in the span of about 2 screen refreshes, so it traveled that distance in 2/60 of a second. Distance was easy to calculate by the Pythagorean theorem or by holding a ruler to the screen, I forget which.
Here are two good sites that posted graphs of light intensity over time for a bunch of different bulbs: http://www.ledbenchmark.com/ http://sle.se/michael/led/ (Swedish)
Unfortunately, they both stopped updating around 2015. Anyone know of similar sources for more recent bulbs?
> “I am on a mission to make lighting healthy. That's why I made Bedtime Bulb: https://bedtimebulb.com/ It has the lowest flicker I've ever seen in a bulb form factor—even less than those claiming to be "flicker-free."”
In addition to that, a few other database sites that test for flicker were mentioned here³.
――――――
¹ — https://news.ycombinator.com/item?id=18644590
I don't have a database, but I can say that most (but not all) filament designs are terrible for flicker--ours is an exception. Philips products seem to have gotten worse in quality over time, probably to remain competitive, but they are better than the worst. Ikea's stuff is pretty good overall. I don't have a consistent recommendation for low-flicker general lighting right now, as every brand has good and bad products.
And, yeah, I tried that Soraa healthy bulb, and it was shockingly bad, given how it was advertised. Even the regular Soraa bulbs were disappointingly flickery, though less so. Also, just looking at the pattern it makes on my phone's rolling shutter, the wave is quite saw-toothed, and I wonder if that makes it worse? I have some Ikea candelabra bulbs which were always pleasant, and I was surprised to see they also left quite a visible flicker pattern on my phone, though much more sinusoidal/smoother.
It's a shame about the flicker in the Soraa bulbs, since the colors really did seem nice.
What's interesting is that the bulb seems to have a nice build quality (from the outside, I didn't open it) and is quite heavy. I suspect they are putting a BIG heatsink in there, as violet pump phosphors tend to degrade quickly.
The other thing that irks me about this product is the "zero blue" messaging. Yes, I can confirm the spectrum looks like what they are advertising, with a peak around 415nm, almost nothing between 440-490nm, and then all the rest of the colors from green to red.
But, green light is just as bad as blue for sleep! The ipRGCs are sensitive to both blue and green (up to around 600nm) This bulb has a lot of green, more than a lot of other light sources. It also has a very unpleasant greenish color (IMO) and low-ish CRI, around 78 on the bulb I tested.
Is it better than a normal 600lm bulb for sleep? Yes. Is it novel? Yes. Is it good in practice? I don't think so.
what does that mean? Duty cycle is 50%, frequency at something Hz? Not being snarky - curious whether there is some kind of standard that your tool compares against.
A duty cycle 50% (or any percent really) isn't bad in itself, it's the frequency that is the culprit. Too low PWM freq and you'll notice it.
Two factors are often used to describe flicker for lighting:
- Modulation %, a.k.a. % Flicker [The height or modulation of the waveform, formula is 100% * (A - B) / (A + B)]
- Frequency [self-explanatory]
Flicker Index is also used (refer to [1] page 7 for more info) but rarely.
Duty cycle is not considered relevant, as you mentioned.
Some tools designed to measure lighting, such as my UPRtek CV600 [2], spit out % flicker, frequency, and flicker index, in addition to a bunch of spectrophotometry metrics. It's also pretty easy to calculate the modulation % with an oscilloscope and photodiode, it's just Vp-p / Vmax.
IEEE 1789 [0][1] roughly says that the higher the flicker frequency, the more acceptable it is to have a high modulation %. If you look at the graphic on [1] page 18, you can see this relationship. The white area is considered unsafe, the yellow area is "low-risk", and the green area is "safe." I don't 100% agree with this personally, as most incandescent lighting, with around 6-11% flicker at 100-120 Hz, would fall into the unsafe or low-risk category. But the Soraa product is definitely in the unsafe category.
For reference, I plotted my product (Bedtime Bulb) against an incandescent A19, Lighting Science's Goodnight A19, and Soraa's Healthy A19 on an IEEE 1789 graphic [3] with a Python tool I'm developing, Beautiful Flicker [4]. You can see that this incandescent, measured around 10%, is on the border between unsafe and low-risk by this standard.
Hope this helps!
[0] IEEE 1789: A new standard for evaluating flickering LEDs?: https://www.dial.de/en/blog/article/ieee-1789-a-new-standard...
[1] Flicker: Understanding the New Recommended Practice (PDF) https://www.energy.gov/sites/prod/files/2015/05/f22/miller%2...
[2] UPRtek CV600 https://www.uprtek.com/en/product/SPECTRAL-COLOR-METER/CV600...
[3] IEEE 1789 Graphic Comparing 4 Light Sources https://github.com/yeutterg/beautiful-flicker/blob/master/ou...
[4] Beautiful Flicker https://github.com/yeutterg/beautiful-flicker
I saw a test in a Swedish newspaper lately that showed IKEA's cheapest lightbulbs as one of the less flickery ones in the test. IKEA art.nr 303.887.64. So much for the price to guide you.
LED lights are alright. Lots of people think that everything used to be better but my memory is too good to fall for that trap.
The switch-mode power supplies in proper lamps get the stuff done way better and there will be no noticeable flicker. Maybe in the order of several kHz in ripple which you cannot see.
Also; cheap off brands (looking at you china) sometimes have caps rated at 250V which is far from the peak mains rate of about 320V (in 220/230V countries).
[1] https://www.powerelectronictips.com/whats-stuff-capacitive-p...
* at least in the UK
I mean, it looks absolutely fine as long as the light source and viewer are both static - just a shame vehicles tend to be moving :(
Of course it's still hit or miss, compatibility between bulbs and dimmers seems to be very hard to judge without testing these days.
Most dimmers work via pulse width modulation [1], i.e. the power supply is switched on/off in a different interval (more off time means lower brightness). A true flicker-free dimmed LED has to be dimmed in an analog way (probably only feasible for "dumb" light bulbs). PWM of 20kHz or something might also work, but who knows what that does to brain waves.
1: https://www.waveformlighting.com/film-photography/an-introdu...
――――――
Do I need to buy a specific model of Philips bulbs? Or is my Ikea lamp the culprit now? I paid a ton of money for a certified flicker free monitor so I'm very keen on making sure the lamps are flicker free as well.
Through trial and error I found that 72hz was acceptable/ok and 90hz and above was great. Other folks generally didn't notice, but sometimes could if I showed them to look sideways etc. This must explain why I've never knowingly been bothered by 120hz LED flicker, it is below my ability to consciously notice.
Curious, I took a look at several bulbs, with the mobile at 240fps trick described elsewhere. A new Feit dimmable, new Ecosmart non, a several year old Ikea, and a no-name CFL. All showed flicker except the CFL. All the LEDs flickered, but the amplitude was larger on the ecosmart. Feit and Ikea had a small amplitude.
Perhaps they are putting half the LEDs out of phase to get the smaller amplitude, or they should?
Of course it's not the LEDs that do this but the cheap AC-DC conversion bridge rectifier.
Source: I just had a problem with a malfunctioning light switch (not even a dimming switch, a plain two-state switch) wherein sometimes it would poorly complete the circuit, and one bulb out of the four on the circuit would start oscillating on and off. (If you removed the one bulb, another would start. If you plugged the first bulb back in, in the original slot or another, it would happen to the first bulb only.)
Lights is something that I used to cheap out on but no more. Not buying Philips bulbs is definitely 'penny wise, pound foolish'.
Also, Philips Hue!
I film all the LED bulbs I buy in slow motion at 240 fps with an Android phone, and play the movie back on a PC with mplayer using the dot(".") key to move frame by frame. Here is a shot I made comparing 2 brands of LED bulbs: https://youtu.be/QbenId_F2RQ (Edit: yeah you don't have to transfer to a PC, just playing back in slow motion on the phone will still show the effect quite well.)
It's amazing how I find this way that most (but not all!) of LED bulbs flicker with a strobe effect at 120 Hz (frames alternate between bright and dim) because they have crappy power supply designs that fail to smooth the A/C voltage. As a result they flash one time during the positive phase and one time during the negative phase of the 60 Hz A/C mains frequency.
I find this unacceptable. Although not too noticeable in normal conditions, a 120 Hz strobing light is definitely noticeable when your eyes move or track an object illuminated by the bulb.
In my experience, Philips lightbulbs are one of the few brands that don't have this flaw because they take care of converting AC to a stable DC voltage internally. In fact they are advertised as such: https://www.amazon.com/dp/B07CFRCGKC "COMFORTABLE LIGHT: Our products meet strict test criteria including flicker, strobe, glare and color rendition to ensure they meet EyeComfort requirements"