News for hackers. Stuff that matters.
Re:US companies are producing heat pumps that work below -20... by brilee on Wednesday December 28, 2022 @09:59AM (#34161557)
I wrote up a brief discussion here on the boiling points of refrigerants https://www.moderndescartes.com/essays/refrigerants/

The long and short of it is that if the heat pump works below -20F, then the boiling point of the refrigerant must be below -20F. This, in turn, implies a higher pressurization (as per the Clausius-Clapeyron eq) required in order to achieve a T_hot of 80F (or whatever output temperature you want. The higher pressurizations require more expensive components and compressors.

Re:US companies are producing heat pumps that work below -20... by Scoundreller on Wednesday December 28, 2022 @10:17AM (#34161759)
Maybe I’m dumb, but aren’t compressors pressure-agnostic? They just add pressure, right?

Other than needing to be a bit stronger to keep from bursting against the higher delta with the ambient atmospheric pressure like the rest of the components.

Re:US companies are producing heat pumps that work below -20... by Cerium on Wednesday December 28, 2022 @10:36AM (#34162013)
In this case there is a higher delta between the system and the atmosphere as well as a higher delta between the hot and the cold side, which is what requires a stronger compressor.
Re:US companies are producing heat pumps that work below -20... by Gibbon1 on Wednesday December 28, 2022 @02:29PM (#34164818)
I had a HVAC guy mention that seals are problematic always with non hermetic compressors. Everything larger than a fractional HP system has a shaft seal between the compressor and the motor. Small systems being a pain because there is less refrigerant and no way to monitor the amount.
Re:US companies are producing heat pumps that work below -20... by warmwaffles on Wednesday December 28, 2022 @03:58PM (#34165858)
There is a way to monitor it, but you'd need to put in T-Junctions and add a pressure sensor on the high and low pressure sides. You'd then need to rig up some system to read those pressures. But _you_ would be unfortunately the one that has to do it because I don't think there are any off the shelf solutions.
Re:US companies are producing heat pumps that work below -20... by mindslight on Wednesday December 28, 2022 @10:37AM (#34162021)
The ideal model of everything is everything-agnostic.

Refrigeration stuff is generally soft copper, and modern refrigerants are already working up in the hundreds of PSI. So I can see that getting expensive or requiring a sea change in materials.

Re:US companies are producing heat pumps that work below -20... by eloff on Wednesday December 28, 2022 @11:25AM (#34162548)
If they’re using copper, changing materials would probably save money. Copper is comparatively expensive. I suspect your premise that they are using mostly copper is incorrect, but then I write software for a living, what do I know.
Re:US companies are producing heat pumps that work below -20... by loeg on Wednesday December 28, 2022 @11:44AM (#34162792)
Copper is (very) effective for conducting heat. Aluminum is also pretty effective but obviously has different material properties than copper. It might be a good fit here; I don't work in the space.
Re:US companies are producing heat pumps that work below -20... by bluGill on Wednesday December 28, 2022 @12:17PM (#34163220)
Aluminum generally has fatigue limits that mean it will fail eventually, releasing refrigerant (which is normally an environmental disaster)
Re:US companies are producing heat pumps that work below -20... by dashundchen on Wednesday December 28, 2022 @12:42PM (#34163540)
The newer refrigeratants that require higher pressures are much better for ozone and have a lower global warming potential.

Pentane and isopentane, R601 being one of them (of course flammability is a problem) and R744 which is just CO2.

Re:US companies are producing heat pumps that work below -20... by dylan604 on Wednesday December 28, 2022 @12:39PM (#34163497)
what qualifies as a disaster? the amount of refrigerant in a consumer unit just doesn't seem like a lot even if 100% of it was released. if it was a continuous supply, then maybe it could get disaster level, but these are closed systems with a finite amount. at these levels, it seems to me that just driving one's car would qualify as an environmental disaster.
Re:US companies are producing heat pumps that work below -20... by Retric on Wednesday December 28, 2022 @01:36PM (#34164125)
The issue isn’t just the 1st one that breaks the issue is the 100,000+ that do.
Re:US companies are producing heat pumps that work below -20... by adonovan on Wednesday December 28, 2022 @02:26PM (#34164777)
If a typical large split system has about 10Kg of R410A (GWP = 2000x CO2) that's about 20 metric tonnes of CO2. Compare to 5 tonnes for an average passenger car per year. So a leak is like four years of driving a car.

Is it a disaster when an invisible odorless gas escapes and no-one notices? Or when a tree falls in forest? Not on its own, but our entire crisis is a pile of sand grains each too small to count.

Re:US companies are producing heat pumps that work below -20... by dylan604 on Wednesday December 28, 2022 @02:30PM (#34164838)
My real point was accident vs disaster. Whether anyone knows about it or not (someone will know when the AC doesn't work and the repair tech sees it being empty). If one house looses coolant, then I'd call it an accident. If a vendor has a major problem during manufacturing so that the majority of units fail, then maybe we can use bigger words.
Re:US companies are producing heat pumps that work below -20... by kazen44 on Wednesday December 28, 2022 @12:51PM (#34163656)
aluminium also has the problem that it is a dissimaler enough metal from most other plumbing hardware (being either made of brass, copper or steel) that it will result in the buildup of a lot of gunk because the aluminium disolves.
Re:US companies are producing heat pumps that work below -20... by eloff on Wednesday December 28, 2022 @05:15PM (#34166747)
That’s galvanic corrosion, but it’s usually an issue in water. I don’t know that it would be a problem with refrigerants, likely not.
Re:US companies are producing heat pumps that work below -20... by pjc50 on Wednesday December 28, 2022 @11:53AM (#34162904)
Copper has long been the choice for piping because it's soft enough to bend without cracking. The obvious #2 choice, stainless steel, is often even more expensive.

(I don't like the standard HN analysis technique of assuming that another field has made a really basic error that can be spotted by an autodidact from outside)

Re:US companies are producing heat pumps that work below -20... by etrautmann on Wednesday December 28, 2022 @02:22PM (#34164737)
While I generally agree with your response to the perceived arrogance - shouldn’t we all ask if we can do better than assuming someone else is an expert and has fully optimized a solution? As long as we approach new domains with a sense of humility and respect I think it’s desirable to always be looking for better solutions.
Re:US companies are producing heat pumps that work below -20... by mindslight on Wednesday December 28, 2022 @03:52PM (#34165805)
> assuming someone else is an expert and has fully optimized a solution?

I wasn't offering my own singular expert [0] opinion, but rather pointing out what I've observed the entire industry has seemingly converged on. Despite being subject to the hyper-cost-optimization of the consumer market, every refrigeration appliance I've seen still uses copper heat exchanger tubes and copper piping.

I would welcome someone chiming in saying something like "actually I work in HVAC and things are moving towards aluminum heat exchanger tubes and stainless piping, because I'd learn something new. But "just asking questions" based on one material property isn't particularly helpful.

And yeah, copper has gotten expensive. That has helped some new technologies displace it (eg PEX), but it's also still used where it's needed (eg PEX fittings over 1" nominal (which is equivalent to 3/4 copper) are prohibitively expensive for some reason).

[0] In fact, I'm not a refrigeration professional, and have yet to pretend to be one. I just tend to look at how things are built.

Re:US companies are producing heat pumps that work below -20... by eloff on Wednesday December 28, 2022 @04:17PM (#34166079)
First off, I was upfront about my ignorance. Secondly, copper is way more expensive than stainless steel, unless I’m missing something. More than 8x according to random websites on Google.

I’m sure there is a reason copper is used, but if the industry has to find an alternative, it would likely be cheaper.

Re:US companies are producing heat pumps that work below -20... by mindslight on Wednesday December 28, 2022 @05:25PM (#34166859)
Stainless sucks at heat transfer, and has to be welded. Copper can be soldered (low temperature), or I believe refrigeration lines are commonly brazed (higher temperature).

Material cost doesn't tell the whole story. Stainless is harder to work with, therefore costs more to manufacture. And even if it ended up being less expensive in the long run, there would a lot of capital equipment to recover.

Re:US companies are producing heat pumps that work below -20... by Kirby64 on Wednesday December 28, 2022 @09:41PM (#34168826)
Stainless steel not conducting heat would be an advantage for linesets - you don't really want the heat/cold to be released in the lineset... it's released in the condenser/evap coils. Those coils are already often made out of aluminum, so dissimilar metals aren't really an issue as far as I can tell...
Re:US companies are producing heat pumps that work below -20... by lazide on Wednesday December 28, 2022 @11:10PM (#34169444)
Flexible stainless tubing is more expensive than copper flexible tubing.

Also, copper flexible tubing is super easy to source.

Re:US companies are producing heat pumps that work below -20... by jasonwatkinspdx on Wednesday December 28, 2022 @05:36PM (#34166976)
FWIW there does seem to be a certain blind spot about PEX as an alternative in the US.

A friend redid his whole house with it himself to great success. He mentioned one of the contractors he got a bid from while deciding his plan, when asked about PEX, said "Well that just saves you time and money" in tone of dismissal.

I think there's something similar going on with ductless heat pumps in the US. They're a fantastic option in my area but still uncommon. Part of that seems to be the installers make more from other options.

I very much agree with you about the tendency of HN's community to assume other industries are simply obvious idiots, rather than realizing they're just ignorant of that industry's reality.

Re:US companies are producing heat pumps that work below -20... by lazide on Wednesday December 28, 2022 @11:09PM (#34169440)
Personally, having lived in places with ductless heat pumps they suck.

Lots more maintenance (they need regular cleaning or they build up mold), they don’t circulate air through the house so rooms get their own weird microclimates and get stuffier, and it’s a constant hassle tracking down remotes.

Central is way more comfortable and lower maintenance, IMO.

Re:US companies are producing heat pumps that work below -20... by Marsymars on Thursday December 29, 2022 @03:41PM (#34177644)
My house with central forced air already has rooms with weird microclimates due to differing amounts of exterior walls and/or windows. I’ve had the thought that I could use ductless heat pumps to reduce the temperature differences between different rooms in my house.
Re:US companies are producing heat pumps that work below -20... by SnowHill9902 on Wednesday December 28, 2022 @10:55AM (#34162211)
Power for compressible fluids is approximately proportional to the relation of pressures not difference.
Re:US companies are producing heat pumps that work below -20... by zip1234 on Wednesday December 28, 2022 @11:37AM (#34162699)
Even if you do need to make thicker pipes, strength in a metal generally increases with the square of the thickness, so it doesn't cost twice as much in materials to double the strength.
Re:US companies are producing heat pumps that work below -20... by londons_explore on Wednesday December 28, 2022 @12:14PM (#34163183)
This isn't true. For pipes, double the pressure requires double the wall thickness, which requires double the material.

However, I don't think raw material cost is a big part of the cost of refrigeration systems anyway.

Re:US companies are producing heat pumps that work below -20... by samtho on Wednesday December 28, 2022 @12:24PM (#34163306)
The “soft” copper tubing they use in refrigerant lines is not only very cheap (it’s not 100% copper) but is very much over built for pressure it is likely going to be subject to. It’s way cheaper, in this instance, to simply sell a line set that works with 99% of systems instead of having dedicated factory lines and consumer confusion from having different grades of registrant tubing.
Re:US companies are producing heat pumps that work below -20... by dragonwriter on Wednesday December 28, 2022 @01:29PM (#34164065)
> For pipes, double the pressure requires double the wall thickness, which requires double the material.

Double the wall thickness requires more than double the material.

Re:US companies are producing heat pumps that work below -20... by lazide on Wednesday December 28, 2022 @11:06PM (#34169424)
Gearing on the motor driving the compressor, compression ratio, etc. all have a huge impact on wear and tear, power requirements, etc.

These all change based on the pressure delta.

Re:US companies are producing heat pumps that work below -20... by raverbashing on Wednesday December 28, 2022 @10:25AM (#34161867)
> The higher pressurizations require more expensive components and compressors

Sure, that sounds like an acceptable compromise for those who need the lower operating temperatures

And maybe technology can get those compressors at the same price point of current compressors

Re:US companies are producing heat pumps that work below -20... by jacquesm on Wednesday December 28, 2022 @11:23AM (#34162523)
But then current compressors would end up cheaper and a difference would still exist.
Re:US companies are producing heat pumps that work below -20... by szundi on Wednesday December 28, 2022 @11:37AM (#34162706)
Or not produced anymore and prices go up for legacy system maintenance. Like try to buy 4MB of EDO RAM
Re:US companies are producing heat pumps that work below -20... by abracadaniel on Wednesday December 28, 2022 @01:12PM (#34163865)
Your point should stand, but it did make me discover that people make new 30pin 4MB simms, which were very difficult to get for years because they were commonly used in ATMs and only available used.
Re:US companies are producing heat pumps that work below -20... by jacquesm on Wednesday December 28, 2022 @05:08PM (#34166660)
I don't think that will happen. The price difference will be substantial due to the changes required and volume will probably not be enough to offset those.
Re:US companies are producing heat pumps that work below -20... by FuriouslyAdrift on Wednesday December 28, 2022 @12:25PM (#34163325)
Scroll compressors have come down in cost a bunch in the last few years. There's really very few reasons not to get a heat pump, now, for new construction.
Re:US companies are producing heat pumps that work below -20... by bityard on Wednesday December 28, 2022 @03:43PM (#34165700)
Even in areas where natural gas is much cheaper than electricity?
Re:US companies are producing heat pumps that work below -20... by dgacmu on Wednesday December 28, 2022 @04:09PM (#34165992)
A heat pump is likely to have an average efficiency of near 300% - call it 250 if you want to hedge. A high efficiency condensing gas furnace gets about 95%. So on a per-watt-hour basis (equiv., BTUs), your gas must cost less than roughly 1/3 what your electric costs.

There are additional savings if your gas furnace is the only gas appliance in your house and you can remove gas service entirely, saving the monthly customer fee.

Re:US companies are producing heat pumps that work below -20... by pandaman on Wednesday December 28, 2022 @05:44PM (#34167041)
And to get to 250% COP in heating on average you'd expect to have, at least, 8.5 HSPF2 rating on your heat pump (it's still just the heating performance w/o de-frosting cycles as far as I understand so the real world COP of a 8.5 HSPF2 will be lower than 2.5)
Re:US companies are producing heat pumps that work below -20... by crgwbr on Wednesday December 28, 2022 @06:43PM (#34167569)
Unfortunately that is the case in some places. Last year I did the math to see if a ground source heat pump would be feasible (Hudson valley, NY), but even accounting for 400% efficiency vs 95% for gas, gas was still ~30% cheaper per month than electric. And that’s ignoring the extra $50k in equipment cost for the heat pump.
Re:US companies are producing heat pumps that work below -20... by crmd on Wednesday December 28, 2022 @07:38PM (#34168014)
Thanks - this is exactly the kind of data point I’m looking for. I have a big, drafty loft in Brooklyn that is heated with gas forced air. I’ve been curious about the relative operating cost of an air source heat pump, and I assume the sky high cost of electricity in nyc makes it a non-starter.
Re:US companies are producing heat pumps that work below -20... by silverlake on Wednesday December 28, 2022 @08:23PM (#34168362)
Also in NYC. I pay roughly 35cents per kWH (air-source heat pump) and $3 per therm natural gas (radiant heat, 95% efficient). I think 1 therm == 100k BTU, 1kWH == 3412 BTU. To equal 1 therm is takes 29kWH of electric heat costing $10.15. Then divide by the efficiency of heat pumps: $3.40 at 300% efficiency, $5 at 200%. I’ve read air-source heat pumps become far less efficient as the temps fall, so < 2x may be more realistic in winter.
Re:US companies are producing heat pumps that work below -20... by crmd on Wednesday December 28, 2022 @09:56PM (#34168924)
Hey, thanks for responding. Am I understanding you correctly that 1 unit of gas heat costs $3 and each unit of heat pump heat costs between $3.40 and $5.00 depending on efficiency of the heat pump?
Re:US companies are producing heat pumps that work below -20... by silverlake on Thursday December 29, 2022 @09:55AM (#34173185)
If my math checks out (which is doubtful) then yes, heat pump could be more expensive than gas heat on the worst cold days like last week (10F). However, a heat pump handles heating and cooling. So it’s cheaper to install 1 system that does everything rather than 2 systems to save money on a few cold days. Add a few solar panels and the heat pump cost goes to 0.

However, we put in a gas combi-boiler for hot water. Since we were renovating a townhouse, it was easy to throw in some radiant heaters on all floors. It’s a quiet, comfortable heat. I have the heat pump set to assist if the temps drop below 68F inside. All that said, insulation and air sealing is by far the most important thing to do first.

FYI: I checked the specs on my unit. It claims a 3.3X COP. So that’s $3 per therm, same as gas.

Re:US companies are producing heat pumps that work below -20... by mechagodzilla on Wednesday December 28, 2022 @10:04PM (#34168975)
NYC’s design temp is like 17F or something, so the seasonal average COP is probably above 3 for good cold climate heat pumps.
Re:US companies are producing heat pumps that work below -20... by dgacmu on Thursday December 29, 2022 @07:34AM (#34171993)
The 300% is closer to an average. When it's over 40F you'll reach over 400% efficiency.

Now a question to address is whether your radiant heat is actually getting 95% efficiency. If you have an old radiator design system that was converted to using a condensing boiler, it may not be designed to keep return temperatures low enough for the boiler to operate at maximal efficiency. (old boiler systems were designed to keep the return water supply hot to prevent acidic condensate from eating the heat exchanger. This is the exact opposite of what you want with a modern system, where the return water needs to be cold enough that the flu gases condense into it to recover heat.)

If you have a way to monitor the return water temperature into your boiler, you could check. You need the return water to be below about 100 Fahrenheit in order to have 95% efficiency.

Re:US companies are producing heat pumps that work below -20... by idontwantthis on Wednesday December 28, 2022 @10:17PM (#34169053)
Would fixing the draft and adding insulation be the most effective first step?
Re:US companies are producing heat pumps that work below -20... by crmd on Wednesday December 28, 2022 @10:40PM (#34169221)
It’s a 630 square foot surface with a 56 degree temperature at the moment according to FLIR. It creates a cascading cool breeze that just neutralizes the forced air furnace. When the furnace stops I can feel the waves of cool air sliding off the external walls.
Re:US companies are producing heat pumps that work below -20... by chii on Wednesday December 28, 2022 @10:33PM (#34169163)
> gas was still ~30% cheaper per month than electric

this sucks, because gas _should not_ be that much cheaper than electricity, but for subsidies or other market altering shenanigans.

Re:US companies are producing heat pumps that work below -20... by tshaddox on Wednesday December 28, 2022 @10:38PM (#34169199)
Namely externalities. Natural gas is almost certainly more expensive for home heating than electricity, it’s just that a portion of that expense is paid by a large number of third parties.
Re:US companies are producing heat pumps that work below -20... by rsj_hn on Wednesday December 28, 2022 @11:14PM (#34169474)
Seeing as how natural gas is a required input for making synthetic fertilizer, without which billions would starve, it's hard to think of a product with more positive externalities than natural gas. Every time you go to the supermarket, you should be thankful that natural gas allows synthetic fertilizers to feed the world.

It's easy to think of negative externalities and ignore positive externalities (or vice versa), but accurately summing these up is very difficult.

Re:US companies are producing heat pumps that work below -20... by tshaddox on Thursday December 29, 2022 @12:38AM (#34169882)
I didn’t say that all natural gas usage has negative externalities. But also, don’t the natural gas costs you’re talking about show up in the price of food?
Re:US companies are producing heat pumps that work below -20... by rsj_hn on Thursday December 29, 2022 @05:59AM (#34171457)
No, because prices are set by supply and demand, not the total social cost/benefit that obtains when all effects, direct and indirect, are taken into account.

It is the discrepancy between market equilibria and total social cost/benefit that creates the theory of externalities. But my point is that actually determining social cost/benefit requires very extensive knowledge of all the social benefits and costs provided by something. For example, if you were to ask me what the positive externalities of clean drinking water are, I'd say they are enormous. But I couldn't really give you a number, and if anyone tries to give you a number, they are lying. But that is why I support subsidizing access to clean drinking water, rather than letting the market sort it out. It's just too valuable.

When we are talking about things like energy or transportation, they generally have enormous positive externalities, which is why they are historically subsidized. For example, even if you never use a road, you benefit from the stores you buy from having access to roads so that goods can be delivered to them more cheaply. But it's even more subtle, because cheaper transportation means bigger markets. One of the reasons why local businesses historically opposed the construction of roads is that it would force them to compete with other businesses along the same road. If most people had to walk, then they get a captive market. As soon as you introduce roads, prices come down, and quality increases because lots of little monopolies are destroyed.

So even if you never leave your house and only shop locally, you are getting huge financial benefits from cheap transportation. Thus there is a positive externality. This is why we don't mind that trucks cause most of the damage to roads but don't "pay their fair share" of road maintenance costs. It's because those trucks create enormous positive externalities by making all the goods we buy much cheaper, even if we ourselves never hire a truck. This is also why many nations subsidize railroads, bridges, roads, etc. The internet also has this aspect of enormous positive externalities. And when you are talking about energy -- it's the basis of modern civilization. Again, if you never use any energy yourself except wood that you chop down, you benefit from all the others who provide you with services having access to energy.

Now I'm not saying that natural gas only has positive externalities and that there are no negative externalities. What I'm saying is that no one can tell you what the net is, because these are things foundational to our economy and have profound effects on everything else.

So I would not try to use the logic of externalities when talking about these foundational technologies. Externalities makes sense if you are using a lawnmower and it annoys your neighbors, so you let them bid on how much you need to pay them in order to keep using the lawnmower. In very simple models, it makes sense. In the real world, it almost never makes sense, and ends up being a type of economic smokescreen for what is basically politics choosing winners and losers based on arbitrary or cherry picked criteria.

So my recommendation is to not try to use "externalities" as a justification. Here's what I would argue, for example, when I am dictator. We want to transition to nuclear power and away from natural gas. So let's tax natural gas and use the money to pay for nuclear power so that it becomes cost competitive with natural gas, and then let's reserve natural gas for things nuclear can't do for us -- such as creating fertilizers. See what I did there? I made my actual motivation the main cause and didn't invoke any economic theory of externalities. Because overall goals should not be slaves to economic models, but rather the economic models should be servants of the overall social goals. The economic model can tell you how much to tax natural gas so that nuclear becomes cost competitive. But whether to decide to switch away from one source to another requires wisdom rather than brute force calculation of all outcomes -- there is no economic model that can spit out the answer. We should not give economists that type of power.

Re:US companies are producing heat pumps that work below -20... by tshaddox on Thursday December 29, 2022 @08:08PM (#34180358)
I understand the theory of externalities. I certainly understand that it’s difficult or impossible to know all costs to all parties for some good. But that doesn’t mean there aren’t pretty clear examples, like burning fossil fuels. It certainly doesn’t mean you can dismiss any mention of externalities simply because they are complicated. Some people are bald.

You talk about how certain goods are immensely beneficial to society, but that’s not sufficient to claim there are positive externalities. Your example of a road being used by a store that you buy from is a poor example. Those transportation costs would simply show up in the cost of the stuff you buy (disregarding government subsidies for roads, of course, but that’s a separate issue).

Re:US companies are producing heat pumps that work below -20... by matsemann on Thursday December 29, 2022 @03:57AM (#34170827)
Well, wouldn't it then be better to use the gas for that, and use other means for heating homes?
Re:US companies are producing heat pumps that work below -20... by rsj_hn on Thursday December 29, 2022 @06:46AM (#34171699)
Yes, using natural gas for the things that only natural gas can do would be an excellent public policy.

However that's not the policy we are pursuing. We are pursuing very blunt instruments to try to discourage investment in developing natural gas fields full stop. Which is bad public policy.

The other issue is by raising the price of natural gas, we are raising its price for all uses. And the price of natural gas tends to determine the price of fertilizer, which tends to determine the price of food. So this policy makes food more expensive.

Even worse, natural gas and things like coal and oil are in some sense substitutes. Not perfect substitutes, but what happens when we make oil more expensive is that people shift to coal and natural gas to generate energy, and so these two become more expensive as well. Similarly, if we were take all coal offline, that would increase demand for natural gas and oil as substitutes, and again, the price of these commodities would rise, which would increase the price of food.

What would be nice would be to see if we could de-couple these prices somehow -- e.g. tax usages of natural gas downstream of the price of the commodity itself. Other ideas are also possible.

Re:US companies are producing heat pumps that work below -20... by lazide on Wednesday December 28, 2022 @11:01PM (#34169394)
Gas is a defacto waste product from oil extraction, and very energy dense.

It’s shocking it’s not a bigger delta the other way.

Re:US companies are producing heat pumps that work below -20... by nicpottier on Wednesday December 28, 2022 @11:36PM (#34169599)
$50k in equipment? At what scale are we talking. I got a Mitsubishi heat pump with three heads installed for less than $15k and it works well into the negatives.
Re:US companies are producing heat pumps that work below -20... by manfre on Thursday December 29, 2022 @12:12AM (#34169769)
Ground source requires drilling and is not the more common type of heat pump found at most homes.
Re:US companies are producing heat pumps that work below -20... by brnt on Thursday December 29, 2022 @08:14AM (#34172278)
Note that you are unlikely to achieve 95% efficiency on the gas. That requires you to run your plumbing at about 20 degrees (celcius), since burning gas means simple thermodynamics apply. At 40C you're already down to 90%, and virtually every installation I've seen actually is set to 60-80 degrees, at which point you're nearing an efficiency of only half.

Hotter water means a more reactive system and smaller radiators (you'll need five times the volume for a given power output when you compare plumbing water of ~30 to 70+. You are almost certainly not installing that. Maybe you are installing floor heating, in which case you are likely OK.

But most people I speak to don't realize that 1. Gas efficiency goes up as temperature differential goes down, and 2. energy transfered to water also needs to leave the system at your radiators. So size them for the effiency you want, or be disappointed with a significantly higher gas bill.

Re:US companies are producing heat pumps that work below -20... by bityard on Thursday December 29, 2022 @10:34PM (#34181472)
I don't have any hard data at hand, but I can say that running my AC (which is just a one-way heat pump) for a few days out of the month in the summer makes my combined gas+electric bill about the same as in the middle of winter when my gas furnace is running all the time.
Re:US companies are producing heat pumps that work below -20... by FriedPickles on Wednesday December 28, 2022 @04:23PM (#34166167)
Id love to see a combined heat and power system that burns natural gas to drive a heat pump compressor, and recovers the combustion heat. I wonder what multiplier it would get on a therm.
Re:US companies are producing heat pumps that work below -20... by nanomonkey on Wednesday December 28, 2022 @04:54PM (#34166524)
I've been contemplating the same thing. Something like the WhisperGen stirling engine hot water heater should be available to everyone. Hell even a water cooled honda generator that runs off natural gas, and pumps the radiator fluid into your home for heating purposes would be nice. It seems weird that we aren't producing electricity when ever you burn natural gas for heating.
Re:US companies are producing heat pumps that work below -20... by lazide on Wednesday December 28, 2022 @11:05PM (#34169418)
The issue is maintenance and capital expense due to complexity.

Gas furnaces are dead simple, and still break and require maintenance. Heat pumps, more so. Generators? By far the most.

Combining the three sounds like a huge headache for marginal efficiency gains.

Re:US companies are producing heat pumps that work below -20... by nanomonkey on Thursday December 29, 2022 @05:33PM (#34178990)
This is why I started off referencing external combustion engines like Stirling engines. These tend to have very low maintenance needs as the combustion occurs outside of the pistons, so there is no fouling of the moving parts. One could use self lubricating materials like graphite rods as your piston heads and have quite high reliable components. The stirling engines that NASA utilizes are considered maintenance free.

As far as efficiency gains, we're talking 25-40% of the energy being produced as electricity and the majority of the rest being turned into hot water for residential use, either by one household or a whole city block. This doesn't sound like a terribly marginal gain. Specially if the energy production is done during the hours when traditional solar installations are not producing which are generally when folks are running their heating.

Re:US companies are producing heat pumps that work below -20... by maxerickson on Thursday December 29, 2022 @11:43AM (#34174498)
Generators with heat recovery exist, search on micro CHP.
Re:US companies are producing heat pumps that work below -20... by nanomonkey on Thursday December 29, 2022 @05:34PM (#34179004)
Yes thanks, I'm aware. I have actually worked in this field in the past building wood gasification micro CHP units.
Re:US companies are producing heat pumps that work below -20... by mindslight on Wednesday December 28, 2022 @05:34PM (#34166942)
There are refrigerators that run directly off of propane. https://www.ferrellgas.com/tank-talk/blog-articles/how-propa...

The working temperatures of ammonia are probably wrong for a heat pump, but perhaps something similar could be devised.

Re:US companies are producing heat pumps that work below -20... by icedistilled on Wednesday December 28, 2022 @04:05PM (#34165937)
yes. Because Global warming/climate change is real and installing new furnaces bakes in decades of additional natural gas usage. Also, that natural gas price may change.
Re:US companies are producing heat pumps that work below -20... by bombcar on Wednesday December 28, 2022 @06:35PM (#34167501)
If you want to spend the money you can get systems that have heat pump, gas furnace/boiler, and electric. Often used for larger installations that can take advantage of differing prices - and can work best with water heat.
Re:US companies are producing heat pumps that work below -20... by nightski on Wednesday December 28, 2022 @04:23PM (#34166166)
The main reason in my area is that a.) these fancy new efficient ones aren't available easily and b.) no contractors in the area to install/service them. I just got a new gas furnace and really wanted to add a heat pump to the mix but after several quotes all of them either said no or strongly avoided the question. I couldn't get a straight answer.
Re:US companies are producing heat pumps that work below -20... by londons_explore on Wednesday December 28, 2022 @01:19PM (#34163959)
> then the boiling point of the refrigerant must be below -20F

This isn't the limiting factor for choice of refrigerant... There is always a low enough pressure that anything boils.

The problem is that at very low pressures (think a few millibars), gasses need huge diameter pipes and huge pumps to move even a small number of kilowatts of heat.

Re:US companies are producing heat pumps that work below -20... by brilee on Wednesday December 28, 2022 @02:30PM (#34164828)
Another issue is that at pressures below one atmosphere, the system will suck in ambient air, causing condensation to collect inside your refrigeration circuit, which creates ice crystals, etc… nobody does that.
Re:US companies are producing heat pumps that work below -20... by londons_explore on Wednesday December 28, 2022 @03:22PM (#34165437)
Plenty of systems work below atmospheric pressure. For example, Fridge freezers most commonly use isobutane (R600a), and when operating with the freezer at -20C, the pressure will be half an atmosphere (ie. -0.5 bar below atmospheric).

The systems are filled using a vacuum pump to ensure there is very little atmospheric air in them, and they also use a 'filter dryer', which is a chemical compound chosen to trap any remaining water and various other common contaminants.

Re:US companies are producing heat pumps that work below -20... by mateo1 on Thursday December 29, 2022 @01:34AM (#34170147)
On top of that, the maximum theoretical COP for a cold source at -30c and a hot side at 35c is 4.7. Real world heat pumps usually get half of that, possibly even less for this extreme delta t, so around 2. Natural gas tends to cost less than half per unit energy compare to electricity, even less typically, so you'll never make back the capital costs. Of course if this technology matures to the extend it's much, much cheaper and you tend to have milder winters and hot summers it's good enough and possibly worth it, but we haven't gotten to maintenance and installation costs yet, as the 35c hot temp assumes underfloor heating or tons of fancoils which have their own issues, the fact that the heat pump must be massively overspectd to output enough heat in peak conditions etc.