https://michael.stapelberg.ch/posts/2024-07-02-ryzen-7-mini-...
Perhaps it can be configured to meet your requirement for "affordable"?
However there are many NUC-like small computers made by various Chinese companies, with AMD Ryzen CPUs and with 2 SODIMM sockets, in which you can use 64 GB of DRAM.
Those using older Ryzen models, like the 5000 series, may be found at prices between $220 and $350. Those using newer Ryzen models, up to Zen 4 based 7000 or 8000 series, are more expensive, i.e. between $400 and $600.
While there are dozens of very cheap computer models made by Chinese firms, the similar models made by ASUS or the like are significantly more expensive. After the Intel NUC line has been bought by ASUS, they have raised its prices a lot.
Even so, if a non-Chinese computer is desired and 64 GB is the only requirement, then Intel NUCs from older generations like NUC 13 or NUC 12, with Core i3 CPUs, can still be found at prices between $350 and $400 (the traditional prices of barebone Intel NUCs were $350 for Core i3, $500 for Core i5 and $650 for Core i7, but they have been raised a lot for the latest models).
EDIT: Looking now at Newegg, I see various variants of ASUS NUC 14 Pro with the Intel Core 3 100U CPU, which are under $400 (barebone).
It should be noted that this CPU is a Raptor Lake Refresh and not a Meteor Lake CPU, like in the more expensive models of NUC 14 Pro.
This is a small computer designed to work reliably for many years on a 24/7 schedule, so if reliability would be important, especially when using it as a server, I would choose this. It supports up to 96 GB of DRAM (with two 48 GB SODIMMs). If performance per dollar would be more important, then there are cheaper and faster computers with Ryzen CPUs, made by Chinese companies like Minisforum or Beelink.
1. Newer DAS devices connect using USB-C, but USB type-A/e-SATA ones can be found.
I also want to set up a NAS on a mini-PC with some sort of attached external storage, but I haven't been able to get past this blocker. USB is the only external interface these mini PCs typically support.
Similarly, heres a very low power writeup I did for using 2.5" drives with a dedicated power hub/splitter. http://www.jofla.net/?p=00000106#00000106 This will still have issues if the mains lines sag (a pole goes down somewhere), but you can fix it with a reboot remotely. Other than that it works great.
This was/is definitely a labor of love, primarily as I've come from a time when all you could get for a server were huge boxes idling at 50 watts, so i felt guilty of all the power I used to consume.
You're right, and I don't recommend USB as the only backup solution. I an old eSATA enclosure - not sure if that's an improvement over plain USB - as a secondary backup and keep the device on long enough to complete)
You could also buy a PCIe to multiport SATA (RAID) card, but you'll also need a bigger[1] NAS-like case[2] to house the hard drives and multiple power cables for the drives
1. Depending on how mini your PC is and how many drives you want to attach to it
2. I have noticed any case that's sufficiently NAS-like (hotswap trays) is sold at a premium.
The PC's PSU will need SATA power on its cables or else you'll need to scavenge a separate PSU and use the paper clip trick (or better yet, a purpose built connector) to get it to power things on without a motherboard connected.
Once you have all of that, then it's just a matter of housing the disks. People have done this with everything from threaded rod and plastidip to 3D printed disk racks to used enterprise JBOD enclosures (Just a Bunch Of Disks, no joke).
Total cost for this setup, excluding the disks, can easily be done for less than $200 if you're patient and look for local deals, like a Craiglist post for a bunch of old server hardware that says "free, just come haul it away".
Check or r/DataHoarder on reddit or ServeTheHome's blog
https://www.reddit.com/r/intelnuc/comments/ibchlz/nuc_m2_sat...
If it was just one, I'd put it down to random bad luck. But with that many failures I assume they are doing something stupid/cheap.
Usually they would simply fail to power on but sometimes individual slots seemed to die (which RAID just loooooves).
And having an entire enclosure fail and waiting days/weeks for a replacement sucks as you lose access to all your data.
I eventually bought a Jonsbo N3 off of Aliexpress and PCI SATA card (to support more than the 2-4 drives most motherboards support) and that has been working well for months.
The Jonsbo N3 is not comparable. I own one as well (how quiet is yours? I upgraded the rear fan but my CPU fan is noisy), but it's a complete PC case, not an external HDD array.
There is one deeply troubling flaw to them though, they don't turn back on of the power goes out, until you physically hit the button again. I think this is alas all to common for many of these enclosures!
W.r.t. GPIOs, I agree, that delegating that to an e.g. Arduino connected via USB/UART or one of the available internal(often RTC), or external(HDMI/VGA) I2C connections as an I2C slave is the preferred solution.
Do you have a list of remaining, large deficits in Linux power management, because I'm not finding many urgent open issues in that area?
Examples:
- PINE64 Rock64 running FreeBSD 14.1 replaced an aging RPi3. I use this for SDR applications. It's a small, low power device with PoE that I can deploy close to my outdoor antennas (e.g. 1090mhz for dump1090-fa ADS-B). It's been really solid with its eMMC, and FreeBSD has good USB support for RTL-SDR devices.
- PINE64 RockPro64 running NetBSD 10. I have a PCIe card with a 500gb SSD M.2 slot. NetBSD has ZFS support and it has been stable. This lets me take snapshots on the SSD zpool. I generate time-lapse videos using the faster cores.
You don't get 100% HW support (e.g. no camera support for RockPro64) but I don't need it. The compromise is worth it in my case because I get a stable and consistent system that I'm familiar with: BSD.
they are my favorite 'home server' currently...cheap, standard, and expandable - oh! And SILENT! :-)
Two of the three ODROID H4 variants use the "Intel Processor N97" CPU, which is intended for embedded applications and it appears to support In-Band ECC, even if this is not clearly advertised on Intel Ark (i.e. at other CPUs of the Alder Lake N family, like i3-N305, at ECC Support it says "No", but at N97 it says neither "Yes" nor "No", but it is mentioned that it is intended for embedded applications, not for consumer applications, and the embedded models normally support In-Band ECC).
The ODROID H4 BIOS allows to enable In-Band ECC on ODROID H4 or ODROID H4+ (the latter is slightly more expensive at $139, but it has more I/O, including two 2.5 Gb/s Ethernet ports and four SATA ports; to the bare board you must add between $10 and $20 for the case, depending on its size, and a few other $ for SATA cables, RTC battery and optionally a cooling fan; you must also buy one 16 GB or 32 GB DDR5-4800 SODIMM, so after adding shipping and taxes a NAS would cost a little more than $200, besides the SSDs or HDDs).
You can see test results with ECC enabled at:
https://www.cnx-software.com/2024/05/26/odroid-h4-plus-revie...
[0] - https://www.anandtech.com/show/18732/asrock-industrial-nucs-...
[1] https://forums.unraid.net/topic/167669-odroid-h4-intel-n97-2...
[2] https://forum.odroid.com/viewtopic.php?p=384823#p384823
[3] https://wiki.odroid.com/odroid-h4/hardware/h4_bios_update#bi...
The Dell's coming off lease now have modern features including Intel 8th Gen CPUs with TPM and USB-C etc...
I cannot say no to cheap compute for some reason.
I sympathise - for me I think it comes from growing up with early generation PCs that were expensive, hard to get, and not very performant; now you can buy something that's a supercomputer by comparison for almost nothing. Who can resist that?! I'll think of something to do with them all eventually...
I bought them them for 50 euro a piece without RAM and disks.
The only downside is that it doesn't have space for multiple 2,5/3,5 disks, but that is just personal preference anyway.
> Next Unit of Computing (NUC) is a line of small-form-factor barebone computer kits designed by Intel.
Ref: https://en.wikipedia.org/wiki/Next_Unit_of_ComputingThey look even smaller than one litre PCs.
If you care about power consumption like I do, you can Google "$model energy consumption white paper" which contains very accurate data about idle usage, for example https://sp.ts.fujitsu.com/dmsp/Publications/public/wp-energy...
In one case I had a nuc where on Linux after enabling power saving features for the sata controller, idle usage even fell to 5W when the pdf claimed 9.
Having an actual pc instead of a random sbc ensures best connectivity, expandability, and software support forever. With almost all sbcs you're stuck with a random-ass kernel from when the damn thing was released, and you basically have to frankenstein together your own up-to-date distro with the old kernel because the vendor certainly doesn't care about updating the random armbian fork they created for that thing.