Why would they. Most of those things are not sustainable.
You don't want alluminium wires in your car.
Where aluminum causes fires is due to the fact that it expands and contracts more than copper does, and it can oxidize and corrode when not properly cared for (for example, when dissimilar metals are used, or when exposed aluminum wire ends are not properly coated).
We can assume that someone at Tesla is familiar with the properties of aluminum and can insure that they are using the right connectors to mitigate these issues. (or at least, we can hope)
Aluminum was used for a short time in the west for household wiring and was quickly outlawed.
Why not? I^2*r says that running 75% less current will generate 94% less heat.
Existing copper wires would be a disaster if cars ran on a 3V system. Aluminum at 48V will be fine, as long as it’s sized appropriately the same way copper is today.
Thats not the argument, you can do that now with copper cables.
Aluminium is a good conductor, but it is reactive, brittle and not as malleable as copper.
also, copper has almost half the resistance per meter than aluminium. So even for solid bus bars, it doesn't make that much sense, unless you have structural bus bars.
But 4 times the weight
And twice the resistance doesn’t matter. So you go one gauge bigger. If the material is cheaper, more available, and suitable, that’s fine. We don’t insist on gold wires because they’re “better” than copper.
It’s all tradeoffs. I don’t see a reason to be philosophically opposed to aluminum other than “it’s possible to do it wrong”, which is of course also true for copper.
Indeed, but automotive wiring is subject to intense and persistent vibration and heat cycles. so all those ties become stress points for fatigue to cluster around.
I'm not saying its never a good idea to use an aluminium wire loom, but I'm struggling to find a situation where its required
It's not really the flexible thing you picture with the word "loom." The solid aluminum conductor is inside an aluminum tube (mounted to the body), with insulation between.
These are thick high voltage conductors. I'm sure Tesla did their homework on flex and fatigue.
The place we saw this used was for fixed rigid bus bars, notably the "cable" from the charge port to the battery.[0]
Previously they used traditional stranded copper. Now it's a solid aluminum conductor, wrapped in insulation and protected by an outer aluminum tube.
>copper has almost half the resistance per meter than aluminium
That's why I mentioned conductivity-to-weight, which is the more critical metric. Copper is over 3x as dense, at 9.0 g/cm³ vs 2.7 g/cm³ for aluminum.
It doesn't hurt that aluminum is cheaper and far more abundant.
Additionally, aircraft airframes are regularly inspected and fully radiographed at certain intervals. Components that develop flaws are changed out when the flaws are detected. The same is not true of cars.
Why not?
If Tesla has switched to aluminum I imagine they've found a way to fix that. Possibly by making the entire electrical system out of aluminum, so that it all expands the same way, or possibly a connector designed to avoid that.
Properly terminated, there is no problem with aluminum wiring in your house. As another replier mentioned, most houses do have aluminum wiring in the run to the house and the run from the meter to the panel, and sometimes in the larger runs like stove and dryer.
It's also worth noting that the newer aluminum formulas like Southwire SIMpul, are not like the old aluminum like was installed in my house in the early '70s. But, buyers are still gunshy from the '70s, so copper is generally preferred
I think that everyone should look on his "forward looking statements" with a higher than normal degree of skepticism. He does seem to pull off a lot of outlandish stuff, though, so it doesn't pay to be too skeptical.
> I consider him and his companies to be completely untrustworthy. He could be selling water in the desert and I still would never buy another thing from him.
I don't think that that same level of skepticism is warranted towards his statements about what is true today. But then again, I haven't been following him very closely, so maybe his pant are constantly on fire.
https://twitter.com/ICannot_Enough/status/161837414087616512...
This is about as silly as people who think he’s the messiah. He’s clearly over promised on many things, but he’s also delivered on a lot.
And spacex motto is turning the impossible into late, so he’s being pretty honest about his goals being off. What’s the issue? Why do you hate him so much?
In an interview by Munro[1] , Elon Musk previously mentioned the desire to switch to 48V together with the desire to use PoE. Combining data and power over the same wires.
The move of automakers to 48V has been in the works for a while:
* https://www.autoevolution.com/news/understanding-the-shift-t...
* https://whma.org/overview-of-48-volt-systems-in-the-automoti...
* https://www.google.com/search?q=48V+cars
It's just a bit of a co-ordination / chicken-egg problem in that equipment probably has to be to handle 12V and 48V for a while during a transition period.
Tesla seems to be the leader here. Per Investor Day[0] and other sources, they
- developed low-cobalt and low-nickel cathodes, to reduce scarce battery metals
- increased overall vehicle efficiency to allow iron cathodes which are earth-abundant
- consolidated electronic modules to reduce microchips and wiring
- are soon switching to 48V, to further reduce low-voltage copper wiring (copper being a 'medium-rare' metal)
- switched from copper to aluminum high voltage conductors (per Munro Live), aluminum having better conductivity-to-weight
- reduced vehicle structure with structural battery design and 'gigacasting' manufacturing
Many of these seem to benefit from vertical integration.
Are any other manufacturers pushing as hard here?
[0] https://m.youtube.com/watch?v=Hl1zEzVUV7w&t=1875s