Re:RJ45-sized Linux networking server goes IPv6
by pmorici on Saturday December 14, 2013 @10:10PM
(#6908201)
I've used one of these before. They are useful for attaching serial devices to an Ethernet network. It's a lot cheaper and easier than trying to put a PC with enough serial ports near every device you need to talk to. The ones I worked with were part of a radio modem sold by MaxStream, now part of Digi International.
Re:RJ45-sized Linux networking server goes IPv6
by pmorici on Sunday December 15, 2013 @03:59PM
(#6910833)
That is essentially what these are. The default Lantronix firmware allows you to connect to the device on a specific TCP port and talk to the serial device on the other side. You configure them over HTTP or Telnet.
Re:RJ45-sized Linux networking server goes IPv6
by analog31 on Saturday December 14, 2013 @11:22PM
(#6908372)
I use microcontrollers for prototyping and proof-of-concept work. Often I combine multiple devices into a system that I can control from a PC. It's been my experience that dropping in a something-to-serial converter is 100x easier than trying to install and understand a communication protocol "stack," even if the code and documentation is supplied by the chip vendor.
I tend to use little USB-to-serial breakout boards, but I'd do the same with RJ45 if I needed that interface.
Once something of mine is ready to commercialize, it gets handed over to professional developers who tend to prefer the built-in firmware based approach, but they end up spending a lot of time debugging those interfaces.
Re:RJ45-sized Linux networking server goes IPv6
by dlctr on Monday December 16, 2013 @02:44AM
(#6913399)
The arduino yun [1] combines an linux-based SoC with a microcontroller on a single board. So you can have both, networking and applications in practically any language, and an internal interface to a microcontroller.
For only accessing a rs232 serial port over ethernet, there are easier solutions. But if you need multiple of such ports, sensor access, etc. its quite a nice combination.
Re:RJ45-sized Linux networking server goes IPv6
by joezydeco on Saturday December 14, 2013 @09:06PM
(#6908005)
I've had good success with the NXP LPC178x series. Cortex M3 with onboard Flash and SRAM. Ethernet is onboard and easy to attach with a simple PHY, also works well with extenral SDRAM and expanded Flash.
Re:RJ45-sized Linux networking server goes IPv6
by tlarkworthy on Saturday December 14, 2013 @09:12PM
(#6908026)
yeah I also used that a while ago, but I don't think I can fit an ethernet client for Robotic Operating System on it. Doesn't appear straight forward anyway:-
Re:RJ45-sized Linux networking server goes IPv6
by SwellJoe on Saturday December 14, 2013 @08:50PM
(#6907965)
I immediately imagined adding web UIs, or simply network APIs, to various "dumb" hardware. Attach it to a ADC/DAC and suddenly a lot of things become computer controllable. It's small enough to stick it on most electronic device boards without major changes.
Re:RJ45-sized Linux networking server goes IPv6
by RankingMember on Saturday December 14, 2013 @07:49PM
(#6907796)
Yeah these sort of "look at how small this fully functional computer is" pieces always make me wonder if they have a real world appeal or if they're more a proof-of-concept or tech demo to pull people's attention to the company's other products.
Re:RJ45-sized Linux networking server goes IPv6
by throwaway2048 on Saturday December 14, 2013 @08:12PM
(#6907849)
this would be fantastic for corporate espionage, snap one into an unused to drop somewhere and you have a beachhead inside the network. Combine it with a Micro SD card you have a great way to exfiltrate data via weekly/monthly data drops, without setting off external firewalls.
Re:RJ45-sized Linux networking server goes IPv6
by joezydeco on Saturday December 14, 2013 @08:55PM
(#6907982)
I didn't see PoE on this device, you need to supply 3.3VDC to make it run. So do you want to attach a wall wart? I don't think it will run long off a lithium cell.
Re:RJ45-sized Linux networking server goes IPv6
by splitbrain on Saturday December 14, 2013 @07:56PM
(#6907819)
Isn't IPv6 a feature of the Linux networking stack? Shouldn't everything that runs Linux be IPv6 capable? Or is there some IPv6 stuff implemented in hardware here?
Re:RJ45-sized Linux networking server goes IPv6
by ghshephard on Sunday December 15, 2013 @01:02AM
(#6908553)
The author writing this article picked up something nonsensical - the entire second half suggested they knew little to nothing about the IPv6 protocol, and this devices implications for such, including statements like, " formally launched in June 2012. "
I tend to use little USB-to-serial breakout boards, but I'd do the same with RJ45 if I needed that interface.
Once something of mine is ready to commercialize, it gets handed over to professional developers who tend to prefer the built-in firmware based approach, but they end up spending a lot of time debugging those interfaces.
https://atlas.ripe.net/
For only accessing a rs232 serial port over ethernet, there are easier solutions. But if you need multiple of such ports, sensor access, etc. its quite a nice combination.
[1] http://arduino.cc/en/Main/ArduinoBoardYun?from=Main.ArduinoY...
http://mbed.org/forum/bugs-suggestions/topic/2662/?page=1#co...
Hmm, that Xport product is £50 from mouser. Not bad
The other option is something like the TI CC3000, a serially driven wifi module. Adafruit just launched a cheap breakout module.
http://www.adafruit.com/products/1469
EDIT: also can't find evidence of a ROS client working on ucLinux :(
http://www.teamfdi.com/development-tools-kits/products/1/DK-...
http://linuxgizmos.com/worlds-smallest-linux-webserver/
Also, it's MB not Mb. The difference between the two is a factor of 8.
http://forums.lantronix.com/showthread.php?t=857
http://www.freescale.com/webapp/sps/site/prod_summary.jsp?co...
> The 32-bit RISC CPU appears to be the same, but instead of coming standard with 8MB SDRAM, it now ships with the previously optional 16MB.