News for hackers. Stuff that matters.
Re:Why Carmakers Can’t Transition to Newer Chips by schiffern on Saturday October 02, 2021 @11:12AM (#28729184)
> “We were able to substitute alternative chips, and then write the firmware in a matter of weeks,” Musk said. “It’s not just a matter of swapping out a chip; you also have to rewrite the software.”

https://www.theverge.com/2021/7/26/22595060/tesla-chip-short...

Re:Why Carmakers Can’t Transition to Newer Chips by 01100011 on Saturday October 02, 2021 @11:25AM (#28729315)
As far as I can tell, Tesla plays fast and loose, treating their product like a manufacturer of consumer electronics and not a manufacturer of a dangerous and durable good. That obviously allows them to out-compete other auto manufacturers who are more aware of things like product liability.

See the Toyota accelerator-gate lawsuits. From https://en.wikipedia.org/wiki/2009%E2%80%932011_Toyota_vehic... :

> However, on October 24, 2013, a jury ruled against Toyota and found that unintended acceleration could have been caused due to deficiencies in the drive-by-wire throttle system or Electronic Throttle Control System (ETCS). Michael Barr of the Barr Group testified[30] that NASA had not been able to complete its examination of Toyota's ETCS and that Toyota did not follow best practices for real time life critical software, and that a single bit flip which can be caused by cosmic rays could cause unintended acceleration. As well, the run-time stack of the real-time operating system was not large enough and that it was possible for the stack to grow large enough to overwrite data that could cause unintended acceleration.[31][32] As a result, Toyota has entered into settlement talks with its plaintiffs.

Not following software best practices(i.e. ISO 26262) can expose your customers to unnecessary risk and leave your company vulnerable to lawsuits. Tesla may learn a very expensive lesson one day, or they may get lucky. Time will tell.

---

Depending on the design of your system and software stack, switching SoCs can be anywhere from a massive effort to a simple recompilation. Even switching architectures could be trivial for some components(i.e. a UI written in HTML5 making REST API calls) or a nightmare for others(ECU, ABS or other real-time algorithm written to use bare metal modules on the SoC without an OS providing abstraction).

Re:Why Carmakers Can’t Transition to Newer Chips by shiftpgdn on Saturday October 02, 2021 @11:34AM (#28729417)
Toyota accelerator-gate is largely a farce. Almost all of the people involved with Toyota unintended acceleration were over the age of 65 and had the poorly designed loose floor mats in their cars.

Even if they had perfect readable John Carmack tier coding they still would have lost.

Re:Why Carmakers Can’t Transition to Newer Chips by 01100011 on Saturday October 02, 2021 @11:50AM (#28729555)
Sure but that's not related to the point I'm making. The point is that not following software design best practices can leave you open to liability, or at least put you in such a weak legal position that you are compelled to settle.

If/when Tesla gets hauled into court over its software flaws, any lack of adherence to best practices will make the company appear negligent.

Re:Why Carmakers Can’t Transition to Newer Chips by thoughtstheseus on Saturday October 02, 2021 @01:41PM (#28730430)
This is a risk adverse culture then. Tesla is spending gobs of money specifically on building safer if not the safest cars out there.
Re:Why Carmakers Can’t Transition to Newer Chips by giantrobot on Saturday October 02, 2021 @05:14PM (#28732141)
> building safer if not the safest cars out there

Unless the car loses power and catches fire. Then you can't open the fucking doors [0].

[0] https://www.washingtonpost.com/business/2019/10/23/man-died-...

Re:Why Carmakers Can’t Transition to Newer Chips by panick21 on Sunday October 03, 2021 @03:34PM (#28739869)
Using 1 off cases based on unsubstantiated information in a lawsuit is not a persuasive argument for overall safety.
Re:Why Carmakers Can’t Transition to Newer Chips by karottenreibe on Monday October 04, 2021 @03:00AM (#28743907)
It's certainly a better argument than the GPs claim of "the safest cars out there" with 0 evidence given to substantiate that. I think it fair to refute such an unsubstantiated claim with a reported instance where safety was not maintained as can reasonably be expected.
Re:Why Carmakers Can’t Transition to Newer Chips by panick21 on Monday October 04, 2021 @08:27AM (#28745781)
Tesla cars have the highest safety ratings in the world and they have the the best active safety features and complete fleet compliance with their whole fleet for new standard of active safety features (literally the only company that does have that).

This is literally just the basic fact of the situation. If you want to disagree with literally every state safety agency in the world, then you are the one who needs to come up with real evidence.

Re:Why Carmakers Can’t Transition to Newer Chips by kevingadd on Saturday October 02, 2021 @02:40PM (#28730925)
How do you square that with them removing sensors from their cars and going all-in on doing self-driving exclusively using vision? If they were so passionate about spending money to make the safest cars, they'd be doing sensor fusion.
Re:Why Carmakers Can’t Transition to Newer Chips by tantony on Saturday October 02, 2021 @03:21PM (#28731212)
> If they were so passionate about spending money to make the safest cars, they'd be doing sensor fusion.

That's your opinion. They have shown data where the information from radar was of a lower quality than what their vision stack was providing (e.g. lack of vertical resolution). Watch their AI day webcast for examples. Their current vision-only stack has been validated with LIDAR ground-truth data.

Re:Why Carmakers Can’t Transition to Newer Chips by heeen2 on Saturday October 02, 2021 @03:32PM (#28731307)
Is anyone arguing for replacing vision with lidar and radar instead of combining it?
Re:Why Carmakers Can’t Transition to Newer Chips by tantony on Saturday October 02, 2021 @09:30PM (#28733775)
If the radar data conflicts with what vision is saying, which one do they trust? They have shown that their vision stack has surpassed what they can do with radar. So "fusing" that data in only makes it worse when it gives conflicting information.
Re:Why Carmakers Can’t Transition to Newer Chips by pas on Sunday October 03, 2021 @07:24PM (#28741436)
Sensors are obviously important, but it doesn't really matter if two sensors conflict, the important thing is which one is consistent with their running model.

So far their biggest problem is that they allow flicker. That's why sometimes the software picks the wrong lines. (Of course this is a very hard problem. Our brain conveniently smooths over sensory changes for us, because that's how our everyday reality is. Things don't flicker in and out of existence, nor does a car suddenly appear as a different thing, then switches back.)

And if it turns out the sensor(s) failed, it has to be able to handle that too.

Re:Why Carmakers Can’t Transition to Newer Chips by jcampbell1 on Saturday October 02, 2021 @02:10PM (#28730670)
I worked for ford many years ago and I remember a really funny conversation between young engineers and MBA types. The issue was the Lincoln Towncar was designed to have extremely low pedal pressure because that is what the old buyers liked. Combine old people with limited hearing, no pedal pressure, and a quiet cabin it was a perfect recipe for old people to shift and send the car through the garage wall. Lol. The classic issue of when customers want something stupid, do you build it?
Re:Why Carmakers Can’t Transition to Newer Chips by SV_BubbleTime on Saturday October 02, 2021 @10:11PM (#28733953)
Not entirely a farce.

The PCM (engine controller) that a university audit got access to had 12,000 global variables. Their conclusion was it was not possible to prove either way.

There was a definitely real issue with floor mats getting the pedal stuck. I don’t know enough background on it past the audit that was done.

Re:Why Carmakers Can’t Transition to Newer Chips by wrycoder on Saturday October 02, 2021 @01:06PM (#28730188)
Easy to do. I stepped on the accelerator instead of the brake once. First impulse is to step harder, until you realize what’s going on. If your realization is slow, bad things can happen.

If bad things happen, the tendency is to blame someone else.

Re:Why Carmakers Can’t Transition to Newer Chips by andi999 on Saturday October 02, 2021 @01:49PM (#28730490)
One solid step on the accelerator easily let's bad things happen below 1s.
Re:Why Carmakers Can’t Transition to Newer Chips by rstuart4133 on Monday October 04, 2021 @06:10AM (#28744943)
I followed the accelerator-gate thing fairly closely, and I came out pretty convinced it was a computer failure. If it wasn't Toyota's floor mats were many times more likely to jam the accelerator than any other make or model.

There was a plausible root cause - a bit flip in the CPU. It was proved such flipping the right bit would cause uncontrolled acceleration that characterised each event.

I don't agree Toyota was guilty of shoddy work, or cost cutting. At worst, there were guilty of working some fairly shitty, hard to support code. (Someone below mentions 10,000 global variables.) If anything that shitty code just proves how dedicated Toyota was to testing something until until all the safety related bugs are gone, because despite some horrid kludges like replying on watch dogs resetting the thing when it got stuck and a reset so fast most people wouldn't notice it, despite the intense scrutiny of the code no one every found a safety issue with it. Toyota was well aware of a electrically noisy area like a engine bay could cause bit lips, and defended against it. Every variable was stored in two places in RAM, and on use they were always read and compared, and if they differed it was reset.

Sadly for Toyota they used a proprietary ECU and OS provided by NEC. NEC didn't let their customers look at their proprietary stuff. NEC didn't defend against bit flips. And it turned out a bit flop in a task ready bit could cause that task to never be scheduled again. If that task was supposed to turn off the cruise control acceleration, then bingo.

I have no idea what changes Toyota made in response to this mess, but if I was to hazard a guess it would be when it comes to software, they demand their supplies open their source to them.

Re:Why Carmakers Can’t Transition to Newer Chips by WalterBright on Saturday October 02, 2021 @02:21PM (#28730761)
The pedals are close together in my car, and a couple times I have hit the accelerator rather than the break. But I knew immediately what was wrong and adjusted.
Re:Why Carmakers Can’t Transition to Newer Chips by radicalbyte on Saturday October 02, 2021 @12:42PM (#28730014)
It literally took me years to understand it - how can you accelerate by accident? Until someone mentioned that all of these cars were automatics.

But every automatic I've ever driven (not many - I prefer a clutch) moves forward unless you're pushing the break in. In the rest state, it's in motion.

The problem isn't Toyota, the problem is a broken system.

Re:Why Carmakers Can’t Transition to Newer Chips by mpyne on Saturday October 02, 2021 @12:52PM (#28730087)
That's a mechanical side effect of the torque converter used in automatics, which even at engine idle with no acceleration input is able to transfer power to the drivetrain.

The Toyota case was an instance of the car's engine control software unexpectedly commanding acceleration not requested by the user.

In principle it could happen on a manual car as well, but most of Toyota's vehicles in the U.S. are automatics.

Re:Why Carmakers Can’t Transition to Newer Chips by gedy on Saturday October 02, 2021 @12:55PM (#28730114)
People panic and jam the wrong (or both) pedals. (There are quite a few people who use two feet to drive automatics, one foot for break, other for gas..)
Re:Why Carmakers Can’t Transition to Newer Chips by lostlogin on Saturday October 02, 2021 @01:48PM (#28730486)
> There are quite a few people who use two feet to drive automatics

They are very irritating to drive behind. Some seem to keep pressure on the brake pedal, and the brake lights stay on as they accelerate. When they slow it takes longer to realise they are braking as the lights have been solidly on.

Re:Why Carmakers Can’t Transition to Newer Chips by frosted-flakes on Saturday October 02, 2021 @03:21PM (#28731214)
Are you sure they're not just driving a manual transmission car? I can keep my foot lightly on the brake and apply the clutch to accelerate, without touching the accelerator pedal (diesel engine has a lot of low-end torque). Not that I do this in practice, except in drive-through lines just for the fun of it.

In first gear I can reach 8 km/h, but it's possible to get all the way to fifth gear while idling (takes a long time though).

Re:Why Carmakers Can’t Transition to Newer Chips by swiley on Saturday October 02, 2021 @03:08PM (#28731120)
I thought you would fail most driving tests doing that.
Re:Why Carmakers Can’t Transition to Newer Chips by Zak on Saturday October 02, 2021 @08:52PM (#28733587)
Perhaps, but left-foot braking is a useful technique, and common practice in some forms of racing.

In street driving, the main application is being ready to brake while driving normally. It is much faster to brake with the left foot hovering over the brake pedal than by moving the right foot from the throttle to the brake. Of course covering the brake pedal with the right foot precludes driving normally on a flat road or uphill.

This should of course be practiced in low-risk situations before being attempted in high-risk situations.

Re:Why Carmakers Can’t Transition to Newer Chips by gedy on Sunday October 03, 2021 @07:43PM (#28741546)
True but these are definitely not race drivers I'm seeing, jumpy older drivers mostly.
Re:Why Carmakers Can’t Transition to Newer Chips by AlfeG on Saturday October 02, 2021 @01:30PM (#28730354)
Not sure how is this possible. Automatic cars almost always require You to push brake constantly if you not driving. You can't turn car on without pressing brake, can't change to drive mode from parking state without pressing brake. There should be something very broken in Toyota case.
Re:Why Carmakers Can’t Transition to Newer Chips by andi999 on Saturday October 02, 2021 @01:51PM (#28730511)
Automatic handbreak at a traffic light?
Re:Why Carmakers Can’t Transition to Newer Chips by rectang on Saturday October 02, 2021 @11:55AM (#28729589)
From earlier discussions here (https://news.ycombinator.com/item?id=9643551 "10,000 global variables"), Toyota's conservative, arguably antiquated approach to software architecture wouldn't necessarily prove reliable as that software evolves.

Trying to assess whether thousands of global variables are still playing nice during a major rewrite to accommodate a new chip would be definitely be difficult and time consuming!

Not that a fast-and-loose approach is ideal, either.

Writing reliable software in the context of an organization is hard.

Re:Why Carmakers Can’t Transition to Newer Chips by finnh on Saturday October 02, 2021 @01:02PM (#28730156)
10K global variables sounds insane, until i realize "oh, huh, we have that too, we just call it _config_".

Almost every place we would have a constant (tuning parameters, etc) we instead have a configurable value with the likely default declared in code, but all overridable in config. Managing config can be a hassle, but the number of times we've merely had to tweak a value rather than roll a new build pays for itself every day.

We have thousands of such "global variables"... of course they are read-only, so aren't used to share state.

If Toyota is doing that: nbd. If they are using them to share state ... god have mercy on their souls.

Re:Why Carmakers Can’t Transition to Newer Chips by tremon on Saturday October 02, 2021 @01:26PM (#28730323)
I always interpreted the "10K global variables" to mean 10K directly accessible, heap-allocated symbols. It's a code reek. If you use a configuration object or other abstraction, the number of accessible variables may not change, but their scope and access method does.

It's a matter of interpretation I guess, but I would not classify a wrapper object (like .Net's ConfigurationManager singleton) as "10K global variables" even if the accompanying config contained 10K items, or if the ConfigurationManager backing store was preallocated in the data section of the binary.

Re:Why Carmakers Can’t Transition to Newer Chips by delfinom on Saturday October 02, 2021 @01:38PM (#28730401)
>I always interpreted the "10K global variables" to mean 10K directly accessible, heap-allocated symbols. It's a code reek.

Which to me on an old _accelerator_ design is suspect because that's alot of heap for the micros that would have been used back in the day. This isn't a Linux system. It was at best a micro with like 8KB of RAM. (I'm not actually sure what it is but there's no way it was impressive).

Re:Why Carmakers Can’t Transition to Newer Chips by rectang on Saturday October 02, 2021 @07:23PM (#28733058)
From the article referenced in that earliser discussion: https://www.safetyresearch.net/toyota-unintended-acceleratio...

> Other egregious deviations from standard practice were the number of global variables in the system. (A variable is a location in memory that has a number in it. A global variable is any piece of software anywhere in the system can get to that number and read it or write it.)

However, that was from the article author explaining the testimony, and not the testimony itself. It's not totally clear whether the variables were writable.

I would have guessed they were statically allocated rather than heap allocated, but what really matters is whether they were `const` — and they probably weren't `const` because otherwise this testimony wouldn't have rung true:

> "And in practice, five, ten, okay, fine. 10,000, no, we’re done. It is not safe, and I don’t need to see all 10,000 global variables to know that that is a problem," Koopman testified.

Re:Why Carmakers Can’t Transition to Newer Chips by rightbyte on Saturday October 02, 2021 @01:51PM (#28730521)
If they used Simulink, the model output and input, aswell as state, are global variables when generated to C in some settings.
Re:Why Carmakers Can’t Transition to Newer Chips by pokerhobo on Saturday October 02, 2021 @12:47PM (#28730049)
See https://www.youtube.com/watch?v=w5c5KzpamiM by someone who worked for a number of auto OEMs including Tesla where he explains how Tesla does agile hardware
Re:Why Carmakers Can’t Transition to Newer Chips by ngrilly on Sunday October 03, 2021 @12:35PM (#28738405)
I watched the video. Thanks for sharing. Powerful approach. But wondering how close it is from reality or not. Would be interested to know more.
Re:Why Carmakers Can’t Transition to Newer Chips by panick21 on Sunday October 03, 2021 @03:39PM (#28739906)
I would suggest you watch the Munro Live videos where they disassemble and analyses cars. This company has been doing this for decades and recently started making some videos.

The changes in Tesla vehicles are absurdly fast. They disassembled original Model 3 and then China Model 3, and since then the refresh 3 and the Y.

Recently they showed the new Model 3 LFP (Lithium Iron Phosphate) and the electronics and how it was integrated is already different again.

Re:Why Carmakers Can’t Transition to Newer Chips by 01100011 on Monday October 04, 2021 @11:39AM (#28748106)
How does that work out for maintainability? Is Tesla going to maintain parts inventory long enough to support owners for the lifetime of the vehicle(15-20 years?)?
Re:Why Carmakers Can’t Transition to Newer Chips by agumonkey on Saturday October 02, 2021 @01:05PM (#28730179)
> That obviously allows them to out-compete other auto manufacturers who are more aware of things like product liability

A lot of this era comes down to this. You have a legacy industry with tons of regulations, then a new guy comes up, steps on all the lines, and convinces people they're smarter for doing more for less. (up until regulations come back in the equation).

Re:Why Carmakers Can’t Transition to Newer Chips by panick21 on Sunday October 03, 2021 @03:44PM (#28739935)
Its very easy to claim that everybody else is not following regulation and that the only reason you are losing is because you do. Its much harder to prove.

If anything, GM had more problems and failures of their EVs so far. So the claim that Tesla is ignoring liability and doing much higher risk development is literally just an accusation based on nothing.

In actual fact, GM is spending 10s of billions buying back every single Bolt and they have been forced to shut down the line. At the same time Tesla had no such issues.

So, how about these people actually prove or substantiate in some way that the new comer ignores regulation or quality. Specially when, they themselves have a worse record.

Re:Why Carmakers Can’t Transition to Newer Chips by agumonkey on Sunday October 03, 2021 @05:54PM (#28740830)
Oh in that case I was more thinking about Uber and the likes. In Tesla case, the only glaring problem is 'autopilot' the rest I have nothing to say.
Re:Why Carmakers Can’t Transition to Newer Chips by ahepp on Saturday October 02, 2021 @05:39PM (#28732321)
Isn't the fact that Toyota lost this case damning to traditional automotive software development practices, rather than evidence of their importance?

The traditional players are already doing a bad job trying to write safety critical software the way things are now.

Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @11:32AM (#28729390)
It is very troubling development when doing something so trivial even requires a computer.

That's a matter readily solved by a PID controller made of a few dozen 74XXX parts. Possibly made n-times redundant.

Even a more fancy LP solver probably wouldn't need a fully fledged computer.

Re:Why Carmakers Can’t Transition to Newer Chips by HeyLaughingBoy on Saturday October 02, 2021 @12:24PM (#28729839)
Let's start by assuming that the engineers are at least basically competent, shall we?

I mean, I could implement a PID controller without any 74xxx logic at all: a basic op-amp, a handful of resistors and capacitors and boom I'm done!

But there's a reason that engineering doesn't do that these days and it's not that engineers don't know how. My PID control built from an opamp? In 2021 that's almost always a stupid idea. We use computers because doing it digitally has many advantages. We don't use 74xx (or any other logic family) for this because microcontrollers are far more flexible, allow for behavior changes without reworking hardware, allow inventories to scale (the same component can be used in hundreds of products) and more reasons I won't detail.

The reality is that in 2021, often the simplest, most robust and cost-effective way to do something trivial is by using a computer to do it.

Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @04:57PM (#28732012)
> The reality is that in 2021, often the simplest, most robust and cost-effective way to do something trivial is by using a computer to do it.

Very much not. Complicated MCUs are a very risky single vendor supply, and as we see now, people are now paying for an engineering overkill.

74xxx are available in every shape, and form, from dozens of suppliers.

Re:Why Carmakers Can’t Transition to Newer Chips by kortex on Saturday October 02, 2021 @03:09PM (#28731122)
Ok, lets assume for a moment that throttle can be modelled by a PID plant (it can't) - is the circuit temperature stable? You don't want the characteristics changing as the engine. Now you need a compensator circuit. What about power supply stability and noise? Car power busses are hella noisy, due to alternator and spark coil. Now you need some serious conditioning and filtering. What about knocking? Modern ECUs adjust parameters on knock detection to reduce the damage from pre-ignition. Gotta put in a control system for that.

Repeat for manifold air temp, exhaust temp, emissions, rev limiter, etc., and as you mention, make that 3x for redundancy. Now you have hundreds to thousands of components, in a high noise, vibration, and temperature environment, and you have something which is about as efficient as an 80s car. And you can't as easily simulate it cause it's analog.

Or just use some digital chips and simulate all the tuning.

Re:Why Carmakers Can’t Transition to Newer Chips by SkyPuncher on Saturday October 02, 2021 @11:39AM (#28729461)
It's really easy to over react because of the silicone shortage, but in many cars these chips are replacing physically manufactured parts or significantly increasing efficiency in a way that isn't possible with physical based components.

Electronic fuel injection is a _great_ example. Much of modern fuel efficiency stems from the fact that an engine can accurately control fuel in the cylinder based on a bunch of factors. Not only does this system require physically fewer materials, it uses less gas (in turn saving production effort).

Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @11:54AM (#28729586)
I think you are misunderstanding me.

What I mean under a computer is a Turing complete machine. A circuit just doing some LP solving, or PID is not necessarily a computer.

Re:Why Carmakers Can’t Transition to Newer Chips by rcxdude on Saturday October 02, 2021 @03:16PM (#28731180)
Very little applications strictly need a turing complete machine. However microcontrollers are ubiquitous because they are so flexible. One chip does the job of many, and without needing to be specialised, allowing all applications to take advantage of the economies of scale in semiconductor manufacturing. (Also as pointed out here you drastically underestimate the complexity of a modern ECU)
Re:Why Carmakers Can’t Transition to Newer Chips by SkyPuncher on Saturday October 02, 2021 @01:30PM (#28730346)
By that explanation, I actually 100% confident I'm understanding you correctly.

Most of the functionality of these chips can be represented in some form of hardware. However, that hardware is often much more expensive, significantly less flexible, and likely significantly bulkier.

Re:Why Carmakers Can’t Transition to Newer Chips by avianlyric on Saturday October 02, 2021 @11:39AM (#28729466)
There’s nothing trivial about a modern internal combustion engine. The throttle control system is doing quite a bit more work than just opening and closing a physical throttle valve.
Re:Why Carmakers Can’t Transition to Newer Chips by KZerda on Saturday October 02, 2021 @03:57PM (#28731531)
Okay, so you've designed it. Now, make sure it works with the dirty electrical signal of a typical car's power bus. Then make sure it fits in the space requirements of under the car's hood, or in the door, or any of the other tight places that these embedded systems go. Then make sure that it's verified to act over several years of vehicle life. Then, make sure your suppliers will guarantee you that they won't discontinue the part for at least 10-15 years because of legal requirements for spare parts. Just throwing discrete logic at the problem doesn't always help.
Re:Why Carmakers Can’t Transition to Newer Chips by dharmab on Saturday October 02, 2021 @11:45AM (#28729509)
ECUs are simpler to build than the mechanical components they replaced and do things impossible to do mechanically (given the space and weight limits of a car).

Jadon Cammisa has a great series on this stuff. Here's just one episode on one topic, drive by wire throttle control: https://youtu.be/gKsCHx5NOMM

Re:Why Carmakers Can’t Transition to Newer Chips by joking on Saturday October 02, 2021 @02:50PM (#28730995)
Simpler to build, and even simpler to overbill for them. Is insane to charge over 1000$ for some replacement logic board.
Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @11:51AM (#28729564)
Most drive by wire systems I seen are nothing, but a simplest closed loop PIDs.

It's very close to what you are taught in the "How to write a PID controller" class without much extra creativity.

Re:Why Carmakers Can’t Transition to Newer Chips by dharmab on Saturday October 02, 2021 @11:56AM (#28729599)
Have you looked at any vehicle from the past 3-5 years? I own one with drive by wire and you can feel and hear it reacting to variables when you push it to the limits (either in inclement terrain or on a closed course). The linked video has specific video examples from production vehicles as well.
Re:Why Carmakers Can’t Transition to Newer Chips by kevin_thibedeau on Saturday October 02, 2021 @12:09PM (#28729693)
Deciding how much fuel will be injected each cycle is not just a simple PID. The throttle body control may just be a basic servo (although it probably isn't) but the system controlling it is more complicated.
Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @06:12PM (#28732575)
A separate circuit to map fuel/gas ratio for a given sensor input is also not a rocket science.
Re:Why Carmakers Can’t Transition to Newer Chips by tziki on Saturday October 02, 2021 @01:50PM (#28730500)
Ah the classic HN "just use this things I just came up with".

https://xkcd.com/793/

Re:Why Carmakers Can’t Transition to Newer Chips by cycomanic on Saturday October 02, 2021 @02:37PM (#28730904)
I actually believe programmers/software engineers are the new physicists in this regard.
Re:Why Carmakers Can’t Transition to Newer Chips by GeorgeTirebiter on Saturday October 02, 2021 @04:51PM (#28731964)
So much speculation here. Let me set the record straight(er). (I worked in Tesla FW, left 5 years ago.) Tesla does use industry best practices. All code must pass MISRA checkers, code is modular, and reused when possible. We used all sorts of chips (that were auto qual) of many different architectures. We had extensive tools for e.g. stack monitoring, diagnostic readouts, and much more. If you move from, say, one ST ARM chip to another one in a similar family, the peripherals may be a little different, but generally work the same way (with maybe a few more or fewer features). So reworking the I/O drivers is work, but given the excellent layering of Tesla "body control" FW, it's really quite straightforward to pick a different processor from a given family. It's for sure true that if you went from ST ARM to Freescale/NXP ARM the peripherals are diff, so yes, more time would be needed to write the I/O drivers. But the effort ongoing when I left was exactly to make the appropriate SW generalizations so it would be possible to do exactly this.
Re:Why Carmakers Can’t Transition to Newer Chips by LennyWhiteJr on Saturday October 02, 2021 @11:19AM (#28729258)
To elaborate on this, the feature sets on these low level microcontrollers are no standardized. There is no common API for them to implement. Even chips coming from the same manufacturer will have different hardware capabilities, and although low-level drivers can abstract that way to a certain extent, there will always be differences.

The biggest challenge is when you need to update your firmware to use a microcontroller from a different manufacturer. Often times these chips are specifically chosen due to the set of hardware functionality they offer, and the firmware is written to take advantage of that from the start. The two are coupled.

Now you are forced to use a different chip, and the firmware that was written for a specific set of hardware now has to be modified for a new chip that may have a different feature set. Things fine print on how things like Analog to Digital converters becomes extremely important.

Re:Why Carmakers Can’t Transition to Newer Chips by Espressosaurus on Saturday October 02, 2021 @11:51AM (#28729560)
Even a single hardware iteration intended to be a drop-in replacement in some cases won't be due to relying on implementation-defined behavior that is not guaranteed by the datasheet and wasn't considered a constraint by the people designing the silicon. Sometimes it's a bug, sometimes it's just "didn't think that was important".

Either way, you're left with something where the saturation behavior changed, or it's no longer possible to read out a value without risk of corruption since they assumed it can be treated as write-only, or some other hard to find and debug problem.

Swapping out chips is an exercise in testing and risk management, and never should be done without care, even before we start talking about safety critical applications.

Re:Why Carmakers Can’t Transition to Newer Chips by rapjr9 on Saturday October 02, 2021 @09:02PM (#28733639)
I see this as a failing of microprocessor design. I/O should be standardized and there should be high level API's that do not change across chips or companies. MCU's are intentionally fragile in this respect to try to lock buyers into one MCU product family. It is absolutely stupid that I/O ports work differently for different MCU's and don't use a common API. It means every designer always has to reinvent the wheel when moving to a new MCU. This must have had a huge negative effect on product reliability and innovation. It's also why many products have moved to using Arduino's.

There is also a huge lack of improvement in MCU designs. Why doesn't my SPI bus autonegotiate everything? Why can't the serial port do the same? This should all be available in hardware as a standard feature of the ports. What a waste of decades of engineering talent to have to repeatedly troubleshoot everything at the bit level.

Re:Why Carmakers Can’t Transition to Newer Chips by BenjiWiebe on Sunday October 03, 2021 @12:08AM (#28734460)
Thank goodness they don't all use a standardized design. What if the standard design was the wrong one? You couldn't switch to a competitor with a better design!
Re:Why Carmakers Can’t Transition to Newer Chips by jillesvangurp on Saturday October 02, 2021 @11:42AM (#28729488)
Tesla is much better at writing software than most of their competitors. That's how they can adapt so quickly.

They also do a lot more in house than their competitors. That means they can optimize their development processes, and align with chip suppliers across different components. If you have to work with a multitude of suppliers that each ship their own hardware and software, life is a lot more complicated. Changes take years in such an environment. Even a simple thing such as over the air updates to software is still science fiction in a large part of the industry. VW famously struggled with doing that for the ID.3 only managing their first updates fairly recently.

Of course, Tesla is still affected by supply issues as well. They can't switch suppliers every quarter.

Re:Why Carmakers Can’t Transition to Newer Chips by IshKebab on Saturday October 02, 2021 @12:20PM (#28729800)
Are they better at writing software or do they just care less about how safety critical it is?
Re:Why Carmakers Can’t Transition to Newer Chips by coryrc on Saturday October 02, 2021 @01:12PM (#28730226)
I think you underestimate how poorly software development is done in traditional industries. Practice makes perfect and they mostly practice writing reports not software.
Re:Why Carmakers Can’t Transition to Newer Chips by hulitu on Saturday October 02, 2021 @02:44PM (#28730956)
It depends. If you want to sleep well at night you take care. Of course if you are VW you take risks.
Re:Why Carmakers Can’t Transition to Newer Chips by coryrc on Saturday October 02, 2021 @04:15PM (#28731682)
Taking a long time doesn't mean you've done more useful work.
Re:Why Carmakers Can’t Transition to Newer Chips by hulitu on Saturday October 02, 2021 @06:17PM (#28732602)
But a longer testing can find more bugs.
Re:Why Carmakers Can’t Transition to Newer Chips by coryrc on Saturday October 02, 2021 @06:46PM (#28732782)
So can a shorter one.

(In a box at 120°C for a day is roughly equal to a thousand days at room temperature).

Smarter not longer. Write in a memory-safe language and you don't need to pay people to maintain spreadsheets of memory allocations...

Re:Why Carmakers Can’t Transition to Newer Chips by kiba on Saturday October 02, 2021 @02:27PM (#28730810)
Agile does not mean less reliable. See Boeing versus SpaceX.
Re:Why Carmakers Can’t Transition to Newer Chips by filoleg on Saturday October 02, 2021 @12:51PM (#28730078)
It isn’t that their engineers are inherently better at writing software. The parent comment explained exactly why their organizational and supply chain structure allows them to be more agile and better at writing software and delivering it.
Re:Why Carmakers Can’t Transition to Newer Chips by hef19898 on Saturday October 02, 2021 @02:59PM (#28731046)
I personally would rank Tesla's Supply Chain to high, so.
Re:Why Carmakers Can’t Transition to Newer Chips by hulitu on Saturday October 02, 2021 @02:43PM (#28730942)
You cannot replace a Xeon with an Epyc without redesigning the motherboard. In reality is even worse. You replace a chip from ST with one from Renesas for example.
Re:Why Carmakers Can’t Transition to Newer Chips by JohnJamesRambo on Saturday October 02, 2021 @11:17AM (#28729228)
I feel like GM and Ford are at US Government and NASA size where getting any change through takes so long and so much middle management and red tape that it stretches to infinity.

I’m sure Tesla is more agile than that. For better or worse sometimes…

Re:Why Carmakers Can’t Transition to Newer Chips by mathattack on Saturday October 02, 2021 @11:23AM (#28729291)
The bigger the company, the more effort that’s needed to coordinate the parts. At some point one person can’t keep the whole in the head and has to lean on process. Tesla is small enough, and has a CEO that can keep everything in his head.
Re:Why Carmakers Can’t Transition to Newer Chips by ulfw on Saturday October 02, 2021 @12:17PM (#28729762)
Tesla has over 70,000 employees. I know people think Elon is god, but come on, he can't have "everything in his head". Tesla isn't some mom and pop shop.
Re:Why Carmakers Can’t Transition to Newer Chips by hulitu on Saturday October 02, 2021 @01:06PM (#28730183)
If this is true, stay away from anything Tesla does. I work in the industry. 2 examples: 1) you have to change a transistor with one from a different supplier, same characteristics. You need to do some HW engineering tests. If the transistor is part of a safety relevant function, you need to do also system, SW and safety tests. And then environmental and EMC tests. Of course you can tailor but you need a very good justification. 2) You change the microcontroller. You need new SW, new tools (emulators - takes some time to be delivered), new sourcing, new HW design etc. It is from development perspective a new product so you need testing (HW, SW, System, Safety) and design validation (environmental tests, EMC) , maybe more than one loop.And when everything is passed and sourcing is done (i.e. you can buy the component) you can start production.
Re:Why Carmakers Can’t Transition to Newer Chips by stefan_ on Saturday October 02, 2021 @01:16PM (#28730244)
What software can turn a MSP430 or 68 knockoff into a highly efficient power transistor? Take everything Musk says with some caution..
Re:Why Carmakers Can’t Transition to Newer Chips by AtlasBarfed on Saturday October 02, 2021 @11:23AM (#28729292)
I get that what Musk quoted is not a trivial task, and if accurate, is probably much quicker than OEMs and Big Auto could do since Tesla is presumably much better at software.

The article quotes Intel at 16nm, which is, what, 10 years from cutting edge process node? At this point mature OEMs and Big Auto should have been on a refresh process to auto-migrate forward the chips. The semiconductor industry is 40-50 years old now. And new generations produce better chips (cost, power use, performance).

As other comments say, it smacks of laziness and lack of forecasting.

Tesla has other advantages, since they are so much more vertically integrated, they can probably manage migrations a lot more easily and centrally.

Big Auto is more like "Big assemble OEM parts". OEMs make all the components, Big Auto just wants to screw them into place and wire them together. It's part of why they suck at software that integrates things: They don't make any of the components, and a dozen different departments order them from a hundred suppliers, so getting interfaces/protocols/specs is a lot more time consuming than for Tesla.

Re:Why Carmakers Can’t Transition to Newer Chips by echelon on Saturday October 02, 2021 @11:27AM (#28729344)
Why did car companies allow themselves to make such a strategic mistake? Shouldn't they be on a standard microcontroller architecture?

Why not even use ARM, X86, etc? It'd save them money at this point. And there wouldn't be a supply risk.

Re:Why Carmakers Can’t Transition to Newer Chips by HeyLaughingBoy on Saturday October 02, 2021 @12:32PM (#28729935)
Wouldn't really make any difference. The last company I worked for did pretty much everything with MCU's based on ARM Cortex-M.

All that shit's still not in stock anywhere. And remember that ARM, x86, etc. only defines the processor architecture. The I/O is far more important in a control application and I/O is anything but standard across platforms.

For one product we ended up buying a vendors entire supply and redesigning the product to use it, crossing our fingers that the supply chain would have unwound itself by the time we ran out of inventory.

Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @11:38AM (#28729450)
Tier 1 suppliers have an incredible amount of influence in that ecosystem, and Tier 1 suppliers have an incentive to not be easily replaceable. That'd be my guess.

I mean, it's an entire MASSIVE industry that's comprised almost entirely of truly commodity technology, and so you get all the perverse outcomes that happen when trying to "differentiate" despite being commodity by inventing ways to be "special" to drive lock-in. Interoperability only really benefits the OEM, and the OEM isn't the only part of the chain.

Re:Why Carmakers Can’t Transition to Newer Chips by to11mtm on Saturday October 02, 2021 @12:44PM (#28730025)
As others have mentioned, the peripherals/etc related to a specific model of microcontroller and how you work with them play a big factor.

But I'd also like to throw in:

- 16 years or so ago, the US side of the Auto industry was trying to steer towards PPC. Motorola/Freescale's presence in the market probably had a bit of a play in this, as well as ARM's then-status of 'not quite powerful enough to be future proof.' A StackOverflow post from 2012 [0] seems to indicate they did indeed standardize, whether they moved on from there is another question.

- Most Carmakers probably -don't- want to change designs outside of a refresh. There's a few reasons for this, including both external (updating documentation to repair network) and internal (when I worked at a place that did software/services for a US automaker, we had to submit pages of documentation/paperwork to change a couple of items placement/wording in a dialogue box.)

[0] - https://electronics.stackexchange.com/questions/26035/whats-...

Re:Why Carmakers Can’t Transition to Newer Chips by kevin_thibedeau on Saturday October 02, 2021 @12:12PM (#28729723)
Those processors aren't made on high reliability processes. You don't want your ECU built with the same media processor as the infotainment system.
Re:Why Carmakers Can’t Transition to Newer Chips by somehnguy on Saturday October 02, 2021 @12:37PM (#28729973)
Maybe I do! I've seen both fail just the same so it's not like ECUs are failure-proof or something.
Re:Why Carmakers Can’t Transition to Newer Chips by kevin_thibedeau on Saturday October 02, 2021 @12:54PM (#28730107)
Your radio dying won't kill you.
Re:Why Carmakers Can’t Transition to Newer Chips by somehnguy on Saturday October 02, 2021 @01:12PM (#28730217)
Correct, but you seem to have disregarded half my comment. ECUs are not failure-proof and fail all the time.

I've never heard of anyone dying due to ECU failure either..I'm not sure how that would even happen given all the critical systems on a car are mechanical first with electronic assist. So you can't lose steering, braking, etc. The worst that happens is you lose power, which is about the same risk as a subpar standard transmission driver stalling out (and can also happen in a number of different ways). Can you expand on how an ECU failing might kill you?

I would love if someone could elaborate on why I'm wrong instead of drive by downvoting. This isn't reddit.

Re:Why Carmakers Can’t Transition to Newer Chips by VLM on Saturday October 02, 2021 @03:09PM (#28731126)
Its easier and more realistic to kill the company via a recall.

Take for example the Boeing 737-MAX. Eh, its bigger, needs a little more elevator movement to simulate the older model, just flex the software so it can wiggle a bit more what could possibly go wrong?

Likewise, remember the VW Diesel emissions "scandal". You can nearly kill a company without actually killing anyone.

So, the specified ECU chip (which is no longer in stock) could output 40 mA to the gas tank vacuum solenoid so we spec'd the solenoid to draw 30 mA on the coldest day of the year, usually it draws much less. Got a substitute chip only rated to 20 mA usually it'll work fine, what could possibly go wrong? Until it burns out and the vacuum solenoid fails open and nationwide millions of gallons of "excess" gas evaporate per year from sitting cars. Harmless on an individual scale but on a nationwide scale its a lot of ozone... Insert yet ANOTHER $35B recall to replace all the ECUs for willful emissions violations ...

I'm just saying its not binary where either people die and it kills the company or people aren't even harmed and nothing bad happens at all. Plenty of "company killer" situations where "what could possibly go wrong" got the F-around and find out treatment.

Re:Why Carmakers Can’t Transition to Newer Chips by hulitu on Saturday October 02, 2021 @03:00PM (#28731058)
Because the architecture is not so important. What is important is what periphereals are available. And even if you have the same architecture you still need to test if you change something. And things change rapidly also in automotive. 10 years ago you had a 100 pin micro at 32Mhz clock with 64kb ram, now you have a 384 pin micro running atva couple of hundred MHz with 256 MB ram.
Re:Why Carmakers Can’t Transition to Newer Chips by vvanders on Saturday October 02, 2021 @11:58AM (#28729611)
There's an incentive for chip vendors to not standardize since it makes migration hard and drives vendor lock-in. The CPU cores are one part but equally important is the peripherals and external featuresets.
Re:Why Carmakers Can’t Transition to Newer Chips by HeyLaughingBoy on Saturday October 02, 2021 @12:33PM (#28729948)
That incentive might exist, but what really drives the lack of standardization is that every application has different needs, so you end up with a common CPU and wildly diverging configurations tailored to various applications.
Re:Why Carmakers Can’t Transition to Newer Chips by clairity on Saturday October 02, 2021 @11:41AM (#28729483)
i'd guess adding an abstraction layer (between a general purpose microcontroller and the custom interfaces it needs to support) is likely not worth the added complexity (and bugs), since cars are on development cycles of many years anyway (for the benefit of simpler software development, and the risk reduction of being able to swap out the microcontroller if need be).
Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @11:48AM (#28729537)
They actually theoretically have a thing for this already. It's called AUTOSAR (now AUTOSAR Classic). It's supposed to be a component architecture to write down the software against a framework that can be backed by different MCUs. Of course, in practice much of the underlying esoteria of any given MCU/board configuration bled up through the abstractions and/or produced custom extensions.
Re:Why Carmakers Can’t Transition to Newer Chips by RealityVoid on Saturday October 02, 2021 @11:55AM (#28729590)
And AUTOSAR is a nightmare of a framework where it's nigh impossible to understand what is going on because of the crazy abstractions.
Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @12:04PM (#28729661)
Indeed, it's a mess and the surrounding tooling ecosystem is a pile of weird Windows GUI tools of about the quality you'd expect for very expensive tools that do very little provided to a captive customer base. It's all very circa 1990s RAD-tool mania-esque still in many ways.

That said, we're working with some groups in some automotive companies who are breaking this mold rapidly.

Re:Why Carmakers Can’t Transition to Newer Chips by RealityVoid on Saturday October 02, 2021 @12:09PM (#28729695)
Whom, if you don't mind me asking? I would.love to see stuff change in this field.
Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @12:22PM (#28729820)
I can't upset the NDA Gods on this one, unfortunately. I can say one is a traditional OEM that you wouldn't necessarily expect to be the sort to take vanguard steps like this and the other is a newer OEM that's not as encumbered by tradition (though due to the supply-chain also can't rid themselves of it).

Shameless plug WARNING: we (https://auxon.io) are hiring for engineering, marketing, and BD if industrial & operational technology is your thing.

Re:Why Carmakers Can’t Transition to Newer Chips by VLM on Saturday October 02, 2021 @03:25PM (#28731258)
I never signed the NDA, although I follow the space distantly, and they went public on their own website a couple years ago with a list:

BMW, Bosch, Continental, Daimler AG, Ford, General Motors, PSA Peugeot Citroën, Toyota, and Volkswagen.

I always rooted for an older competitor GENIVI which (very handwavy in a general sense) boiled down to "make dbus great again". I just always have a soft spot for anything that replaces CORBA and DCOP. More or less GENIVI had the same players as AUTOSAR.

I believe AUTOSAR suffers from trying to do too much; GENIVI's "all you need is a compatible bus" is the minimum you need so simplicate and add lightness and that's what should win; doesn't really matter if that guy runs QNX and that other guy runs FreeRTOS as long as the busses talk; whereas AUTOSAR tries to own and control everything top to bottom which just ends up stifling any productivity.

Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @03:35PM (#28731333)
If you look through the "Adaptive AUTOSAR" literature and documentation that's out there you can find that enormous chunks of it are lifted straight from GENIVI's stack/specs.

However, GENIVI/Adaptive-AUTOSAR tends to serve a different function in the vehicle architecture. It's mostly cockpit and less control/platform. AUTOSAR Classic is still the champ on the MCU side of the house.

Re:Why Carmakers Can’t Transition to Newer Chips by jowday on Saturday October 02, 2021 @12:53PM (#28730096)
I mean they also just dropped certain feature, like radar on autopilot.
Re:Why Carmakers Can’t Transition to Newer Chips by kube-system on Saturday October 02, 2021 @12:38PM (#28729985)
CPUs aren’t the only silicon out of stock right now. Most silicon doesn’t even run software.
Re:Why Carmakers Can’t Transition to Newer Chips by rootusrootus on Saturday October 02, 2021 @03:12PM (#28731153)
That’s a fancy way of portraying big tech debt. They will pay for these decisions later.
Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @11:15AM (#28729217)
ARM M family cores can run each other's code more or less.

Only the libraries for I/O need to be rewritten.

In some cases, there are drop in replacements (Gigadevices STM32 clones)

Re:Why Carmakers Can’t Transition to Newer Chips by pwg on Saturday October 02, 2021 @01:36PM (#28730388)
Except that in some cases, the automakers are not using a CPU with external interface hardware, they are using microcontrollers similar to the PIC series, example here: https://ww1.microchip.com/downloads/en/DeviceDoc/40300C.pdf (Note, I'm not suggesting they use these exact chips, this is just an example of the level of onboard integration that is available for micro-controller chips).

Single chip system, with built in analog comparators, timers, signal capture and PWM generation module, serial UART, etc. I.e., a whole "system on a chip" with the external world interfaces already built into the chip. Changing one of these for an ARM CPU with external analog comparators, timers, PWM modules, serial UART's, etc., is a redesign effort, not just a "change the chip" effort. If the clock speed possible via the internal clock oscillator is sufficient, then this chip needs only +5V and ground (plus programming) to be able to interface to and control some external analog or digital equipment.

Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @11:18AM (#28729245)
Are there even any ARM Cortex-M chips that are ASIL-B rated or better?
Re:Why Carmakers Can’t Transition to Newer Chips by im_down_w_otp on Saturday October 02, 2021 @11:33AM (#28729401)
Looks like the Cortex-R52 and Cortex-R5, a CPU and MCU, respectively both have been ASIL-D (the highest rating) qualified. Which is fantastic frankly. There's a bunch of legacy PPC, MIPS, and TriCore tech that's just miserable to work with because of their ancient and/or bespoke & proprietary toolchains. So, really the automotive industry lacks excuses that I would buy for why they're not moving forward onto new platforms other than the institutional inertia and supply-chain entanglements that its prioritizing instead.
Re:Why Carmakers Can’t Transition to Newer Chips by TaylorPhebillo on Saturday October 02, 2021 @11:24AM (#28729303)
I think the Cortex-R chips are more targeted here- I think the V8-R chips are designed specifically for automotive use, so I assume they have appropriate ratings.
Re:Why Carmakers Can’t Transition to Newer Chips by baybal2 on Saturday October 02, 2021 @11:27AM (#28729343)
There are very lazy car companies which simply specify "automotive certified" car chips for everything, including MCUs running window switches. So, don't be surprised $20 ARM-R based MCUs being used to do something trivial like driving window motor.

I seen a few dashboard where there is an STM32 sitting connected to a single button, whose only duty is to register a key press, and burp something on the CanBus in response.

Re:Why Carmakers Can’t Transition to Newer Chips by coryrc on Saturday October 02, 2021 @01:19PM (#28730266)
I guarantee you no one is running $20 MCUs in trivial applications (in normal times). They're very cost-conscious.
Re:Why Carmakers Can’t Transition to Newer Chips by kortex on Saturday October 02, 2021 @04:41PM (#28731898)
A) I doubt you need a $20 component to register a key press and do some canbus IO

B) If you did have a $20 microcontroller for Canbus control of a window motor driver but it saved $19 in extra wiring/labor (driver controls usually route to all windows), provides reliable debounce, automated one-push-to-open, and allows things like holding keyless lock to close all windows, it's totally worth it.

Re:Why Carmakers Can’t Transition to Newer Chips by hulitu on Saturday October 02, 2021 @02:52PM (#28731004)
Every component ( resistors, transistors, microcontrollers, etc ) must be Automotive qualified (AEC-Q ). That's how you have a minimum standard. A button cannot communicate on the CAN bus that's why you need the microcontroller.
Re:Why Carmakers Can’t Transition to Newer Chips by sbierwagen on Saturday October 02, 2021 @04:49PM (#28731955)
A big chunk of this crisis was caused by car manufacturers being insanely focused on cost cutting. Doing obviously dumb things with BOM isn't exactly a calling card of the automotive industry.
Re:Why Carmakers Can’t Transition to Newer Chips by detaro on Saturday October 02, 2021 @11:22AM (#28729279)
yes. ARM sells appropriate designs, and e.g. NXP offers some chips.
Re:Why Carmakers Can’t Transition to Newer Chips by legulere on Saturday October 02, 2021 @11:43AM (#28729499)
That relies on I/O being written as replaceable units of code and not sprinkled throughout all of the code.
Re:Why Carmakers Can’t Transition to Newer Chips by jbverschoor on Saturday October 02, 2021 @11:18AM (#28729244)
Weeks? This has been going on for almost 100 weeks
Re:Why Carmakers Can’t Transition to Newer Chips by mkr-hn on Saturday October 02, 2021 @11:24AM (#28729308)
I assume the alternative chips are still in short supply, but less so than their first choice. Everyone else is looking for alternatives too.