Well, rotating flywheels.
It amazes me just how much energy you can story in a flywheel. They're really neat devices.
(Some 480kg of mass in a ~600mm diameter configuration, at some 8-9000rpm maximum if memory serves)
It amazes me how hard it is to contain that kind of energy if it wants to get out. They're really terrifying devices.
Particularly when left in the hands of engineers who do not fully appreciate that any sufficiently rapid release of stored energy is indistinguishable from an explosion.
The balance bunker for load testing and balancing these at the shop I worked in was a pit 40 feet underground with 50 ton caps placed over top.
When the disk starts spinning all the liquid turns into essentially a solid, if there is a massive failure, simple venting could easily disperse the liquid 360 degrees or away from people, etc... (ie, a giant massive mist explosion)
I've worked with power washers that are dangerous when focused, but when the water is dispersed, it's practically harmless.
Is there some obvious thing I am missing here?
The "secret" to dense flywheel energy storage is in the equation: Energy = 1/2 * I * w^2
Where "w" is rotational speed in radians/sec, and I is rotational-inertia / rotational-mass. So you store the most energy by rotating it as fast as possible. 20,000 RPM stores 4x the energy of 10,000 RPM.
The issue with water, or really... anything outside of steel and other such incredibly strong materials... is that water doesn't hold itself together very well. As such, the RPM limit would be smaller than a steel-flywheel.
Indeed, steel is still not used in advanced flywheels, because some forms of plastic IIRC are superior at the kinds of stresses we're talking about. Thus, these plastic / composite material flywheels, while much lighter, can spin much faster.
Leading to more efficient energy storage.
-----------------
In effect, you need every part of the flywheel designed to hold itself together to reach maximum efficiency. Water is the exact opposite. Its a lot of mass but basically no ability to handle stresses. Solid Steel would be better and would spin faster.
There a few more relevant expressions for flywheels to express that you want them to be on the edge of breaking at maximum energy storage. http://large.stanford.edu/courses/2010/ph240/wheeler1/
Thanks for the additional math reference.
Of course, the rotor has to be able to handle increased circumferential and radial stresses resulting from increased omega. Carbon fiber (like T1000 grade) has extremely high tensile strength (lets you spin a carbon fiber rotor very fast) but low density. T1000 rotors store more energy at lower mass than steel (or any other metal) because of the proportionality to omega^2 and their high tensile strength.
But for commercial storage, it's really about the $/kWhr/mass in terms of the overall rotor economics. By that metric, it's hard to beat a composite rotor with E-glass as the major fiber. It's cheaper than carbon fiber by easily 100X and has about 30% to 50% of CF tensile strength. It's a bit denser than CF, but its cost metric is why most modern large energy storage flywheels use glass/CF hybrid composites and magnetic bearings (for high speed and zero wear).
In the old days, they made flywheels out of solid steel, then switched to piano wire (higher tensile strength). Then fiberglass, aramids and carbon fiber happened.
I want to ask then, based on other comments, that size can greatly improve the amount stored. So wouldn't a larger safer flywheel work in many places?
Also, my thought on the water as a solid, consider a steel wheel where instead of steel all the way through, put a liquid inside of a cavity. Since water doesn't compress, it would essentially be part of the same wheel, only safer in a collision? (arm-chair engineer)
I enjoy reading comments like yours so I can move on/let go of my from my silly pet ideas. :)
Well, consider that solid steel is considered too weak for a modern flywheel. So that questions why you'd be removing steel instead of adding more of it.
Modern flywheels spin really, really, really fast. Again, fast enough that modern solid steel is too weak. Newer composite materials are superior, but still need to be designed for maximum structural integrity.
Once a flywheel spins fast enough, it literally rips itself apart due to centrifugal forces. Any "cavity" weakens the structure and will break sooner.
At maximum speed (maximum energy storage) you want every part of the flywheel to be about to break. By introducing a non-structural material (liquid water), you have added mass but not the strength to get to higher speeds.
Imagine filling a bucket with water and spinning it around your body. All of the force to keep the bucket from flying away has to be held by the handle of the bucket. A better bucket flywheel would be all handle... Hopefully someone else can give you a better analogy.
Ok, that makes some sense... still not feeling it, but I can see the logic. Need more math in my education perhaps.
They're not good for long-term energy storage, since the fluid loses energy to friction and turbulence much faster than a solid-- think about how long a swirling vortex lasts in a cup versus how long spinning top can continue.
The thought being that since it's a safe medium to explode out, you could spin it faster than other mediums. The steel would just be a shell to hold the water, and therefore the containment vessel wouldn't have to be as robust, as the amount of steel that would fail would not be as much, and as soon as the water exploded out , the remaining steel would dramatically loose kinetic energy and possibly not even flyout.
Another comment said that 20k rpm would hold 4x the energy as 10k rpms. That implies that if you truly aren't afraid of the spinning medium hurting anyone, it would seem that water/steel hybrid would be better than solid steel, because you could spin it faster more safely.
I saw a Mazda RX3 Sport Sedan (a circuit racing class here in Australia ~25-30 years back) spectacularly blow a flywheel/clutch at the end of the main straight (at Oran Park) a long time back - it pretty much perforated all the bodywork in the plane of the flywheel - bonnet and both guards - as though it was a tearoff line on a set of stamps. We could hear bits landing 10+ seconds later hundreds of meters behind us in the parking lot. Depending on what port job he had, that could have been up around 12k rpm (if my vague 30 year old car modifying memory serves...)
I believe so, but compressor/turbine wheels don't have a lot of mass to them, so fragments don't usually escape very far if they blow up. I've seen a few compressor housings split, and the main damage is done to the engine itself really. I guess if your turbo was sitting high up and exposed, it might be a danger. Flywheels however just seem to fail more regularly from my experience.
(Also, yeah anything rotary powered deals with scary rpm's, haha!)
For anyone interested, here's some in-car footage of what we're describing here: https://www.youtube.com/watch?v=qOHUwL0zeXc and an image of what the result can look like: http://images.thetruthaboutcars.com/2011/04/LNJ11-BlowedUpPa...
The answer is to make the flywheel from a flexible kinetic lasso such that when it blows up, the forces tangle the parts in a manner that it is safely destroyed.
Imagine we take that 1 Tesla mass and turn it into a infinitely thin ring of infinite density material. Now we can calculate how fast it's need to be spinning to get all that mass doing "1000mph".
Lets make our infinitely dense 1 Tesla mass into an infinitely thin ring 1m in radius. Each point on that ring moves around it (2pir) circumference every revolution so ~6.3m per revolution. 1000mph =~ 440m/s SO we only need to spin this flywheel ay ~70 revolutions per second, just over 4000RPM.
4000RPM doesn't seem unreasonable...
(Note:I don't think your 1000mph stacks up though. The kinetic energy of a moving mass is 1/2mv^2. So the speed of a 1 Tesla mass object which has 10 times the energy of a 1 Tesla object doing 100mph is only sqrt(10)*100 closer to 320mph than 1000. My high school physics flywheel might only need to spin at 1500RPM...)
I remember it was one of a million things I read about in sciencey magazines that never went anywhere, but maybe it was the one I was most sad about never happening (at least so far)
The one product I do remember happening that I first read about back then was e-paper! That happened! Cool.
Just how much headroom is there? I'm under the impression that avoiding excessive heat is the key to battery longevity, so the question is whether or not this extra current increases heat levels to degrees that will have a measurable negative impact on the long-term capacity of the battery.
The single data point I have of 75k miles, once a week charging at 120kW from ~20% -> 60% shows very little degradation to the pack on our Model S.
Also, when it's warmer out I've seen warnings that in-cabin AC is lowered to divert to help cool the pack so I'm sure it's a question of thermals + number of parallel modules.
https://electrek.co/2017/05/07/tesla-limits-supercharging-sp...
FWIW you only see 120kW on the first ~35% of the pack and quickly tapers down to sub 100kW after that approaching home charging speeds for the last 80-100%.
The cells charge in parallel (there are on the order of 15,000 cells in car batteries), so at least right now the charger power is the constraint and not the battery chemistry.
The most power you'd ever really need to deliver is maybe 3-400 miles of range in 5 minutes. So at a point, that we are pretty close to, you don't really need to charge any faster.
Using Tesla as an example of our current charging constraints:
The Level 1 chargers that plugin into a normal outlet are at 2 kW.
In-home charging (Level 2) maxes out at about 17 kW, (close to the most the average house circuit can handle). An average gas station or retail parking lot is probably close to this. More likely it is down at 11 kW.
At Super chargers, the Model 3 can currently accept a max of 120 kW, and the chargers can put out a max of 200 kW.
Tesla has teased doing more, including a Megacharger for their semi's, that seems like it would work at more than 1000 kW. See https://www.teslarati.com/tesla-semi-megacharger-charging-po.... And also "Super charger V3" at something more than 350 kW.
Very roughly, kW is proportional to how much range you get for the amount of charge time. So 120 kW charging is about 10 times faster than 11 kW Level 2 charging.
Also very roughly, a Tesla Model 3 could charge it's 300 mile (75kWh) battery in about 5 minutes at a 1000 kW charging rate.
It is worth noting is that this particular need, dumping 75kWh of power in 5 minutes, will exist even as battery technology improves. Fast charging is not gating on electric cars because home and work charging works quite well. But there will be demand for fast charging as a convenience to electric car owners.
Good links and details here: https://en.wikipedia.org/wiki/Tesla_Supercharger
The battery storage facilities won't win any architectural awards as they are currently envisioned, but I can't wait to see whether this will actually work reliably; our first few attempts at electric ferries had some teething problems, mostly with the charge process taking too long to establish. The ferries run on a tight schedule; hence charge time dropped significantly as establishment was slow, and ferry batteries slowly depleted over the course of the day.
Anyway - 4.7MW translates into some quite massive shore power connectors, and they need to mate quickly and reliably - and when the weather gets rough, everything in the surrounding environment will be soaked in salt water. Interesting times.
Current or voltage? I thought Telsa Superchargers use higher voltage to charge quicker. More "pressure" (voltage) versus more flow (current).
To fully charge an 85 kWh battery in one hour, using a 480V supply, you would need to draw over 177A, assuming perfect efficiency. That is an absolutely ridiculous amount of current, and that would only charge one vehicle.
I'm not driving 400km every day so the grid will definitely handle it. But there is a lot of potential to reduce network costs if the charger negotiated with the grid.
Based on 120 kWh over 24 hours, your house, on a cold day, draws around 500 W. To fully charge a single 100 kWh battery, like you'd find in a new Model S, in an hour, you would need to draw 100 kW. That would be 200 times the average load on your house, drawn continuously, and that's only to charge one vehicle.
Something like a flywheel battery does have a lot of potential to save money, or even earn money, if it communicated with the grid. A large rotating mass could potentially store a lot of energy, and would be increasingly useful with the rise of renewable energy.
Many houses in cold climates using electrical heaters will actually use at least 2-3x this energy.
So yeah, 100 kW is quite streched, but we're not _that_ far from the power available in a home.
Still, that would be 20 times the average load on those homes, to charge a single vehicle. To move that power 100 feet, like from a busbar (I think, I'm not an electrician) to the charger would require a 3/0 AWG copper cable (which has a diameter of around 2 1/2", or 5.8mm). That cable costs around $2.59 a foot, or $259 to get power to that charger. That would be undersized, since I calculated it out at exactly capacity, and that price wouldn't include conduit (since the cable isn't direct burial) or installation.
Multiply that by three chargers, which I'd consider to be on the very low end of what a commercial installment would need, and you have quite a high demand for power. Five hundred amps at 480V is no joke. On the plus side, all this could spur adoption of renewable energy; with enough demand for power, investors will shovel money into renewable energy faster than it can even be used.
Flywheels are useful when you have a fixed installation with no weight constraints because you get certain benefits over LiPo cells, namely longevity. As a matter of energy density though, they are awful compared to LiPo and could never efficiently be used in a vehicle. Also, the gyroscopic forces would be such that it would be impossible to steer the vehicle.
That's a solvable problem, and has in fact been solved by F1 teams that have used it - Mclaren won two titles with their KERS equipped cars. The cars are demonstrably far from 'impossible' to steer...
At least if you drive a bit above the speed limit when commuting :)
The car still has a battery, this goes in the stationary charging system. It's used to increase the current when charging electric batteries. Most electric batteries can accept much more current than commercial electricity drops can provide. This system stores the current in stationary flywheels and then discharges it quickly when a car pulls up and plugs in.
So this provides something like a Tesla super charger, without having to call up the power company to rewire your gas station. They call it a "Kinetic Battery". In the video below, the CEO makes the claim that flywheels are much better for this because you can get many more discharge/charge cycles out of flywheels than with chemical batteries.
You can imagine that rewiring electric infrastructure all over the country would be quite a bit more expensive than just plugging in their system. You could also imagine a solar powered system (off the grid even) slowly being charged and then recharging a car in 10 minutes.
Cool idea!
Interview with CEO https://www.youtube.com/watch?v=YxRfPtYmTDE