Once that's enabled iOS will now bring up a super secret popup menu whenever you double tap the screen with three fingers. From the little popup menu go to Choose Filter -> Low Light and your screen will go dimmer than is normally possible. With this on and the normal brightness mode set to its lowest setting the screen can get quite dim indeed.
On an old LCD display there are some filters that do a linear/nonlinear mapping from 0->255 brightness to 0->64 for example, leaving the actual backlight at the same brightness. The downside is that colour banding and quantization start to get really bad - and 'black' starts to look very non-black.
However, when I three-finger triple-tapped, the menu showed up.
First is the zoom trick you’ve already described, then you can use the “reduce white point” display accessibility setting to apply even more darkening.
With minimum display brightness, low-light zoom mode and white point reduction set to 100%, the display gets very very dim. If you do this in normal lighting conditions, the display is basically impossible to see.
Now you can triple-click lock button to make screen dimmer. I have been using this for ages, saves your eyes in the dark.
On current iOS you don't need to be in zoom and double tap. The zoom filter is also available by tapping the "Zoom Filter" setting which is 6 items below the Zoom setting in Settings -> Accessibility -> Zoom. The double tap in zoom thing is there to make it easy to quickly change the filter while zoomed.
This and the white point setting void-pointer suggested are both controllable from Shortcuts.
There is a Zoom action that supports turning zoom on, off, or toggling it, a White Point action that supports turning it on or off, and a Brightness action that supports setting the brightness to a given percentage or asking for the brightness.
I just tried making two Shortcuts, "Low Light" and "Normal Light".
Low Light:
Turn Zoom On
Turn White Point On
Set Brightness to 0%
"Hey Siri, Low Light" then works. It does leave you zoomed, so you need to cancel that, but then you are left at 0% brightness and whatever Zoom filter you have set is in effect. "Turn White Point On" will set the white point reduction to whatever percentage you have it set to in the Reduce White Point system settings.Normal Light:
Turn Zoom Off
Turn White Point Off
Set Brightness to <ask each time>
That does what you'd expect. Siri asks you what brightness you want from 0 to 1. You can change that to a specific percentage if you don't want to be prompted.PS: This only fully works on iOS. On iPadOS zoom filters only work while actually zooming, and then only apply to what is shown in the zoom rectangle. On iOS the zoom filter applies when zoom is enabled regardless of whether or not you are actually zoomed.
The white point reduction does work on iPadOS so you do get some lowering of minimum brightness but not as much as on iOS when you can use both.
Samsung: https://www.samsung.com/au/support/mobile-devices/activate-e...
It's really dim, one time in the morning I thought the phone screen was off and it was just set to extra dim :-))
The main issue i think is that backlights tend to flicker at low brightness.
Human vision extends from about 10^5 cd/m^2 to 10^-5 cd/m^2 [1].
Typical backlights use something like PWM to modulate the brightness. That means you need to be able to scale your backlight by a factor of 10^10 to cover the whole human vision range. And if your CPU runs at 1 Ghz (10^9), then at the dimmest setting then even being on for a single clock cycle would be a flash every 10 seconds - clearly unacceptable, and even then, few backlight controllers could handle a 1 nanosecond pulse!
The fix is to use PWM combined with settable 'modes'. The modes could be 'bright light' (using all the backlight LED's, perhaps a few watts total), and a dim light mode, which uses just one LED through a high value resistor, of just a few tens of microwatts. Your two modes have a factor of 10^5 between them in brightness. So now the PWM on your CPU only needs a resolution of 10^5, which it can do.
[1]: https://www.researchgate.net/figure/Approximate-luminance-ra...
Uh, phones don't produce brightness that high. And the low range is "too low" for usefulness anyway. Your math is off by few factors
> And if your CPU runs at 1 Ghz (10^9), then at the dimmest setting then even being on for a single clock cycle would be a flash every 10 seconds - clearly unacceptable, and even then, few backlight controllers could handle a 1 nanosecond pulse!
CPU is not doing PWM, it's separate chip
And you can't realistically have more than few kHz of PWM frequency anyway coz of losses.
It's not really a technical problem in the first place, it's easy technically, just have 2 current sources, when you need low light you just PWM the low current one. And not "just putting resistor in series", that's extremely wasteful, or "single led" that would just not illuminate evenly.
My iPhone can go super dim, to the point that it's hard to see in a dark room. I use no special features.
Also, Kobo's eBook readers can go very very dim, and can be comfortably read in a zero light room. The max brightness I use is 29%-31%, dependent on lighting. My has a fixed light, but newer ones also adjust light temperature automagically, and much more comfortable to read (got one as a present for my dad).
I disagree with that opinion, though. I think it's one of the worst aspects of modern UI design.
Pretty nice and the only recent change I've made is making it re-evaluate the expression based on frequency of keystrokes (so 3 brightness-down keys in 1s becomes 9 evaluated decreases in brightness).
My Pixel 6 with an OLED screen doesn't work very good as a walking light in a dark room.
Your motion sensing kicks in before either your focus or dark vision, and even if you can't "see" it, your brain can get enough information to let you navigate.
I always laugh when I see competition over brightness. I cannot wait for e-ink monitors to improve and wish someone would make an e-ink phone.
Edit: Those settings might be standard on Android and not actually Pixel specific.
The biggest saviors to my longtime night reading habits, though, have been OLED and how many websites and ebook apps have competent true black dark modes.
What I find far more concerning is the brief mention in the article about the explosion in outdoor lighting, which is massively disrupting the little remaining wildlife we have left (and nevermind destroying any hope of a glimpse t a dark sky). And there is absolutely zero reason for it other than ignorant wrong ideas that it helps traffic accidents or reduces crime (it does the opposite). Calling it cargo-culting would be kind.
[0] https://health.clevelandclinic.org/do-blue-light-blocking-gl...
From flagship to cheap, it seems that if you're in a pitch black room and check the time on your phone, the light will illuminate the whole room, even on the dimmest setting.
I actually modded my phone by putting a resistor in the LED backlight circuit, which divided the brightness by 1000 - and it was still plenty bright at night (human eyes are logarithmic, so dividing the brightness by 1000 doesn't have as much visual impact as you'd expect).