Environmentalists can only wish that people were disposing of their electronics because of tin whiskers. Long lived consumer electronics needs a cultural overhaul more than it needs leaded solder.
Most current electronic devices are dumped much earlier than when they would fail due to the tin whiskers.
Many consumer electronic devices made 50 years ago are still usable without any problems caused by the aging of the soldering or of the semiconductor devices (but old electrolytic capacitors may have to be replaced). The electronic devices that are made now do not have any chances of such a long lifetime, with the exception of a few devices made for special requirements, e.g. military/aerospace.
The consumer devices which survived infant mortality, because they were free of manufacturing defects, had a negligible aging rate after that.
Modern electronic devices have far fewer initial manufacturing defects, due to automated production, but all age much quicker, due to very small component sizes, lower safety factors, surface semiconductor devices (MOS transistors) instead of bulk semiconductor devices (bipolar transistors), lead-free soldering and other similar changes in technologies.
Sounds like you should unplug it before you open it up.
But they could be easily repaired.
Of course nowadays something that simple could be a chip the size of a rice grain, power included. So that's something :)
Very true, however having full documentation would help nonetheless. My water heater electronic board cost over €250 to replace, although it contains less than €20 parts; a preprogrammed uC makes it impossible to replicate it. If it had public hardware and firmware documentation, someone could repurpose a similar but cheaper board or replicate the functions using a different rugged enough uC board, which would also likely bring down the retail price of the original spare part.
Citation required
As others have pointed out in this thread, reducing landfill waste from electronics is a much more complex problem and just adding leaded solder will not solve it.
Hence why I quoted the program name.
Storage was one of the areas I researched extensively. It was like that scene in the movie "Clear and Present Danger" [0] in that the answer was always the same frustrating one regardless of conditions:
Stochastic growth onset; 0 to 3 years; can't predict growth start or rate; can't stop them; they will penetrate almost anything practical you can put on a board.
And thermal cycling definitely accelerates whisker formation.
It's quite a nightmare, particularly when you are trying to figure out if this stuff can kill people you want to send into space. The only real mitigation is lead-based solder and coatings on components.
Cleaning? That can be both dangerous and highly ineffective. The whiskers are very strong due to their molecular scale. Mechanical brushing might fracture longer whiskers. Then you have the problem of ensuring that they don't go under devices or in-between contacts. The process would likely have to be repeated many times and include both manual and automated optical inspection as well as x-ray imaging (which might not be able to detect fine whiskers). And then there's the reality that you probably don't want to inhale these things at all.
So, off to the landfill we go. It is likely better to build a new board than to try to clean one. I can't even begin to compute the delta in carbon footprint between making a board with lead-based solder that will last decades and the "clean/green" RoHS board that is sure to end-up in a landfill (cleaning/fixing it is bound to have a massively larger carbon footprint that making a new board).
I assume for the really critical components, you'd need to avoid solder completely.
Heat everything up in an oven, the solder will reflow, and you might temporarily fix the board. It’s a similar idea to the Towel/Xbox 360 fix. I can attest to having successfully saved lots of random electronics this way.
All of this started with the eco-friendly alternatives to lead solder, I have a lot of old computer hardware and motherboards, and the hardware from the early 2000s is the least reliable, whereas most game consoles, motherboards, etc. from the 80s and 90s works flawlessly. To this day I swear by the leaded stuff for personal use, it flows better, doesn’t crack, and is superior in every way.
The bottom line is quite simple:
Tin whisker growth onset is a stochastic process. We cannot predict when it will start and we cannot prevent it.
Once they start growing it is almost impossible to contain them. They will poke through conformal coatings such as parylene and arathane. If they don't, they will buckle (coil-up) under the coating.
While buckling sounds like a desirable outcome, this could lead to shorting of adjacent contacts in todays fine pitch integrated circuits and components.
Growth rate can be in the order of 10 mm per year. This means that adjacent leads of something as mundane as a SOIC-16 package can be shorted by a tin whisker in 28 days or less.
The take away is: There's nothing we can do about tin whiskers that is 100% guaranteed to prevent growth or slow it down by a non-trivial amount. The only path that prevents their growth is to use lead-based solder. This is why, as an example, we would do such things as send out BGA's with RoHS compliant solder balls to be re-balled with leaded solder.
Time for a bit of a rant: All my work in this area led me to look at the RoHS initiative as yet another example of something that, while well intentioned, it will likely have precisely the opposite effect from what was intended.
The fact that lead-free solder is susceptible to tin whisker growth means that 100% of all consumer electronic products are ticking time bombs when it comes to failures. This means that all kinds of consumer, commercial and industrial electronic products will fail over time in ways we might not be able to explain. The reason for this is that nobody does deep forensics when products fail. There is no reporting from the likes of Apple, Samsung, LG, Visio, Sony and myriad other manufacturers on failure rates and causes. In fact, they might not even have this data as consumer, commercial and industrial users simply replace the devices as they fail and move on.
In other words, it is likely RoHS has caused --or will cause-- massively more garbage in landfills. As a simple data point, my 40 year old HP-41 calculator still works perfectly fine. It is impossible to imagine a RoHS-compliant calculator not ending up in a landfill way earlier than 40 years.
There was a bit of a movement to roll back RoHS around the time it was being enacted. Going up against many nations and politicians using "save the planet" to get elected proved impossible for those who rightly brought-up that the transition to lead-free solder required far more research before we fully understood the potential consequences.
It wasn't about not wanting to go lead-free, it was about making the move when the science and math indicated that it would not create the massive problem we now likely have on our hands. The data on electronics waste due to tin whiskers is probably impossible to find. It might not even exist. Which is a tragedy.
If you want to learn more about this, here are a couple of good links:
https://nepp.nasa.gov/whisker./background/index.htm
https://nepp.nasa.gov/whisker/reference/tech_papers/kadesch2...
https://www.google.com/search?q=tin+whisker&hl=en&tbm=isch
https://web.calce.umd.edu/tin-whiskers/