Heh, this is how I test these lamps as well. Also my camera has anti-flicker shutter which can detect it to thwart it by syncing the shutter release with flicker itself. It shows a warning when it detects is, as well.
Nice! Which cameras do this? And I wonder, how cheaply could a sensor be made to do this, that shows on the screen "there's flicker at 60Hz / 120Hz / 480Hz", if it didn't also need to be a great camera (e.g. it only captured at 480p)?
However, I wouldn't say "oh that's easy", because A7-III has two realtime DSPs, and one of them is directly responsible for things like real-time focusing, face/object/eye recognition and real time tracking, etc. So, I believe that DSP is handling the flicker detection as well.
...and A7-III is the "entry level" member of its generation. higher end models have more computing power than that.
The bigger issue with their top end cameras (i.e. the Z9 and Z8) is that without mechanical shutters you’re pretty stuffed if you have mismatched strobing from lights, which it turns out is very common. I’ve shot both an opera and a wedding recently where different lights were strobing at different incorrect speeds. It was particularly noticeable on a dimmable stage light in one production - I was sat there for about 10 minutes dialling in exactly the right speed to minimise it.
That'd be a pretty neat gig. "Fly me in to walk around your building and point out where your lights flicker for some people".
Unfortunately all those things are expensive so you rarely find such bulbs in the cheap bin at Home Depot.
I agree that throwing away a whole fixture (diffuser and all) because of compoment failure is wasteful, but I think LED tape is actually better than bulbs here: You can independently swap the PSU, the LEDs, and the mechanical parts.
Mind you, LED tape is pretty inefficient due to using standard voltages and then balancing current with resistors, but it's probably worth the repairability tradeoff for most.
I find the inefficiencies of the old system more manageable.
And to avoid ground loops, you also need fully isolated DC-DC converters. So you end up with the same power supply architecture as for AC-DC, saving only on buffer capacitors.
As an experiment, I converted my homelab to 48V DC to operate from the battery directly after my attempts at making a UPS failed. It works, but it's barely more efficient than doing a double-conversion.
I'm now redoing lighting in my house, and _there_ the DC power makes a lot of sense. I'm planning to use commercial-grade DALI, with tunable white setpoint. It uses true DC dimming, so there's no flicker whatsoever.
Is it, though?
You'd have to deal with additional wiring losses due to the lower voltage between the central rectifier and the devices, and the various individual devices would still need their own step-down converters to turn that 48VDC into something they can actually use.
On top of that: the central rectifier would have to be sized for peak load, while in reality the vast majority of the time it would be running at only a fraction of that. That's not exactly ideal for efficient operation. Individual power supplies can be designed specifically for a single device and operate at its sweet spot most of the time.
No. Everybody always complains about voltage drop. It's not a problem with LED lighting loads because they use so much less power. Let me prove it to you.
Assume we use the same 14-gauge copper Romex for our 48VDC lighting circuit that is already inside most home walls in the USA.
DC resistance of 14-gauge copper wire: 0.002525 ohms per foot.
Voltage drop over a circuit:
Current x Ohms/foot x Two-way distance
--------------------------------------
Nominal Voltage
Assume we're driving a 13-watt LED bulb (typical 100W incandescent equivalent) that is 50 feet from the supply.Current would be 13w/48v = 270mA.
.270A x 0.002525Ohms/foot x 100feet
-----------------------------------
48v
= 0.00142V
So the voltage drop is 0.14%. Any voltage drop less than 3% is considered
acceptable by NEC.Oh, but what if I want to run more than one bulb? Fine, let's do 10 bulbs on the same 14-gauge supply wire. Now the voltage drop is 1.4%. Still less than half the maximum limit.
And this is 14-gauge wire. What about 12-gauge? Well, that's 0.001588 ohms/foot.
.270 x 0.001588 x 100
---------------------
48
Now for 10 bulbs the voltage drop is eight tenths of a percent.Running LED room lighting in a standard American house at 48VDC on the 14-gauge wire that's already in the walls is completely doable.
Yes, we still need constant-current supplies in or near the bulbs, and those are not 100% efficient. Keep in mind also that some of that 13 watts we assumed above is for typical Home Depot 120VAC bulbs that have builtin rectifiers and [probably] crappy power supplies, so the waste power used by the constant-current supplies I'm talking about here -- which are simpler than the supplies used in Home Depot bulbs -- is probably less.
Which circuit does the blender connect to, or the kettle? The air fryer? The coffee machine?
How do I power a space heater to warm up a chilly room for the baby on a particularly cold and windy night?
Where does the window air conditioner connect that I need because my landlord is cheap and there's an intolerable heatwave?
The audio system? The guitar amp? The gaming rig? The vacuum cleaner?
I guess we plug that stuff into 3-phase outlets, which we'll need to have everywhere -- right? Fine.
---
So we've got other stuff, too, that's a little lighter. Phones, laptops. Lights. Stuff. That can all be made to convert 48VDC down to whatever it needs internally, but that conversion requires electronics that are local to the device. We haven't eliminated that at all.
But sure: It runs on 48VDC that is sourced from some manner of manner of central power supply. Neat, I guess?
---
But why?
It sounds like all we've really accomplished here is adding more wires, and more complexity.
I'm struggling to figure out how any of this is presents any meaningful advantage.
(Oh, I know! Let's keep our existing single-phase circuits, and add both 3-phase AC and 48VDC! Whooo boy! Now we've got a real clustefuck cookin'!)
3-phase.
> How do I power a space heater to warm up a chilly room for the baby on a particularly cold and windy night?
3-phase, and it's not obvious why you need the additional extraneous detail to explain why you want a space heater.
> Where does the window air conditioner connect that I need because my landlord is cheap and there's an intolerable heatwave?
3-phase, and again, it's not obvious why you need the additional extraneous detail.
> The audio system? The guitar amp?
DC, and DC.
> The gaming rig?
DC or 3-phase, depends on how much power it needs. Worth noting that some PC power supplies already draw more power than most 120V circuits should be carrying. (1500W is the commonly cited limit, and there are gaming rigs with larger power supplies than that.)
> The vacuum cleaner?
Depends on how much power it needs, and whether it's recharging a battery or running a powerful motor directly.
Because these discussions always come down to details, and I've found it beneficial to get them out of the way at the beginning.
> > The audio system? The guitar amp?
> DC, and DC.
Like here, for instance. No. Audio systems and guitar amps can be quite big.
> DC-to-DC can be substantially simpler and more efficient.
Except the whole system isn't DC-DC. There's still a central AC-DC component required, so at the end of the day:
We're still converting from AC to DC, and also added a DC-DC stage.
More parts, more wires.
This is already common. E.G. Computers currently do ac->12v dc (for in case transmission)->1vDC (for transistors). DC->DC is basically free.
Some early electrical installations, as in late 19th/early 20th century, used DC. Most have disappeared, with the exception of some surviving early elevators and perhaps some huge industrial motors, converted to running from a rectifier.
... and vehicles. DC is still very common in mobile installations.
Or just use your phone’s slo-mo feature to take a 240 FPS video (which then gets played back at 30 FPS). 60 Hz flicker becomes extremely visible. More than once I’ve noticed the strobe effect and then confirmed it this way.
“how many nerds does it take to buy a lightbulb?”
- Driverless, common as 120V chip-on-board light sources and as 120V strips. These are basically made out of diodes and resistors. They are awful. There are advanced designs that are slightly less awful.
- Self-contained devices with little driver ICs. You’ll find these in screw-in lamps and some integrated fixtures. They range from surprisingly good to awful, both in terms of flicker and dining performance. They have hazardous voltages inside (no isolation), so they’re essentially always supplied as a unit with 120V input. There are also 12VAC devices like this.
- Constant current light source (typically a few hundred mA at a voltage around 15-56V). The light source may be literally just an LED. The driver will be remote, possibly inside the same fixture, and the output may be NEC Class 2 or otherwise quite safe. These are the best, especially with a good driver. Flicker may be essentially zero.
- Constant voltage, usually in the form of tape, usually 24V but also seen as 12V and 48V. Sometimes there is a current limiting IC that gives equal brightness across a range of voltage. These are a bit less efficient than constant current devices. They can operate with no flicker at all at full brightness, and they can be PWM-dimmed. Trying to dim them by reducing voltage gives very inconsistent results.
The type of LED used has surprisingly little to do with how fancy or expensive a fixture is. Constant current drivers tend to show up only in fancier fixtures, but plenty of extremely expensive fixtures use awful light sources.
I've tried looking for studies to prove or disprove my experience. They should be easy to find, right? Humanity is replacing the entire planet's lighting with LEDs after all! Comment sections have been busy with people arguing about PWM flicker for years, probably longer. What is the best study you can find? For me, it is always the one from 1989 about pre-LED 60 Hz office lighting (that said it had adverse effects). Seriously...?
I wish I was a Bitcoin billionaire, for many reasons, but doing another study on flickery LED lighting seems like the lowest-hanging fruit of our entire civilization. I live in a country that is regulated to hell and back, and yet even our street lights flicker visibly, not to mention classrooms, children's bedrooms, and the screens that people stare at for hours every day. I don't get it.
I wish I was a Bitcoin billionaire, for many reasons, but doing another study on flickery LED lighting seems like the lowest-hanging fruit of our entire civilization. I live in a country that is regulated to hell and back, and yet even our street lights flicker visibly, not to mention classrooms, children's bedrooms, and the screens that people stare at for hours every day. I don't get it.
Humans are very sensitive to flicker in peripheral vision. Have them look at something across the room and then blow their mind.
(Note: easier with a phone, but doable with a laptop.)
Again: the USA is large, but other countries (usually with different systems) do exist.
The thing that makes that so insidious is that not everybody can easily perceive that.
(The reason why such flicker is common in cheap LED bulbs: they turn AC into DC using a half-wave rectifier, which just chops off half the AC wave. This is also why you can still see the effect in rooms lit by multiple lights, because the flicker is in sync, synchronized to the incoming AC.)
If you are building a space for other people and you are responsible for the lighting, please check for this. If you can't perceive it yourself, find someone who can.