Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by 0cf8612b2e1e on Monday October 20, 2025 @02:10PM
(#45647146)
Have diamonds found their way into other industrial cooling solutions? With the research into gem grade diamonds, I have been expecting cheap ugly synthetic diamonds to be used in more products. I have long joked that I want a diamond frying pan.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by rbanffy on Saturday October 25, 2025 @07:24AM
(#45702988)
The temperature of the blue flame on a stove should be above 1000 Celsius, well above what’s required to oxidise diamonds. They won’t catch fire, but your diamond pan will erode. Once you remove it from the flame, it won’t continue “burning”.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by kees99 on Saturday October 25, 2025 @08:33AM
(#45703410)
Would that >1000°C reach the surface though?
There are some heady boundary-layer effects and temperature/temp-conductivity gradient physics involved here. For simplicity sake, consider a plastic [1] bag full to the brim with water, held over open flame. Will bag melt (oxidize, erode)?
[1] polyethylene melts around 120-ish °C and ignites around 220-350 °C (sources vary)
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by mjevans on Wednesday October 29, 2025 @01:17AM
(#45742909)
The material would be 'fine', but I'm not sure how safe or effective it would be as I'm not a materials expert. Just considering the risk of the material. (Yeah, the material would be fine, is it safe and beneficial? That part of 'fine' I can't define.)
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by jrk on Saturday October 25, 2025 @09:24AM
(#45703719)
I think the point was not that gem-grade synthetic diamonds are ugly, but that, as industry masters gem-grade production, presumably below-gem-grade production (“ugly synthetic diamonds”) would become cheap enough to deploy in more engineering settings where diamond’s other unique properties were the key concern.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by Tuna-Fish on Saturday October 25, 2025 @12:48PM
(#45705255)
Large single crystal diamond, what is required for a nice transparent screen, is still quite expensive. This article is about polycrystalline diamond, which is not really that transparent, but is nearly as good at thermal conduction as monocrystalline diamond.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by KiwiJohnno on Saturday October 25, 2025 @11:00PM
(#45708808)
I have a Garmin with a sapphire screen. I've worn it every day for over 5 years, working on cars, in the garden, snorkelling on coral reefs.
In short, I my watch has NOT had an easy life. I've made no attempt to protect it or taken it off for anything except charging. There is barely a mark on the screen. A sapphire screen will be a hard requirement for my next watch.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by cassianoleal on Sunday October 26, 2025 @11:28AM
(#45712671)
I wear mine while rock climbing. The watch has been put through a lot of beating against all kinds of rock. I've already chewed through 3 straps on this watch. The titanium case is lightly scratched, but the screen is absolutely pristine!
This is my second sapphire Garmin, and it's absolutely worth the premium.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by rowanG077 on Saturday October 25, 2025 @02:27PM
(#45705977)
Even if that were cheap I don't think diamond would excel in this use case. It's of course extremely hard but I'd expect that it would be extremely prone to cracking. In addition the high index of refraction would make the diamond screen very reflective and you would need some fancy coating which of course wouldn't be as strong as diamond.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by IAmBroom on Tuesday October 28, 2025 @09:39AM
(#45732759)
I don't know why you expect it would be prone to cracking, but it isn't - or else a wedding ring would have a life expectancy shorter than the average marriage.
As for a reflective screen, the term for that is "shiny", and could be marketed as desirable - it signals that the owner has an expensive watch. It wouldn't interfere with use, unless the user was wearing a bright headlamp.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by gpm on Saturday October 25, 2025 @10:58AM
(#45704405)
3D printer nozzles, which is sort of the opposite (industrial heating products).
Part of the argument is that better heat conduction means that you can run the nozzle cooler resulting in less heat conduction to the cold side (above where you want the filament to melt) so I guess its "cooling" in a sense too.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by lightedman on Saturday October 25, 2025 @11:01AM
(#45704431)
Nothing new, Applied Diamond has made this stuff for several years and it is incredible. Imagine putting a 15w LED on a typical 20mm star board made of diamond - you do not need a heat sink. Just minor air flow over the package is enough.
A little unlike IEEE to be nearly half a decade out of the loop.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by trhway on Saturday October 25, 2025 @03:07PM
(#45706208)
naturally, graphite has similarly high thermal conductivity along the layer direction (which is basically graphene), and one would think that there should be some way to put such a thin layer of graphite/graphene on top (or inside) the chip to achieve similar results.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by akshatjiwan on Saturday October 25, 2025 @03:08PM
(#45706214)
I think what they have grown diamond on the transistor which then bonds to the substrate through a SIC interlayer.
From what I understand their idea seems to be that since most heating occurs at channels they act like hotspots and therefore it would be much better to drain away heat from them directly.
This is different from creating transistors on a diamond substrate.
Re:Diamond Thermal Conductivity: A New Era in Chip Cooling
by mutagenesis on Saturday October 25, 2025 @03:59PM
(#45706538)
What you linked is bonding a diamond substrate to the back of your IC. What's in the post is growing diamond lattice/features directly on your wafer. With the new way, you can get diamond closer to your heat sources, increase contact area, etc.
No idea if it actually matters. Is this a single digit percentage increase in thermal conductivity by messing with a finicky, temperamental process? I don't know. What the paper writers are proposing is under the limit of when transistor structures break down, but not by much.
As long as you don’t use it on a gas stove, you should be fine.
Or you mean it'll catch fire? Also not a concern. That is supposed to happen at a temperature well above anything useful for cooking.
Should be safe on electrical stoves though.
There are some heady boundary-layer effects and temperature/temp-conductivity gradient physics involved here. For simplicity sake, consider a plastic [1] bag full to the brim with water, held over open flame. Will bag melt (oxidize, erode)?
[1] polyethylene melts around 120-ish °C and ignites around 220-350 °C (sources vary)
There is also this, if you don't want to mess with open fire yourself:
https://www.youtube.com/results?search_query=boil+water+plas...
Not any more, their quality has increased recently. Not that I care, wife and I did without them during our engagement.
https://www.theguardian.com/technology/2014/feb/10/sapphire-...
In short, I my watch has NOT had an easy life. I've made no attempt to protect it or taken it off for anything except charging. There is barely a mark on the screen. A sapphire screen will be a hard requirement for my next watch.
This is my second sapphire Garmin, and it's absolutely worth the premium.
Ever consider carrying a protein bar or two?
As for a reflective screen, the term for that is "shiny", and could be marketed as desirable - it signals that the owner has an expensive watch. It wouldn't interfere with use, unless the user was wearing a bright headlamp.
Part of the argument is that better heat conduction means that you can run the nozzle cooler resulting in less heat conduction to the cold side (above where you want the filament to melt) so I guess its "cooling" in a sense too.
A little unlike IEEE to be nearly half a decade out of the loop.
From what I understand their idea seems to be that since most heating occurs at channels they act like hotspots and therefore it would be much better to drain away heat from them directly.
This is different from creating transistors on a diamond substrate.
Wait a minute, others have been doing this already: https://www.df.com/
How is this different?
See also: https://youtu.be/ggQKZDZsDec
No idea if it actually matters. Is this a single digit percentage increase in thermal conductivity by messing with a finicky, temperamental process? I don't know. What the paper writers are proposing is under the limit of when transistor structures break down, but not by much.