News for hackers. Stuff that matters.
Re:RadioShack’s new owner plots old comeback strategy by mortureb on Sunday September 03, 2023 @05:33PM (#37374829)
Everyone buys these things online or at Walmart. I think the best bet would be to try to remain small and capture the hobbyist market around electronics. Michaels already exists for art supplies, Home Depot can supply the screws but no one can really supply electronic components, PCBs, 3D printers etc.
Re:RadioShack’s new owner plots old comeback strategy by easton on Sunday September 03, 2023 @05:38PM (#37374862)
I mean, Micro Center exists in some areas of the country (the one near to me is literally next to a Michaels). The reason it’s not everywhere is probably because there’s not as much demand outside of big cities.
Re:RadioShack’s new owner plots old comeback strategy by bsder on Sunday September 03, 2023 @06:04PM (#37375030)
Cries in Fry's

Austin, of all places, really could use a Microcenter. I'm suprised they haven't put one there given they have them in Houston and Dallas.

Re:RadioShack’s new owner plots old comeback strategy by bigyikes on Sunday September 03, 2023 @06:07PM (#37375061)
Ha, we posted nearly identical comments at nearly the same time.

(Sorry, this comment doesn't add anything, but it was too synchronistic to not point out)

Re:RadioShack’s new owner plots old comeback strategy by bigyikes on Sunday September 03, 2023 @06:06PM (#37375046)
Begging for a Micro Center in Austin. They're in Dallas and Houston, so it surprises me we don't have one in the tech capital of the state.
Re:RadioShack’s new owner plots old comeback strategy by hellotheretoday on Sunday September 03, 2023 @06:08PM (#37375074)
I moved 2 years ago but before that I lived about 10m from a micro center for a decade. The hobbyist section in that time progressively got smaller and the selection was overtaken by branded expensive tools and kits. Like instead of just selling the cheap Chinese screwdriver set you could buy on Amazon for 9.99 they’d sell ifixit branded screwdrivers which appeared to be of the same build quality but with the branding and micro center markup were now 24.99 for the exact same set in terms of features. Or the solder practice kits where you could make a blinking heart from an op amp but for $20 when you could get it online for half that. Raspberry pis and arduinos and such were usually priced well but not always although sometimes they’d be on sale for very good deals. They’d sell hats, sensors, and such for them and those would be marked up considerably.

So it was the same problem as RadioShack; anyone who knew what they were doing would plan out a project and order what they needed online to save a considerable amount. What you’d buy would be if you forgot or broke something and needed to grab something asap and didn’t want to wait. That didn’t justify the space I suppose so they kept shrinking it down

What was really annoying was the stuff that would really be handy would be like small packs of passives. Like when I went to akihabara in Japan there was a market that sold small packet of things like resistors, capacitors, transistors, etc. in little baggies for few yen. And when I went to shenzen it was even better, you could get basically anything, smd or throughhole, in any quantity, but that’s kind of cheating ha. Micro center didn’t do this at any point I lived near it. They would only sell the big assortments so if you just needed a 100ohm resistor for an arduino project you had to spend $20 to buy 300 assorted through holes. Frustrating and pricey so id rather just go online and spend less to get a better and broader assortment.

Maybe if we actually do some real right to repair there might be some demand to justify but as is I think it’s just one of those niches that cannot compete with the internet and warehouse/logistic companies like digikey and mouser. There’s just too many skus

Re:RadioShack’s new owner plots old comeback strategy by spiritplumber on Sunday September 03, 2023 @06:42PM (#37375314)
how do you live 10 meters away from a micro center? next building?
Re:RadioShack’s new owner plots old comeback strategy by hellotheretoday on Sunday September 03, 2023 @07:14PM (#37375542)
10 minutes lol
Re:RadioShack’s new owner plots old comeback strategy by Sylamore on Sunday September 03, 2023 @10:15PM (#37376513)
I knew when I moved from AZ to NC I was going to miss Fry's (RIP), I should have checked to see if there were any micro centers within a 50 mile radius when trying to figure out where to move.
Re:RadioShack’s new owner plots old comeback strategy by thrtythreeforty on Monday September 04, 2023 @11:41AM (#37381556)
The Fry's next to my house died a couple years ago. It was time for it to go: it seriously sucked to walk through, and they hadn't updated any inventory since like 1990. Half the shelves were unapologetically empty.

This isn't limited to just this Fry's, either. I went to the one in Anaheim and it was also a bad time.

I would kill for a Microcenter to go in there. (I'm in Austin and it seems like we'd have plenty of the target market.)

Re:RadioShack’s new owner plots old comeback strategy by batguano on Monday September 04, 2023 @06:14PM (#37385634)
I live in the Bay Area, which is both big city, and heavily tech/maker, and I have never even heard of a Micro Center, much less seen one.

I miss RadioShack, and especially Frys when they were in their prime.

Re:RadioShack’s new owner plots old comeback strategy by fsckboy on Sunday September 03, 2023 @05:37PM (#37374853)
sell linux phones, etc

i spent my teen years studying and selecting electronic components from radio shack.

Re:RadioShack’s new owner plots old comeback strategy by dragontamer on Sunday September 03, 2023 @05:57PM (#37374989)
PCBs these days are like $5 per board from American makers like DKRed (Digikey's PCB service), with support for both 2x layer and 4x layer boards. Radio Shack will never be able to compete against DKRed (or OSHPark) from PCB making perspective. Even cheaper if you buy from China.

Radio Shack would be best as a board-level hobbyist group: selling Teensy, Arduino, Beaglebones, Rasp. Pi... as well as wires and common components.

A few wires, a standard board like Arduino, and some I2C or SPI components will be enough for most hobbyists, and "looks" far easier than a breadboard or PCB.

Re:RadioShack’s new owner plots old comeback strategy by smaudet on Sunday September 03, 2023 @06:17PM (#37375129)
I don't know, I think a shop that could offer both would be invaluable. I haven't heard of either of those PCB services, I'm not in the market to make them, but if I walk into a store and see this on offer, especially if someone is helping me to design etc, that could be a valuable service.

Wholesale mfgs will always be cheaper, but there is something to be said for a one-stop shop experience. I don't have to spend time learning websites or which tools they accept, I can just go to the store to get my idea built.

Re:RadioShack’s new owner plots old comeback strategy by dragontamer on Monday September 04, 2023 @02:18PM (#37383300)
You "can't" make a one stop shop for electronics, not at least how things are done right now.

Different projects will have different reasons for choosing transistors: maybe response time is maximally important. Maybe they're using the transistor in "linear" mode and would rather have a wide and consistent ohmic region. Maybe its a high-power application where breakdown voltage is most important. Maybe it needs to be ruggedized and they'll prefer protection diodes.

This is _JUST_ transistors. Every other part basically has this similar problem.

There's just too many important decisions per part. As such, modern nmos-transistor catalogs number in the thousands of parts in practice. The only way you get the right transistor is through online ordering through megastores (like Digikey) who can keep stock of all the hundreds-of-thousands of SKUs + have an online searchable database to help you find what you're looking for.

-------------------

So where Radio Shack could feasibly work... is by:

1. Shrinking the catalog down to "standard" generic parts that have wide applicability to many different projects. "Jack of all Trade" transistors, that aren't the best in any particular category but instead have nice behaviors across a large set of axis. This is just for a "keep in stock" perspective, for anyone who wants to "make an electronics project today" without waiting for the 5 to 10 days for typical shipping times for custom PCBs.

#1 means that Radio Shack (or other stores) can swap between transistors from different manufacturers as they come into (or out of) stock, or based on supply/demand. (Buying up excess stock from a factory on the cheap), etc. etc. But still organizing these parts to match various SKUs that match particular use-cases (ex: 3.3V logic NMOS).

2. Focus on physical attributes which benefit to coming into the store. Ex: Serving as a central point for expensive tool rental. An OEM-set of crimpers, for example the Harwin M20 series of Dupoint / Mini-PV clone connectors, has a $570 crimper. That's cheap for a store to hold in stock/rental, but a bit expensive for hobbyists.

Electronics in practice have _LOTS_ of $500+ tools (crimpers, 3d printers, laser cutters, etc. etc.) that really would benefit from rental-models. Furthermore, the tool usage scales well with wire usage in practice. (Ex: bulk ethernet cable is way cheaper than individual ethernet wires. If hypothetical-Radio Shack buys 10,000 ft. spools and has the nice $500 to $1000 crimpers to make your own wire in store, that's a good reason to come in)

-----------

With 4-layer boards so cheap in practice through online ordering, I really don't think "Hypothetical Radio Shack" can compete with that.

But give me a place to consolidate custom wire lengths + rental of those expensive crimpers, and we probably have a deal.

Re:RadioShack’s new owner plots old comeback strategy by tzs on Sunday September 03, 2023 @07:15PM (#37375544)
Don't most of those PCB places have a minimum number of copies of 3 or so? For nearly everything I've wanted to build I've only needed one. I end up using some kind of generic pre-made board like these [1] that mimics a common prototyping board or like these [2] that just have a bunch of groups of 3.

I really wish wire wrap was still common. Wire wrap was actually more durable and reliable than PCBs, and for a lot of hobby projects would be easier and faster than designing a PCB and having it made. I wonder if there is a big enough hobbyist market for a wire wrap revival?

[1] https://www.amazon.com/gp/product/B08SQ34KTC/

[2] https://www.amazon.com/gp/product/B07ZYTZ48N/?th=1

Re:RadioShack’s new owner plots old comeback strategy by dragontamer on Sunday September 03, 2023 @11:21PM (#37376828)
Well yeah, but back 15 years ago, it was $40 a board minimum copies 3 (or maybe $5 per board with $100 non-recurring engineering fee for a 2-layer board). Back when Radio Shack was big, people were doing hand-crafted PCBs by drawing out your traces with a permanent market and manually drilling holes into PCB-stock.

> I really wish wire wrap was still common. Wire wrap was actually more durable and reliable than PCBs, and for a lot of hobby projects would be easier and faster than designing a PCB and having it made. I wonder if there is a big enough hobbyist market for a wire wrap revival?

Wire wrap's main problem is that the wire-wrap sockets needed to make good, reliable contacts, are on the order of $1 each, so if you need to put like 5 chips on a board, you're well into "Might as well make a full custom 4-layer PCB", especially when you consider that SMT parts are so much more common these days.

But if you wanna talk Wire Wrap...

https://www.peconnectors.com/wire-wrap-sockets-and-headers/

https://www.vectorelect.com/terminals-wire-wrap.html

I know how to do that for sure. But... with PCBs so incredibly cheap these days, why bother? Its not like the $150+ days for a PCB, where $1 per socket, $10 wire-wrap boards and $0.10 per pin wire-wrap terminals were much cheaper than PCBs.

Today, its probably cheaper to order a PCB (even 3x copies) for $20 or whatever, and then throw away the other 2 copies, rather than getting into wire-wrap. The main benefit of wire-wrap is that if you've got a large collection of PCB parts + wire-wrap sockets, you can design and build a board today without waiting on stuff. But I wouldn't consider the wire-wrap way to be much cheaper.

--------------------

SMT for the most part has taken over through-hole in general (including wire-wrap). There's SMT-to-through hole stock boards you can keep, but I feel like learning KiCAD and just spending the $20 each time you wanna make a proper SMT board is the better idea.

The only exception is that through-hole can be built with stock parts in a "prestocked lab". If you want a "resistor book", a through-hole set of resistors + pre-made breadboard proto-boards is a good tool (especially if you have transistors, LEDs, Diodes, voltage regulators, and OpAmps).

You can solve a lot of problems by just combining simple things in a lab in half-an-hour... and then a few wires here and there to connect your doo-hicky to an Arduino or something is useful. Through hole remains a useful tool, although it'd be expensive to stock enough parts (resistor book, capacitor book, some trim-pots, LEDs, voltage regulators of various kinds, a few microcontrollers, breadboards, crimpers, connectors, etc. etc.) to get to this point.

---------------

Anyway, I think the through-hole community has largely settled upon two kinds of boards:

1. "Xacto-knife" boards, like Vectorbord 8019 (https://www.vectorelect.com/8019-1.html), where you're supposed to cut the traces that are too long and make them into individual lines as needed.

2. "Pad-per-hole" boards, like Vectorbord 8003 (https://www.vectorelect.com/8003.html), where you'its intended for you to spill solder between lines that should be connected.

These two techniques are pretty good, but you still need to create wires between points in practice. Wirewrap can serve the job. And arguably, solder+wire is generally considered a bad idea (the solder can internally break before the more flexible copper breaks, so you end up making a less reliable connection than what's possible with wire-wrap)

But you'll find that the amount of opportunity to use wirewrap is still small per project, and it should be "just one technique" for making connections, not the main technique above all else. Soldering is probably the closest you have to a "bread and butter" skill that's used everywhere.

Re:RadioShack’s new owner plots old comeback strategy by nodesocket on Sunday September 03, 2023 @05:57PM (#37374993)
I honestly don't know how Michaels is still in business. I do tend to think it's not necessary location that is going to make it for Radio Shack, but their products, and target market. They should focus on makers, Raspberry Pi, Arduino, Drones, make that their core business. Pricing needs to be competitive (vs online), stock should be plentiful, and knowledgeable employees (maybe like a Geek Squad equivalent "The Shack").
Re:RadioShack’s new owner plots old comeback strategy by lancesells on Sunday September 03, 2023 @06:07PM (#37375059)
The thing with Michaels is there are a lot of products that are nicer to experience in offline instead of online. For electronic components I'm not sure that's the case. I know very little about electronics but I would much rather go to adafruit.com and look at tutorials, specs, etc. and then order. I personally don't need any sort of tactile feel or quality control on breadboard compared to if I'm buying yarn to knit something.
Re:RadioShack’s new owner plots old comeback strategy by bbarnett on Sunday September 03, 2023 @06:38PM (#37375282)
The thing with Michaels is there are a lot of products that are nicer to experience in offline instead of online.

I agree, and even wonder what's up with bed bath and beyond's implosion. Many people, mostly but not only! women, tend to really really care what pillows look and feel like.

I think the only reason Amazon works here, is the crazy free return shipping.

But still, how is that the same?? I don't care about pillows, but I know if I did, I'd want to choose! To touch! To see how fluffy, how they look..

Hrm. Maybe I am harbouring an unknown pillow fetish.

Anyway, I don't get it either. If Michael's can't survive, can anything?

Re:RadioShack’s new owner plots old comeback strategy by bombcar on Sunday September 03, 2023 @06:43PM (#37375330)
Bloodbath and beyond was just insanely overpriced. Kohls is surviving because they have billions of coupons, but they also are encroaching on things like BB&B sold. They were finally killed in my opinion by the wedding registry options at other stores getting better.

Michael’s survives by having way more art supplies than other places and people who do art wanting it NOW and not later.

Re:RadioShack’s new owner plots old comeback strategy by troupe on Sunday September 03, 2023 @06:16PM (#37375125)
Frames, both custom and premade, tend to be harder to order online because of shipping and because you often want to actually see it...or someone has to made it for you. Many of the craft or home decor items are similar. Michael's markup on those types of things is probably pretty high, so even the stuff sold on sale after the season is probably making good profit.
Re:RadioShack’s new owner plots old comeback strategy by bsder on Sunday September 03, 2023 @06:08PM (#37375067)
> Everyone buys these things online or at Walmart.

Most people need in-person, tech customer support--especially in small towns. Radio Shack could find a nice niche by being that.

The problem is that while it could be profitable, it won't be a "growth industry". And that seems to be a gigantic problem given the MBA management mindset in the US.

Re:RadioShack’s new owner plots old comeback strategy by notatoad on Sunday September 03, 2023 @06:35PM (#37375260)
"people will pay more to shop in person because they want the in-person support that our staff provide" is written on the gravestone of every dead retail company.
Re:RadioShack’s new owner plots old comeback strategy by bsder on Sunday September 03, 2023 @07:32PM (#37375662)
Only because they try to scale.

Support doesn't scale. It's weakly profitable. It's specific to an area. It's slow. It requires workers with a bit of clue.

Support is everything that modern business culture loathes.

Re:RadioShack’s new owner plots old comeback strategy by notatoad on Sunday September 03, 2023 @10:07PM (#37376475)
Support scales fine. there's plenty of huge companies built around charging for support, all the way up to consulting companies like IBM and SAP.

support doesn't scale, or work at all as a business, if you aren't charging for it. if you're providing free support as a loss leader to get people to buy your stuff, people will take the free support and leave. it's nothing to do with scale.