Drawback: any excess power that one does not use oneself is fed into the grid without compensation.
It's a step in the right direction, I guess?
They are approved at up to 600 Watts in Germany, and that will probably get increased to 800 Watts soon. You can just plug the inverter output into an outlet. This is called "balcony power plants" here, and lots of municipalties are subsidizing it currently. You can't get net metering, but you can offset some of your load with minimal cost and paperwork.
And 600w is probably below the average usage anyway.
The old ones (Ferraris meter?) just ran backwards, which is attractive of course. Our new meter has a P1 port which can integrate into eg. Home Assistant
Maybe screw terminals would be ideal so you can cut your wall wart cable and wire it up. Most devices will have a bridge diode inside (total waste of electricity, but not going there right now).
I guess a cigarette lighter port could make sense but now we might be asking too much on the BoM.
Those little barrel jacks are fine for what they are, but I can't imagine powering a toaster oven with one. Cigarette lighter ports might fit the bill, at least mechanically. I haven't seen one of those in many years and forgot about them.
A kilowatt at 12V is going to be 85 amps.
Not sure what’s approved for DC use in general. Standards bodies will probably disagree with using something typically used for AC with DC because of the risk of plugging the wrong thing into it.
https://www.neutrik.com/en/products/power/powercon-20-a
https://www.te.com/usa-en/products/connectors/automotive-con...
Would you mind explaining this sentence? I know very little about these things but I'd like to, are you saying that rooftop solar switches itself off if there's no grid power? And if so, why?
But this is so that they don't supply power when eg an electrician flips a breaker to safely do work. Then better not have the system still energized by solar...
I guess the risk with smaller, plug in systems is that they're simpler without such precautions? And you would have 2 live prongs sticking out, which would be bad of course
The cheapest ones just cut power when the sine is lost and then make their own, and cut power when they see it return and then sync.
Not practical in the USA with split-phase 120/240 (or 120/208 open wye) as you need to connect to both hot legs of the system to feed everything. In 230V countries they mostly have 2 wire service with (I hear some have three phase 230/400) so its easier to evenly back-feed a 2 wire system.
> I always question why we choose between 0kW solar installs OR multi-kW residential installs ...
Agreed. I have a small home server setup that draws 40W idle and I toyed with the idea of replacing the UPS with a small 1-2kW battery inverter plugged into the wall.
My concern with rogue solar installs is how does that interact with the utility company? Their smart meters will see reverse flow of current and if I do not have an "official" solar install, will they force me to adopt one or disconnect my system as it is not approved? So I would only build a system which draws from the utility as needed (cloudy days) and dumps excess power - never back feed.
No idea if this would work in practice, but you might be able to backfeed your battery with a regulated 11.9V onto the 12V lines and backfeed at 4.9V on the 5V lines, so when the power supply shuts off and puts 0V on the 5V and 12V lines, the battery will start back feeding, but when the grids power supply puts out 5V and 12V, no current will move.
(Will need blocking diodes to avoid back-feeding the battery that’s kept topped off by its mains charger)
Saves you some DC->AC->DC conversions. You might need a 3.3V leg as well. And maybe negative voltages if those are used for anything anymore?
Just choose which half of your house you want to power :)
But presumably these shutoff when grid mains is lost.
What does this do?
You might have noticed how much time it takes to freeze something - that's because lots of energy need to be extracted from liquid water to turn it to ice. And that without even changing temperature - it all happens at 0°C. With other materials, you can have a similiar effect at other temperatures. This can be used to create a system that keeps a certain temperature even if energy flows into or out of it (until the phase transition is complete).
Read more here: https://en.wikipedia.org/wiki/Phase-change_material
Using this you can avoid hearing water during high demand times.
Melting water ice into liquid water at 0°C takes approximately as much energy as heating the same amount of water from 0°C (assuming that it is already/still liquid) to 80°C.
With a material that has a transition temperature of e.g. 21°C, a room could be kept at a very pleasant temperature even when energy is flowing into or out of it.
In California, touching a breaker box is at least $10,000, so to amortize the cost of the paperwork, you need to put in a multi kw system. On top of that, you need to anchor it to the ground somehow, so that it doesn’t fly around in 50-100mph winds (which will happen about once during the lifetime of the panels).
Portable systems exist, of course. You could get one of those.
Also, a multi-kw system isn’t physically that big.
Like, I understand we have the technology to monitor if grid disappears and self-disable, and a lot of hard-wired rooftop solar does that, but unsure if any soft-wired units have been approved.
My fridge is inverter drive and likely operates off DC at its core. Hopefully Samsung or somebody in the future will put a 48VDC port and anyone can plug in a solar panel and it will soak up whatever juice comes off that and use grid for the rest. That avoids batteries (because the fridge does thermal banking), electricians (because 48V is usually excluded), and inverter drive fridges tend to be continuous drive, so running slower when the sun is marginal or full-speed when full works nicely.
And it puts some juice into the thing I really depend on if the power goes out (even if only during the day).
And consumers can cheaply add some phase change materials for a boost in thermal banking (like really salty water bottles).
Put a couple USB charging ports and 12V ports on it too that switch between solar & grid. My router and modem sit on the top of my fridge and use 12V
And then we do away with the increasingly unnecessary DC->AC->DC conversion cycles.
Seems like the lowest hanging fruit to inexpensive mass (mild) solarization.
I always question why we choose between 0kW solar installs OR multi-kW residential installs when we could do massive 250w solar rollouts at low cost with very high efficiency.