And now I realize that sounds like astroturfing.
Generic cartridges are just find and you refill them easily.
HP probably would have been my only other choice if/when I have to replace my superb (and crazy cheap) Brother B&W laser but after reading this post I will never go near HP printers again.
Edit: just read about Brother’s nasty firmware update elsewhere in the comments here. Sigh. I guess I’ll just have to stop buying printers altogether.
There was no support on the new OS at all. With a lot of luck one could print b&w, but color never worked again.
I never experienced that using HP or Xerox.
IMHO, those are mostly personal experiences that lead to preferred manufacturers. For each story where one tells you he never had any issue you'll find one that for sure had issues.
the cost of the old Brother and then a new Brother at that point would have been cheaper than the cost of either the HP or the Xerox
and if you were using linux (and almost as often Windows too), the old drivers would have still worked.
Was quite frustrating but nowhere near as bad of some of the HP stories like this that I read on HN.
To enable Continue Mode, perform the following steps:
1. Press Menu.
2. Press ▲ or ▼ to select General Setup. Press OK.
3. Press ▲ or ▼ to select Replace Toner. Press OK.
4. Press ▲ or ▼ to select Continue. Press OK.
5. Press Stop/Exit.
When a printer signaled that the toner should have run out, I checked the cartridge. It apparently had enough toner left, so I entered a special code and reset the counter for the cartridge.
I can only recommend their laser lineup.
It's sad that manufacturers resort to these schenaningans at all.
There might have been an update to add iOS printing to it via some software bridge, but I never checked. There are multiple tutorials online about setting up a Raspberry Pi (even a zero w) as an AirPrint server and interfacing with the printer via CUPS. This allows using a lot older printer models as well that don't have built-in wifi.
https://www.tomshardware.com/how-to/raspberry-pi-print-serve...
So it seems Brother is not immune from giving into the temptation of turning into a terrible printer company. Hopefully they don't continue down that path.
(I can't remember which model I have and am away on travel, but I can update assuming anyone cares...)
Tangentially, can we talk about old printers being too scary to connect to the network? No firmware upgrades ever. I've been thinking of setting up a RPi or something as a bastion host and print&scan server, preventing direct traffic.
It works great. The only negative comment is that it starts to cry for a new cartridge some 6 months early, but I just go on printing and there are no problems (they even have a setting with what to do when "ink is low": stop and cry or go on)
The problem with laser printers is that they have a much higher upfront cost, especially if you actually need color. Sure, they are probably worth it in the long run, but that bigger price tag stops a lot of people from getting one.
I got burnt out after dealing with an old Epson inkjet back in the day. Never want to go back to that.
They do. I have this model and aftermarket toners work effortlessly. I'll never buy HP or Lexmark. They're the worst.
I can't speak to current practices, as my current Brother printer is now 7 years old and is still on its second toner cartridge. It's a B&W laser with wifi, a duplexer, and whatever discovery stuff that iDevices need to find and print to it driverless.
It replaced a very similar Brother printer that had gotten a solid 10 years of service, and which I chose to replace rather than repair when the fuser died mostly because I wanted the iDevice affordances.
Both of those printers also worked smoothly from Linux desktops, too, thanks to pretty good PostScript emulation.
Maybe they've gone to crap now, but I'm optimistic that if I needed another B&W laser, something like their current HL-2350DW or HL-2370DW would provide a similarly inexpensive, no-bullshit experience now.
The thing that worked for me was giving up on color printing. The supplies for that are eye-wateringly expensive IMO, and I seldom really need it. Last time I had a color printer at home, it was an Epson ink jet of some description, and my color prints were so infrequent that sometimes the cartridge would dry out after a few dozen pages. And worst of all, it'd refuse to do B&W prints if one of the colors was dry. I decided I'd just go to Kinko's if I needed a color document, or to one of several drug stores that lets you print photos if I needed photos. Black and White lasers are stable. Taking apart my Brother, it is extremely similar to the Canon engines from the 1980s. Which were themselves extremely similar to photocopiers that have been in production since quite a bit earlier than that.
B&W laser printing is such a well-solved problem, if you can stand to go with that you can save yourself a ton of aggravation and quite a bit of money.