News for hackers. Stuff that matters.
Re:Teardown of a $1.25 LED Lightbulb by spookthesunset on Wednesday February 19, 2020 @10:51AM (#22366532)
Some of these cheap LED bulbs have horrible flicker. For a fun time, record a slow motion video of a cheap bulb on your phone and play it back. Like half the damn video is black (pretty sure it is because they literally chop out half the AC sine wave with a diode). LED Christmas lights are also really bad.

Then compare it to something like a Phillips hue bulb. The difference between the two is pretty big.

On a side note I sometimes wonder if other animals have a quicker “refresh rate” on their eyes and see nothing but very visible flicker on these bad LED bulbs. I also wonder if some animals could see the raster scan in action on old CRTs...

Re:Teardown of a $1.25 LED Lightbulb by derefr on Wednesday February 19, 2020 @11:01AM (#22366655)
It’s not like these bulbs are flickering in a way you can perceive just by slowing it down by 2/3/4x. They’re flickering at 10000+ Hz. The reason cameras perceive the flicker is that they take discrete samples, with an (electronic or optical) shutter in between. This creates a beat frequency with things that also flicker, in effect “tuning into” a HF flicker and “lowering it” into the visible range, the same way a superheterodyne radio tunes into a HF carrier wave and brings it down into the audible range.
Re:Teardown of a $1.25 LED Lightbulb by pwg on Wednesday February 19, 2020 @11:32AM (#22367052)
The 10khz+ flicker only comes about if the bulbs have a proper switching power supply (and if that switching power supply itself runs at 10khz+).

But for the 'real cheap' bulbs, they likely (due to being "real cheap") have either a half wave or full wave rectifier (i.e., no switching PSU) which results in the LED's having a flicker at power line frequency (either 50hz, 60hz, 100hz, or 120hz depending upon which combination of line frequency and full/half wave rectifier is present).

Re:Teardown of a $1.25 LED Lightbulb by nicolaslem on Wednesday February 19, 2020 @01:37PM (#22368539)
Now that incandescent bulbs are almost gone, I wonder if it will become common to have wires carrying DC in the ceiling instead of every bulb having to implement the AC to DC conversion as cheaply as possible.
Re:Teardown of a $1.25 LED Lightbulb by 205guy on Wednesday February 19, 2020 @04:58PM (#22370529)
With renewable energy and local batteries, it would make sense to have DC wiring. It used to only be that off-grid systems had batteries (usually lead-acid), and they always just use an inverter. But now with battery packs such as the Tesla Powerwall, even grid-connected houses have DC storage.

Unfortunately, Powerwalls and other similar products are made with built-in inverters and connect only to AC, there is no DC tap. And there aren't any standards around DC wiring and small appliances, so it isn't likely to get traction.

I'm mentioned before (https://news.ycombinator.com/item?id=21109247) that I've seen a DC installation at a friend's house, he used 12V cable lights and DC bulbs, so it seems to work.

Re:Teardown of a $1.25 LED Lightbulb by zaroth on Wednesday February 19, 2020 @03:34PM (#22369767)
I have DC powered under-cabinet lights which are definitely flickering at some fairly high rate.

Imperceptible if you are just looking at it, but in a dark room if you move something quickly in front of it you can see the strobe effect.

Re:Teardown of a $1.25 LED Lightbulb by 205guy on Wednesday February 19, 2020 @04:44PM (#22370404)
But where is the DC coming from? If it is a cheap power source (a rectifier plugged or wired into AC), the DC into the lights could be intermittent, and so cause flicker. For true continuous DC, you need a good rectifier or get the current directly from batteries.
Re:Teardown of a $1.25 LED Lightbulb by andruby on Wednesday February 19, 2020 @01:57PM (#22368770)
Then we can also use this for our video camera’s and wireless access points. Maybe we can add network to those cables. Let’s call it “power over ethernet” ;)
Re:Teardown of a $1.25 LED Lightbulb by elFarto on Wednesday February 19, 2020 @02:13PM (#22368931)
Ubiquiti has got you covered:

https://unifi-led.ui.com/

Re:Teardown of a $1.25 LED Lightbulb by kps on Wednesday February 19, 2020 @02:30PM (#22369110)
The real cheap filament style bulbs are a rectifier, and nothing but.
Re:Teardown of a $1.25 LED Lightbulb by syphilis2 on Wednesday February 19, 2020 @11:42AM (#22367174)
I have 960 fps video of some LED bulbs in my house. It's very apparent that some bulbs do not flicker (perceptibly), some flicker at 120Hz, and some flicker at 60Hz. At night I can sweep my eyes across the bulbs and see the dashed lines resulting from them turning off and on.
Re:Teardown of a $1.25 LED Lightbulb by sjg007 on Wednesday February 19, 2020 @08:08PM (#22371870)
Yeah mine do that, you can see it in slo-mo video mode.
Re:Teardown of a $1.25 LED Lightbulb by smoyer on Wednesday February 19, 2020 @11:08AM (#22366747)
Yep ... it's the digital (meaning on-off) version of the slow moving line you see if you point your camera at a TV (or computer) screen - the speed that it happens at is the sum and the difference of the two frequencies (and perhaps at the sum/differences of their harmonics).

In the CATV industry, we used to send 110 analog channels across roughly 800MHz of spectrum (54MHz to 860MHz). Other than background and ingress noise, a major source of noise (effectively) was distortion - non-linearities in the amplifiers that kept the signal at a reasonable level. Composite Second Order (CSO) and Composite Triple Beat (CTB) distortions were two values that equipment transporting these signals would generally call out - they are analogous to the summing and differencing of two signals and three signals (respectively) as described above for the lightbulb, but imagine doing that with 110 different frequencies simultaneously.

Re:Teardown of a $1.25 LED Lightbulb by Robotbeat on Wednesday February 19, 2020 @11:06AM (#22366723)
Filament LED bulbs usually flicker at 120Hz (with high duty cycle) and Christmas LEDs at 60Hz (with a short duty cycle). Other LEDs are, indeed, high frequency like you describe and are perceptually effectively constant.
Re:Teardown of a $1.25 LED Lightbulb by vidanay on Wednesday February 19, 2020 @11:32AM (#22367051)
The filament in a filament bulb doesn't fully cool down when the voltage crosses to zero, so that smooths them out a lot.

Sorry...I just noticed you are talking about filament LED and not old fashioned analog filament bulbs.

Re:Teardown of a $1.25 LED Lightbulb by spookthesunset on Wednesday February 19, 2020 @11:15AM (#22366841)
I guess you are right about the beat frequency bit, but I still assert that the cheap LED's are cycling on and off 60 times a second (or 30.... math is too hard early in the morning). That is a bit low for my taste.
Re:Teardown of a $1.25 LED Lightbulb by seiferteric on Wednesday February 19, 2020 @12:01PM (#22367420)
Take a battery, photo-resistor and a capacitor and hook up to headphones in series and you will be able to hear your bulbs flickering.
Re:Teardown of a $1.25 LED Lightbulb by mrb on Wednesday February 19, 2020 @04:56PM (#22370501)
No, as reported by other posters, most bulbs that flicker do it at 120 Hz or 60 Hz. This is easily confirmed by eyesight alone because 60 or 120 Hz can be perceived when an object illuminated by the bulb (eg. your hand) moves quickly in front of a dark background.
Re:Teardown of a $1.25 LED Lightbulb by ubercow13 on Wednesday February 19, 2020 @05:34PM (#22370838)
Some bad LED bulbs flicker so slowly you don't even need to video it, you can just tell when you walk into the room
Re:Teardown of a $1.25 LED Lightbulb by macNchz on Wednesday February 19, 2020 @11:31AM (#22367040)
Yes I find these cheap LED bulbs nearly intolerable-the flicker is especially noticeable because they transition so quickly from fully illuminated to fully dark. I’ve always perceived a slight flicker from fluorescent lights but because the phosphors smooth it into more of a fade in and out it’s much less distracting. I definitely think people perceive these things differently...I recently stayed in a hotel room lit entirely by these cheap LED bulbs and it was the first thing I noticed from walking in. It really bothered me that every light fixture strobed as I moved my eyes, but my girlfriend barely noticed it and only after I pointed it out.

The OLED displays in current smartphones also exhibit a visible strobe effect at lower brightness settings. I figured I’d get used to it but ended up returning my iPhone 11 pro after a week because it was driving me nuts. I’ve met a few people who perceive it as well but most seemed to have no idea what I was talking about.

Re:Teardown of a $1.25 LED Lightbulb by Robotbeat on Wednesday February 19, 2020 @11:04AM (#22366701)
The filament bulbs are almost all like this. Not too bad if they're using an H-bridge (120Hz with high-ish duty cycle), but Christmas LEDs I think might use no separate diodes at all, just relying on their own diode-ness. That means they're 60Hz with a less-than-50% duty cycle.

Filament LED bulbs (the ones that look almost exactly like clear incandescent bulbs with a visible filament when turned on) do this because they have to fit their electronics in the tiny metal base. Room enough for some diodes (and maybe a capacitor), but usually not a full set of high frequency switching electronics like in most other LED bulbs (although I've seen some filament bulb tear downs that might show more advanced electronics). But again, doesn't bother me due to their high duty cycle and relatively okay refresh rate.

(At least, this is all my impression. Please correct me.)

Re:Teardown of a $1.25 LED Lightbulb by all_usernames on Wednesday February 19, 2020 @10:58AM (#22366622)
Dogs apparently have a visual sample rate of around 75Hz, meaning they wouldn't see much in an old analog TV, but newer HDTVs might look realistic to them.

https://thebark.com/content/heres-what-dogs-see-when-they-wa...

Re:Teardown of a $1.25 LED Lightbulb by joshspankit on Wednesday February 19, 2020 @11:23AM (#22366948)
I’m very suspicious of this 75Hz number. We’ve also heard that 60Hz is the limit of human perception but I think we all know now that we actually perceive higher than that (seeing flicker at 120Hz, blind A/B testing of 240Hz monitors, even perceptual flickering for some people in 1000Hz PWM LEDs).

Even if that 75Hz number were derived from deep understanding and measurement of the entire visual pathway, there are variations in perception for people, there most likely are for dogs as well.

Re:Teardown of a $1.25 LED Lightbulb by waiquoo on Wednesday February 19, 2020 @12:00PM (#22367414)
60Hz is the 'flicker fusion rate', meaning if you were changing the frequency of a flashing, stationary LED, ~60Hz would be the frequency where perception transitions from visibly flickering to apparently continuous. It's a lower threshold for refresh rate in the human eye. When you have complex refreshing images (a 2d computer screen rather than a point-like LED, diverse motion, depth, etc), you are likely to notice flickering (or tearing, jittering, non-smooth motion) if the refresh rate is near this minimum.
Re:Teardown of a $1.25 LED Lightbulb by barrkel on Wednesday February 19, 2020 @04:37PM (#22370361)
People routinely watch movies which refresh at 24Hz and motion is apparently continuous.

Perceiving flicker has a higher threshold. I can perceive 60Hz flicker in my peripheral vision easily enough.

Other sources online (you can find lots of them but I didn't see an obvious authoritative article) suggest that 16Hz is the flicker fusion rate for motion in humans.

Flicker fusion for continuous brightness (CFF) is somewhere around 30Hz per https://www.nature.com/articles/s41598-017-15034-z and it rises with brightness - this paper is about testing how it changes in different circumstances.

Re:Teardown of a $1.25 LED Lightbulb by svachalek on Wednesday February 19, 2020 @04:48PM (#22370433)
Unless the camera moves fast and then it looks like a slideshow. Whenever they pan across a landscape it makes me grit my teeth.
Re:Teardown of a $1.25 LED Lightbulb by mdpye on Wednesday February 19, 2020 @05:01PM (#22370563)
This is often exacerbated horribly by the fact that the 50 or 60 FPS output doesn't divide well by the 24 FPS source material. It was smoother in the cinema, when it was projected at 24 FPS...
Re:Teardown of a $1.25 LED Lightbulb by joshspankit on Friday February 21, 2020 @09:09PM (#22388919)
Fair point, but I (and many others) see stutter in theatre as well.

Most of the reason you don’t is because filmmakers know very well what their “maximum pan speed” is and they stay as far away from it as possible.

Re:Teardown of a $1.25 LED Lightbulb by ColanR on Wednesday February 19, 2020 @04:39PM (#22370371)
And don't forget about harmonics. Seems like flicker at higher refresh rates would happen whenever the mental and external rates synchronize.
Re:Teardown of a $1.25 LED Lightbulb by Someone on Wednesday February 19, 2020 @12:10PM (#22367532)
The limit depends on the size of the source, contrast, location on the eye of the source (rods are much ‘faster’ than cones, so we see flicker better out of the corners of our eyes), and probably a few other factors.

1000Hz I find hard to fathom, though. Would want to see what these signals look like.

Re:Teardown of a $1.25 LED Lightbulb by Someone on Wednesday February 19, 2020 @12:05PM (#22367474)
https://en.wikipedia.org/wiki/Flicker_fusion_threshold.

Classical 50/60Hz lighting looks like a stroboscope to chickens. There is a whole field of research on the effect of light regimes, light color and flicker on poultry farming efficiency. I couldn’t find a scientific link, but see https://agrilight.nl/lichtadvies/pluimvee/?lang=en&-en

Re:Teardown of a $1.25 LED Lightbulb by berdon on Wednesday February 19, 2020 @11:11AM (#22366782)
Our two dogs watch our 4k TV often. And bark at various things, actors, subjects they don't like.
Re:Teardown of a $1.25 LED Lightbulb by Topgamer7 on Wednesday February 19, 2020 @11:48AM (#22367249)
Had a dog that would press her nose right up to an ipad screen and move her face around to follow the squirrel, bird, or dog that interested her. She would get very excited about it. She also watched TV. At one point sitting on hind legs trying to elevate off the bed to be inline with the center of the image.
Re:Teardown of a $1.25 LED Lightbulb by bradstewart on Wednesday February 19, 2020 @04:16PM (#22370151)
Only one of my dogs appears to recognize things in the TV. She'll bark at something on screen, and my other dog will run to a window or door trying to figure what he missed. Always wondered why...
Re:Teardown of a $1.25 LED Lightbulb by brutt on Wednesday February 19, 2020 @11:27AM (#22366995)
Re:Teardown of a $1.25 LED Lightbulb by Junk_Collector on Wednesday February 19, 2020 @03:02PM (#22369455)
This is actually a pretty big deal if you work with high speed or rotating machines. Using an high flicker LED bulb over your lathe (for instance) can cause it to appear static when it is in fact running due to visual aliasing. There are lines of flicker free LED bulbs for industrial spaces for this reason.
Re:Teardown of a $1.25 LED Lightbulb by 0xff00ffee on Wednesday February 19, 2020 @01:37PM (#22368541)
Funny you mention animals. I often wonder if home environments have become screaming dens of high-frequency noise for dogs and cats. I know that flourescents tend to osciallate around 40kHz, and I definitely have an LED bulb that whines for some reason. Not to mention cheap laptop power supplies that also whine over time.

Are all these cheap SMPS driving our pets insane? (or just annoying them? or neither?)

I wonder if I could rent some super-high-quality mic from a local sound reinforcement studio and look at a 20-60kHz FFT ... or do fancy mics not really go beyond human hearing?

Re:Teardown of a $1.25 LED Lightbulb by dspig on Wednesday February 19, 2020 @04:11PM (#22370099)
High quality recording mics and even mics designed for acoustic measurements usually (and deliberately) only go up to 20-40 kHz though roll off more gently than human hearing. Usually there is a mechanical resonance that's tuned to get a flat frequency response up to a point rather than a wider but rolling off response. A few specialist mics get up to 100 kHz, or some sort of laser vibration measurement...
Re:Teardown of a $1.25 LED Lightbulb by tyingq on Wednesday February 19, 2020 @11:03AM (#22366695)
I don't know about the bulbs, but commercial LED drivers from companies like Meanwell typically let you select a range between 100Hz and 1000Hz for the PWM frequency.
Re:Teardown of a $1.25 LED Lightbulb by LinuxBender on Wednesday February 19, 2020 @12:17PM (#22367605)
I can tell when I am around these bulbs. It is the same with fluorescent lights for me. They make me (more) grumpy. The more expensive LED lights have full wave bridge rectifiers and capacitors with no flicker. I've considered just building my own for my next home.
Re:Teardown of a $1.25 LED Lightbulb by tomatocracy on Wednesday February 19, 2020 @01:36PM (#22368515)
Some LED lights/bulbs also incorporate phosphorescent materials and use UV LEDs to stimulate the phosphor which helps too. This is also one of the ways better colour reproduction can be achieved. This comes at a slight efficiency cost though, I think.
Re:Teardown of a $1.25 LED Lightbulb by extrapickles on Wednesday February 19, 2020 @03:22PM (#22369649)
Most LED lights use the UV+phosphor technique as its cheaper than doing RGB (If the LED is yellowish when switched off, its using this technique).

The best flicker-free lights are ones that have low ripple constant current power supplies (somewhat expensive). LED lamps intended for use around rotating machinery used to all be this way until someone figured out that if the PWM frequency was wildly unstable it would prevent the problems with strobe lights around spinning things at a fraction of the cost.

Re:Teardown of a $1.25 LED Lightbulb by Tepix on Wednesday February 19, 2020 @11:26AM (#22366985)
Are there any statistics how many people perceive this flicker? I see them complain in online forums but I'm not sure if it's just a very loud small minority.

What does it take to make them not flicker? I.e. how much of a cost increase is required?

Re:Teardown of a $1.25 LED Lightbulb by uxp on Wednesday February 19, 2020 @12:55PM (#22368064)
Based upon this article were the retail costs of a cheap flickering LED bulb is approaching the single dollar mark, the cost increase to use a proper AC/DC converter could be orders of magnitude more expensive (at a rough minimum).

Honestly it's starting to feel like a most cost effective long term solution is to build homes with a master AD/DC converter (or several depending on sq/ft) and simply wire 12v outlets and light fixtures. The energy savings of swapping all incandescents or compact florescence bulbs with cheap LEDs with cheaper power converters is starting to scare me knowing just how shoddy and fire prone some of these power converters can be.

Re:Teardown of a $1.25 LED Lightbulb by BlueTemplar on Wednesday February 19, 2020 @01:07PM (#22368194)
I expect USB-C outlets to become common in new homes...
Re:Teardown of a $1.25 LED Lightbulb by ksec on Wednesday February 19, 2020 @01:20PM (#22368348)
I have been thinking about this for years! I think we need a new marketing term along with a independent organisation to push for a new LED Standards.

Let say it is called CLED,

And it requires the following features / spec before it could be called CLED. From PWM, Colour Correctness, Energy Efficiency, heat etc. The different between a low price light bulb and higher priced is relatively minimal , the difference in LEDs is massive. To be point they should not even be allowed into the market in the first place.

Re:Teardown of a $1.25 LED Lightbulb by tomatocracy on Wednesday February 19, 2020 @01:32PM (#22368482)
Brand (and in some cases sub brand) is a reasonably good proxy for this already though. Philips bulbs for example tend to be very good.
Re:Teardown of a $1.25 LED Lightbulb by tasogare on Wednesday February 19, 2020 @11:00AM (#22366639)
Philips bulbs are also at least twenty times more expensive, which is a lot of money for a light bulb.
Re:Teardown of a $1.25 LED Lightbulb by hocuspocus on Wednesday February 19, 2020 @03:31PM (#22369736)
You don't need to buy Hue... Their 8W 800lm bulbs are €4 a piece in Europe, and a lot less in bulk. So 4x more expensive at worst.

Philips' discount brand (Attralux) is even cheaper, I recently bought more of these 8W 800lm for less than €1 a piece. For now I cannot tell the difference.

Re:Teardown of a $1.25 LED Lightbulb by codereflection on Wednesday February 19, 2020 @01:20PM (#22368353)
True, however they are worth the price. I used various brands of LED bulbs for a long time (such as Cree), basically whatever Home Depot was selling. The failure rate was extremely high. In 2017 I switched to Philips LED bulbs, and just last night the first one failed. Overall they are worth the extra up front cost, they'll save you money in the long run.
Re:Teardown of a $1.25 LED Lightbulb by spdustin on Wednesday February 19, 2020 @03:20PM (#22369622)
I have three weighty Philips bulbs mentioned in the teardown as carriage lights on the exterior of my house. They've been on 24/7 for maybe seven years now.
Re:Teardown of a $1.25 LED Lightbulb by Scoundreller on Wednesday February 19, 2020 @06:13PM (#22371145)
Don’t underestimate the thermodynamics of a slight breeze vs. Passive dissipation alone.
Re:Teardown of a $1.25 LED Lightbulb by scarejunba on Wednesday February 19, 2020 @12:44PM (#22367910)
That is just the stroboscopic effect. It’s an artifact of your measuring tool. I’m not saying that your lights aren’t flickering but your tool is introducing a lot to this system and so you can’t use it as evidence.
Re:Teardown of a $1.25 LED Lightbulb by brewtide on Saturday February 22, 2020 @12:51PM (#22392261)
Can you recommend the optimal bulb between price and "flicker free smartphone slow mo" ?

Just white. We run whatever cheap bulbs in my house at the moment, but also tend to do to a lot of "slow mo" videos and it kills me every time.

I'd prefer NOT to spend $15+ a bulb for crazy high end but would be more fine with say, $5+ a bulb

Re:Teardown of a $1.25 LED Lightbulb by gumby on Wednesday February 19, 2020 @11:46AM (#22367222)
> On a side note I sometimes wonder if other animals have a quicker “refresh rate” on their eyes.

Indeed, to the housefly, an incandescent-bulb-lit house slowly pulses from light to dark, so probably too with cheap line voltage choppers.

Re:Teardown of a $1.25 LED Lightbulb by SamBam on Wednesday February 19, 2020 @11:49AM (#22367260)
> an incandescent-bulb-lit house slowly pulses from light to dark

This sounds amazing to me, but also confusing. My understanding is that an incandescent bulb works entirely by heating up the filament. There should be no way that the filament is cooling down and heating up in anywhere close to the rate that it would require to get some kind of wagon-wheel effect, which is what it sounds like you're describing.

Re:Teardown of a $1.25 LED Lightbulb by pwg on Wednesday February 19, 2020 @01:00PM (#22368123)
Ignoring 'complex power' concerns, the AC voltage driving a tungsten filament bulb is a sine wave at line frequency (60hz for the US). Because it is a sine wave, and because the tungsten filament is a resistor, the current through that resistor rises and falls in sync. with the AC sine wave. The current will be zero at the zero volt crossing point of the wave, and maximum at the peaks of the sinewave.

The varying current through the tungsten will result in a varying power consumption (varying at a 60hz rate). The varying power consumption will result in a small amount of varying temperature on the filament.

Now, the filament does not cool down instantly, so the result is its temperature will vary by a few degrees, but likely not enough to ever be perceptible to human eyes. But with a sensitive enough (and fast reacting enough) temperature probe, one could likely measure the temperature rise/fall of the filament that is synchronized with the line frequency.

Re:Teardown of a $1.25 LED Lightbulb by SamBam on Wednesday February 19, 2020 @03:33PM (#22369758)
Right, the wave filter effect caused by the thermal mass of the filament was my point.

I'm not sure you've shown that this would be visible to a housefly as a "slow pulse from light to dark," as the post I was replying to claimed. First of all, you said the power consumption will vary at a 60hz rate, but it seems to me it will vary at a 120hz rate, since the current will be at its max magnitude twice per cycle (as you say in the first paragraph). But more to the point, I don't know whether the temperature/lumens will decrease enough in 1/120th of a second to be visible to houseflies or anything else.

Trying to research the answer, I found this physics lab worksheet [1] from Pasco (the makers of sensors), for a high school lab measuring the output frequency of incandescent bulbs vs fluorescent bulbs, but without doing the lab I don't know the results.

1. http://phylab.yonsei.ac.kr/exp_ref/pasco/P54_BULB.pdf

Re:Teardown of a $1.25 LED Lightbulb by Dylan16807 on Wednesday February 19, 2020 @11:37PM (#22372706)
https://www.quora.com/Would-a-120-volt-incandescent-bulb-ope...

The numbers here show a >25% difference for an example bulb.

Also, even ignoring how the cooling starts off at its fastest, with radiation scaled to the fourth power of temperature... incandescent lights switch off in about a tenth of a second. Even if that was completely linear, it would be very visible. Even a 1% flicker would be visible.

Re:Teardown of a $1.25 LED Lightbulb by SamBam on Thursday February 20, 2020 @10:53AM (#22375906)
Huh, good find. I wish the poster had some sources, especially for that initial temperature graph, but there's no reason to doubt it. Thanks for the research.
Re:Teardown of a $1.25 LED Lightbulb by whatshisface on Wednesday February 19, 2020 @11:49AM (#22367267)
Incandescent bulbs store thermal energy in the fillaments, lowpassing the signal in the same way as a capacitor would on an LED bulb. A 60Hz flicker would be perceptible and if incandescents had that problem nobody would use them.
Re:Teardown of a $1.25 LED Lightbulb by Dylan16807 on Wednesday February 19, 2020 @11:18PM (#22372637)
They pulse at 120Hz, not 60.

https://www.youtube.com/watch?v=eUprJS9sXYU

https://www.youtube.com/watch?v=jXx5eEzMmYo

It's not an extreme brightness change, but it's possible to do a lot better.

Re:Teardown of a $1.25 LED Lightbulb by zadler on Wednesday February 19, 2020 @11:50AM (#22367278)
If that were the case I wonder if there is a frequency which the fly’s vision has a hard time adapting to.
Re:Teardown of a $1.25 LED Lightbulb by throwanem on Wednesday February 19, 2020 @12:42PM (#22367890)
Likely. As with dragonflies, there is a minimum speed below which flies don't perceive motion. In both cases, if you move very (very) slowly, you can approach almost to physical contact without provoking any reaction.

Anecdotally from my experience as a macro photographer, the threshold for flies is lower than for dragonflies; flies often startle in response to movements almost too tiny to perceive having made, while dragonflies are relatively easy, usually requiring only a few minutes to approach from a distance of a meter or so to the ~12cm minimum focus distance of my best macro lens. (It's hard to know; the passage of time isn't of much interest in the focused flow state that's required for this sort of activity.) It helps that disturbed dragonflies tend much more often to return to the same perch, but with some practice it's possible to make the entire approach without disturbing them at all. The only really tricky part about it is that, when you're moving slowly enough, they also tend to land on you, which can be somewhat distracting if you're ticklish.

In any case, the existence of a minimum rate of change for perception of motion suggests that flickering light below a certain frequency might well be perceived as strongly discontinuous.

(It also merits mention that my macro rig includes three very powerful flash heads mounted around the lens front element. I've never observed dragonflies, wasps, bees, flies, or spiders to react to these in any way, even when firing from a distance of six inches; the only reaction I've seen has been from fall webworm caterpillars, which displayed a communal defensive response, and that may have been as much due to the shadow I cast, or to the polistid wasps hunting nearby, as to my flashes firing. The wasps notably did not care at all about me or my flashes, especially after they also found the nest and busied themselves with its rapid depopulation.)

Re:Teardown of a $1.25 LED Lightbulb by UnFleshedOne on Wednesday February 19, 2020 @01:00PM (#22368126)
We used to catch them by the wing by slowly approaching. Interestingly, medium ones were easy, but the big ones (different species, much rarer) wouldn't let me approach at all.
Re:Teardown of a $1.25 LED Lightbulb by throwanem on Wednesday February 19, 2020 @01:21PM (#22368366)
I mostly encounter eastern pondhawks and Halloween pennants, which are medium-sized and typically easy to approach.
Re:Teardown of a $1.25 LED Lightbulb by gibolt on Wednesday February 19, 2020 @01:19PM (#22368337)
Pigeons have a "refresh rate" of around 100 frames per second. It is believed that a bunch of smaller animals and even insects have similar or faster visual processing time, though I'm not aware of specific numbers.
Re:Teardown of a $1.25 LED Lightbulb by hinkley on Wednesday February 19, 2020 @12:03PM (#22367446)
I used to be able to detect the flicker by eye, or sometimes by waving my hand. But they pack so many into the demo display at the store that when I moved I had to use the slomo feature of my phone to pick the right LEDs.
Re:Teardown of a $1.25 LED Lightbulb by tootie on Wednesday February 19, 2020 @11:46AM (#22367229)
My cheaper LEDs also seem to get destroyed by a dimmer much quicker than better ones. Not sure if that's related.
Re:Teardown of a $1.25 LED Lightbulb by Dylan16807 on Wednesday February 19, 2020 @11:40PM (#22372717)
Probably not directly related. Dimmers cause voltage spikes, and cheaper models are less equipped to handle that.
Re:Teardown of a $1.25 LED Lightbulb by altcognito on Wednesday February 19, 2020 @11:00AM (#22366651)
At five times the cost, they had better be higher quality bulbs. $13 is pretty steep for a single bulb.
Re:Teardown of a $1.25 LED Lightbulb by timmytokyo on Wednesday February 19, 2020 @09:57PM (#22372330)
Has anyone done a comparison of flicker in available LED bulb brands?