News for hackers. Stuff that matters.
Re:A 3D Metal Printer Is Churning Out Rockets by magoon on Tuesday October 29, 2019 @08:11AM (#21386214)
When this technology can exist in space, earth will have orbiting shipyards building space craft.
Re:A 3D Metal Printer Is Churning Out Rockets by alehul on Tuesday October 29, 2019 @09:07AM (#21386650)
Orbiting shipyards seems like a likely bet (assuming we want to explore and interact with space).

If we want giant, heavy spacecraft that are capable of interacting with their environment — the space equivalent of a construction vehicle or a tank — earth's high escape velocity makes it impossible to launch from.

We'd instead need to construct it in space, even if all the materials were from earth.

As the cost of launching from earth continues to fall, it'll also become increasingly economically feasible to launch multiple payloads to build a larger, more complex spacecraft.

(Think of the assembly of the ISS as a proof-of-concept here [1]).

[1] https://en.wikipedia.org/wiki/Assembly_of_the_International_...

Re:A 3D Metal Printer Is Churning Out Rockets by ClumsyPilot on Tuesday October 29, 2019 @11:33AM (#21388299)
The entire point of construction in space is to avoid launching from earth. It takes 36 times less energy to get a ton of material from moon surface, and can be done without rockets at all - a space elevator can be built on the moon with 'normal' materials.
Re:A 3D Metal Printer Is Churning Out Rockets by alehul on Tuesday October 29, 2019 @12:53PM (#21389299)
> The entire point of construction in space is to avoid launching from earth

This is true, but avoiding launching from earth could be done for one of two reasons:

(1) to increase the efficiency of what can be built

(2) to increase the possibility of what can be built

Your point is (1), and I agree with it. The point mentioned above is (2) — even if all the materials for the ISS were from earth, it still could not be constructed on earth and then launched as a whole, and so construction in space is viable.

Re:A 3D Metal Printer Is Churning Out Rockets by tomatotomato37 on Tuesday October 29, 2019 @02:41PM (#21390627)
It would still be a good stepping stone to complete off-world industry; one of the reasons current space launches cost a lot is because you don't only want things in orbit but you want something in orbit intact and functional. A pallet of dumb steel ingots could be lopped up with something with much more generous tolerances ala the Big Dumb Booster[0], with any orbital maneuvering once up there accomplished by space tugs.

[0]https://en.wikipedia.org/wiki/Big_dumb_booster

Re:A 3D Metal Printer Is Churning Out Rockets by heavenlyblue on Tuesday October 29, 2019 @11:43AM (#21388419)
Why is Elon Musk aiming for Mars if building a solar panel array and all of the subsequent manufacturing industry on the moon could potentially be way more productive?

Is there something I am missing?

Re:A 3D Metal Printer Is Churning Out Rockets by ClumsyPilot on Tuesday October 29, 2019 @04:38PM (#21391713)
Mars is absolutely a better place to live, it's an actual planet.

But for industrial hub, the fact that we have the moon is an absolute miracle. We can build and refuel ships that dwarf our current ones. And we will need moon based factories if we are to make any meaningful progress is settling the solar system. The only things that should ever be lifted off earth is People/ other life, and super high-tech goods like microchips.

The Moon is also close enough to Earth that you can get help, or go back in case you suddenly need surgery. Good luck with that on Mars.

Settling Mars with our current ships is like settling Australia with a canoe.

Re:A 3D Metal Printer Is Churning Out Rockets by m4rtink on Tuesday October 29, 2019 @05:16PM (#21392126)
Indeed, yet there are various challenges inherent to Moon colonization, such as continuous direct surface impacts due to no atmosphere, extreme temperature surface environment due to 14 day days, lack of various elements (such as carbon or nitrogen), etc.

Still super useful & the short distance overrides much of the downsides.

Re:A 3D Metal Printer Is Churning Out Rockets by elihu on Tuesday October 29, 2019 @01:31PM (#21389791)
Mars is a more hospitable, Earth-like environment for humans. It has an atmosphere, a normal-length day-night cycle, less extremes of temperature, and closer to normal gravity.

Mars and the moon both have pros and cons. Mars would be an easier place to survive, but the moon is easier to get to.

Re:A 3D Metal Printer Is Churning Out Rockets by ClumsyPilot on Tuesday October 29, 2019 @04:53PM (#21391892)
The habitability difference is not relevant at this stage - both will kill you instantly. The ISS orbit has no atmosphere or gravity, but it's easier to keep people alive there than on Mars.

For a Moon base locations, look up peaks of eternal sunlight. We also have space-grade nuclear reactors and RTGs ready to go.

On the Moon you can have realtime communication, bring way more equipment, have robots remotely controlled from Earth, and get help or evacuate quickly. NASA and China will be able to land people on the Moon, other nations can get rovers/supplies there.

Anything goes wrong on Mars - you are dead. I would pick Moon any day.

Re:A 3D Metal Printer Is Churning Out Rockets by elihu on Tuesday October 29, 2019 @06:35PM (#21392840)
Mars has more resources available to work with and is a less extreme environment than the moon or space. There's definitely a trade-off between quick and easy access to the moon versus an easier environment to work with.

No one can survive in any of these places without a space suit, but on Mars you have easier access to the various natural resources you'd need in order to survive and build additional infrastructure. Light for solar power is consistently available on a normal day/night cycle, as is CO2 and water, which can be used to make methane fuel and liquid oxygen. It has concentrations of sulfur, which can be used to make a form of concrete. The gravity is more conducive to long term human health. All this is relevant.

Surviving on the moon or in LEO is also quite possible, it's just that you'd need to bring more equipment and all the resources you can't find on-site.

Re:A 3D Metal Printer Is Churning Out Rockets by hutzlibu on Tuesday October 29, 2019 @02:04PM (#21390204)
"Mars would be an easier place to survive, but the moon is easier to get to. "

Since it takes 6 months to get to mars and only 3 days to the moon and the only advantage for surviving on mars is the mini gravity, I really think we should start with the moon.

Re:A 3D Metal Printer Is Churning Out Rockets by elihu on Tuesday October 29, 2019 @03:24PM (#21391075)
It's not just the gravity. On the moon, you have to deal with 2 weeks of day and 2 weeks of night, which means having to deal with wide temperature swings and if you rely on solar you need very large batteries.

Mars also has an atmosphere which contains CO2, which is useful for making methane. It also has a lot of water. (The moon has water too, though it may be less abundant/accessible.)

Re:A 3D Metal Printer Is Churning Out Rockets by redblacktree on Tuesday October 29, 2019 @04:52PM (#21391870)
Could some of those downsides be mitigated by putting your base on a "pole"?

That is, are there locations on the Moon's surface where the sun is perpetually visible?

Re:A 3D Metal Printer Is Churning Out Rockets by m4rtink on Tuesday October 29, 2019 @05:19PM (#21392157)
There are just a few crater rims where this happens, not the full pole - but those do indeed get sunn almost all the time & border areas in perpetual darkness, which is also pretty useful (cryogenics, temperature gradient, etc.).
Re:A 3D Metal Printer Is Churning Out Rockets by elihu on Tuesday October 29, 2019 @05:38PM (#21392360)
Sort of; there are some spots that get sunlight almost all the time. (The moon has quite a bit of wobble, so it's hard to get to 100%.) That greatly restricts your choice of base locations, though. There may be other resources or geological features you might want to be close to that aren't convenient (lava tubes, water deposits, flat places to land, minerals that can be used as building materials, etc...).
Re:A 3D Metal Printer Is Churning Out Rockets by redblacktree on Wednesday October 30, 2019 @02:32PM (#21400935)
I suppose if our base is extensive enough, we could use those locations primarily for power generation and then transmit that power to more desirable locations for other tasks. Though I do realize that I'm talking about a lot of effort/time/money/resources.
Re:A 3D Metal Printer Is Churning Out Rockets by hutzlibu on Tuesday October 29, 2019 @06:27PM (#21392779)
Day and night cycle is an issue yes, and sure, for a long term self sustainable settlement, mars looks much better.

But in terms of setting up a base soon and building rockets for example ... the very short travel distance to the moon offsets any advantage the mars has

Re:A 3D Metal Printer Is Churning Out Rockets by NortySpock on Tuesday October 29, 2019 @12:57PM (#21389343)
Robert Zubrin argued that Mars has more lightweight bulk resources (water, carbon dioxide) twenty years ago, and at the time the moon was thought to be barren of such resources that are useful for starting a human colony.

Recently (in the last decade) water has been discovered on the moon, frozen in areas of cold permanent shadow in craters.

Also the current US vice president wants to go to the Moon. The previous president wanted to go to Mars.

Re:A 3D Metal Printer Is Churning Out Rockets by chasd00 on Tuesday October 29, 2019 @12:22PM (#21388912)
Musk has been talking more and more about the moon lately. Maybe he's thinking the same.
Re:A 3D Metal Printer Is Churning Out Rockets by whatshisface on Tuesday October 29, 2019 @12:57PM (#21389360)
The fact that NASA has a clear directive to spend an absolutely humongous amount of money on the moon over a relatively short time frame may have something to do with Elon Musk's interest.
Re:A 3D Metal Printer Is Churning Out Rockets by serpix on Tuesday October 29, 2019 @01:58PM (#21390142)
US military uses quite a ridiculously larger amount yearly. Nasa budget for going to the moon is insignificant compared to what is spent on war.
Re:A 3D Metal Printer Is Churning Out Rockets by baq on Tuesday October 29, 2019 @02:43PM (#21390644)
False dichotomy. Military budget that can be spent on Elon’s business is probably less than what NASA is prepared to spend on a proven Earth-Moon-Earth service.
Re:A 3D Metal Printer Is Churning Out Rockets by whatshisface on Tuesday October 29, 2019 @03:00PM (#21390809)
It's not a perfect false dichotomy, between people getting to keep their wealth and all of the things it could be spent on, there actually is a sum that has to balance to zero.
Re:A 3D Metal Printer Is Churning Out Rockets by imglorp on Tuesday October 29, 2019 @08:34AM (#21386392)
Is this assuming some of the materials are available there? This would make sense if you're getting fuel or metal from asteroids, moon's surface, etc and building ships near those. But in Earth orbit, you'll need to lift the shipyard, then the fuel, then the metal powder etc for sintering, so what would be the gain?
Re:A 3D Metal Printer Is Churning Out Rockets by mattlondon on Tuesday October 29, 2019 @09:22AM (#21386793)
You could construct things that wouldn't fit inside the nosecone of a launch rocket if you assemble them in orbit.

You could also repair/refit things without them having to go through re-entry and then be launched a second time E.g. replace damaged/worn out rocket cones or solar panels etc if you can build them in-situ. Imagine Earth-Mars shuttles that just go back and forth that would need maintenance

Re:A 3D Metal Printer Is Churning Out Rockets by adrianN on Tuesday October 29, 2019 @08:53AM (#21386531)
Lifting many small things is easier than lifting one Battlestar Galactica sized thing.
Re:A 3D Metal Printer Is Churning Out Rockets by jacquesm on Tuesday October 29, 2019 @10:15AM (#21387388)
Also, if it goes wrong the damage is limited, and likely fixable.
Re:A 3D Metal Printer Is Churning Out Rockets by mkl on Tuesday October 29, 2019 @08:53AM (#21386529)
Yes, you'd probably want to go get some asteroids. Even small ones can contain huge amounts of metals, and icy ones could be turned into fuel. There's a lot of potential, but it's all a bit out of reach for the moment. https://en.wikipedia.org/wiki/Asteroid_mining
Re:A 3D Metal Printer Is Churning Out Rockets by HeyLaughingBoy on Tuesday October 29, 2019 @02:25PM (#21390473)
Still, the concept of space mining is slowly becoming a thing: https://space.mines.edu/
Re:A 3D Metal Printer Is Churning Out Rockets by JoeAltmaier on Tuesday October 29, 2019 @09:12AM (#21386701)
Isn't moon dust mostly bauxite? (oxidized aluminum)
Re:A 3D Metal Printer Is Churning Out Rockets by mkl on Tuesday October 29, 2019 @09:22AM (#21386795)
Not exactly https://en.wikipedia.org/wiki/Geology_of_the_Moon. I think the problem with moon resources is the moon's gravity while forming was strong enough to pull metals like iron and nickel down into the centre where we can't get at them (they're on the surface a bit too, but not conveniently concentrated). Asteroids, on the other hand, can contain lots of accessible nickel, iron, cobalt, etc.

I'm no expert though!

Re:A 3D Metal Printer Is Churning Out Rockets by ben_w on Tuesday October 29, 2019 @09:48AM (#21387089)
Wikipedia looks like it says [0], by elemental concentration, roughly 42% oxygen, 21% silicon, 12% iron, 8% calcium, 7% aluminium, 6% magnesium, 4% other.

[0] Bar graph with insufficient labels: https://en.m.wikipedia.org/wiki/File:Composition_of_lunar_so...

Re:A 3D Metal Printer Is Churning Out Rockets by imglorp on Tuesday October 29, 2019 @10:22AM (#21387465)
Magnesium should be even better for some space apps. In fact, it would sinter better in a vacuum than air.

https://www.deepdyve.com/lp/wiley/sintering-of-magnesium-h06...

Re:A 3D Metal Printer Is Churning Out Rockets by rapunkill on Tuesday October 29, 2019 @09:13AM (#21386702)
How will the heat dissipate if there's nowhere for it to go?
Re:A 3D Metal Printer Is Churning Out Rockets by rtkwe on Tuesday October 29, 2019 @09:59AM (#21387221)
Heat can still leave parts in space by radiating the heat away. We don't usually think about it because it's generally much slower than convective cooling here on Earth but it does happen and doesn't require a medium to cool. It's the method the ISS uses to cool its interior for example. [1]

[0] https://en.wikipedia.org/wiki/Radiative_cooling

[1] https://science.nasa.gov/science-news/science-at-nasa/2001/a...

Re:A 3D Metal Printer Is Churning Out Rockets by MisterTea on Tuesday October 29, 2019 @03:55PM (#21391318)
Unfortunately it's too slow. I work with electron beam welders so this is an everyday problem as it takes place in a high vacuum (1e-3 Torr or lower). Though for welding it usually isn't a big issue as most parts are large enough to sink their own heat. For deep high power welds in material which can't sink the heat we attach copper heat sink blocks to soak up heat like a sponge or for extreme cases, circulated oil cooled heat sinks.

In space you can't vent to atmosphere or run the oil through a fan/water cooled radiator. So I'm thinking you'd have to build a heat reclaimer or high surface area radiator which uses an active cooling system like thermal pipes or circulated fluids like oil. But how does this adapt to different parts with odd shapes? Perhaps the printing would have to take place in a pressurized environment to facilitate cooling using gas and then figure out how to get rid of or recycle the waste heat.

Re:A 3D Metal Printer Is Churning Out Rockets by rtkwe on Tuesday October 29, 2019 @04:39PM (#21391732)
Depending on the conductivity of the material being used could you not have it sink it's own heat through conduction into a pad connected to a beefier version of the ISS ammonia to radiator cycle or combine it with a phase change cooler that melts wax into liquid then slowly radiates that heat away? Even in an atmosphere you have to deal with all that heat eventually.

Truthfully I don't think the best way would even be to try to 3D print the whole structure though just generic pieces that are then assembled into larger assemblies. Just being able to mass manufacture extruded profiles and sheet metal would allow you to do a lot in space that would be hard to launch piecemeal from the ground. Then smaller specialized pieces to join them together in the specific way required for the current vehicle being built could be printed and assembled.

There's a lot of neat research going on in assembling structures like that atm.

Re:A 3D Metal Printer Is Churning Out Rockets by trhway on Tuesday October 29, 2019 @06:57PM (#21392987)
>Unfortunately it's too slow.

well, it depends on the target temperature you want to maintain. Radiative power grows with the forth power of temperature (https://en.wikipedia.org/wiki/Stefan%E2%80%93Boltzmann_law). So that red glow of Merlin engines mentioned by the other comenter radiates so intensively that any other method of heat transfer can hardly come close. Another example - just 5700K of the Sun surface is enough to radiate away all the power the Sun's body generates.

Re:A 3D Metal Printer Is Churning Out Rockets by m4rtink on Tuesday October 29, 2019 @05:22PM (#21392188)
The upper stage variant of the Merlin engine used on Falcon 9 uses radiative cooling as well - that's why it's nozzle extension glows red hot - it cools itself that way! :-)
Re:A 3D Metal Printer Is Churning Out Rockets by allannienhuis on Tuesday October 29, 2019 @12:16PM (#21388836)
right, but the rate of dissipation would be a huge problem for the additive technique described in this article. Plus the lack of gravity means that the molten metal would adhere to the existing component very very differently. Essentially it would mean designing the process from scratch - with almost no ability to test on earth during the design process. Not sure how effective computer modelling is for that type of thing :)
Re:A 3D Metal Printer Is Churning Out Rockets by rtkwe on Tuesday October 29, 2019 @01:54PM (#21390087)
You can do small scale tests of each bit though: testing the sintered powder jet on a parabolic flight, test the heat dissipation in a vacuum chamber, etc. It wouldn't be easy but it's far from impossible.
Re:A 3D Metal Printer Is Churning Out Rockets by bryanlarsen on Tuesday October 29, 2019 @10:52AM (#21387798)
Thought experiment: how does the heat of the sun reach the earth?
Re:A 3D Metal Printer Is Churning Out Rockets by tantalor on Tuesday October 29, 2019 @12:20PM (#21388889)
We are closer now that the ISS has a functional 3d printer (looks like PLA)

https://www.nasa.gov/content/international-space-station-s-3...

Re:A 3D Metal Printer Is Churning Out Rockets by jvm_ on Tuesday October 29, 2019 @11:19AM (#21388137)
If you turn on a blowtorch in space, does it need some sort of kylo-ren double-action torch to keep it in place? I guess it won't move if it's anchored to something, but that something will still move as the force is unbalanced?
Re:A 3D Metal Printer Is Churning Out Rockets by klyrs on Tuesday October 29, 2019 @01:06PM (#21389459)
Probably safer to tether yourself to the thing you're blowtorching...
Re:A 3D Metal Printer Is Churning Out Rockets by honkycat on Tuesday October 29, 2019 @03:46PM (#21391251)
You could manufacture goods ( electronics, cars, etc. )in space, and then drop them onto Earth. Free shipping!
Re:A 3D Metal Printer Is Churning Out Rockets by travisporter on Tuesday October 29, 2019 @07:32PM (#21393220)
The reason relativity calls their rocket Terran 1 is they want to make “Ares 1/Luna 1“ someday :)