https://www.homedepot.com/p/Behrens-31-Gal-Galvanized-Steel-...
I use these as planters for my orchard fruit and nut trees. They have no open holes. I have to drill the bottoms or side to add drainage so that the trees don't drown.
That would probably work well with the lid on floor, bin over the top.
I work with an MR scanner. Bluetooth seems to work through the cage (or did on the previous scanner I used) and cellphone calls work though it fine as long as the door is just a tiny bit open.
It’s quite interesting to play with.
The cage drops signal 100db (well, that the spec it’s built to).
Rf leaks are the worst. You can run the scanner in a ‘detect rf’ mode to try find any leaks. They can be a pinhole, a faulty light, a poorly sealed escape hatch etc.
A bad one can take a very long time to find and it’s enormously expensive to do so.
The more time I spend with it the more incredible it seems that that it ever works.
While there may be imperfections in flatness on standard, uncarpeted floors that can allow RF signal to find a path inside (reflections from below or from other angles as another comment mentions) or you could live in a house like mine where flat had a non-standard definition with lots of slop, I believe that you solve those issues by setting the lid upside down on the floor, placing your apparatus inside the lid, then covering and sealing it with the inverted trash can.
You should have plenty of signal attenuation either way.
>Presumes the floor (or other surface) is perfectly flat...
with your reply to that comment:
>And that the floor will attenuate any reflected EMP/signal from underneath (should be small in a basement, but ...)
I believe that I addressed those issues in my reply to the other poster.
>Trash can lids are usually not so flat, which makes the whole thing wobbly.
Very true but simple to accommodate for even if the wobble has zero effect on its signal attenuation characteristics. If the can that I linked topples in the wind it will not affect the seal at all. That is a very durable can with a dependable grip on the lid.
>The ones you linked lack a handle on top, but it's a common feature on metal cans.
True that handles are common on trash cans. I buy that trash can specifically because it does not have a handle and therefore it has no holes or slits in the lid. The dish shape makes it suitable for use as a shallow, very durable bird bath or water feature for attracting bees and other insect pollinators. When you have a lid like that one you can get a cheap solar-powered floating aerator/sprayer and add a few rocks and a piece of weathered driftwood for perches. Bees, wasps, dragonflies, butterflies, moths, etc will make good use of the small fountain feature. Fountains that I have scattered on my place draw all kinds of insects and birds. A few weeks ago I had a snake slither over to one of them and spend a few minutes dipping its chin for a cool drink.
a passing wave, even a distant plane wave, will couple to the EM surface waves of the can surface.
also novices always home in and hyperfocus on reflectivity and transmission attenuation lengths, which works when done properly, but is a complete PITA without using absorbers.
simply placing an unopen plastic water bottle inside the cavity means that any EM energy that does make its way in, would be absorbed, instead of repeatedly reflecting from your perfect metallic reflector walls...
Consider a small 2D patch of metal sheet with some resistivity: any attenuated tails of EM waves will induce currents in the metal, and those currents can flow in all directions in the sheet.
Now consider the same metal sheet with a very fine unintentional slit, while currents can still run parallel to the slit, the metal doesn't admit significant current (ignore electron tunneling across the slit) across the slit, this means a current can circulate around the slit, this is why some of the commenters here point out the issues with slits. Simply placing mating metal lids / doors / ... against metal containers does not guarantee identical conductivity across the formed slit: imperfect planarity (think placing the Alps upside down on the Pyrenees), different metallic phases (annealing etc) at the surface, the spontaneous formation of an oxide layer (aluminum has a thin corundum layer, iron/steels/metals oxidize,...), protective coating layers, ... all contribute to the failure to text-book-reflect an EM waved with a perfect isotropic conductor.
Suppose you wish to protect your empire from an overrun by the barbarians: proper border control is important, but in practice imperfect, so you need a way to absorb or apprehend any barbarians that made their way in.
Thats why you want to place a wideband absorber within your protected cavity. This increases the demand on EMP power to disturb any sensitive devices.
Thanks for the added context about apprehending those barbarians that find their way inside the containment shield.
There would be no need to seal anything since the can has a continuous rolled seam. Just use a standard trash can instead of one of those kitchen trash cans that likely has a plastic bottom for easy clean-up.