This is not a user error, this is NVIDIA design error.
Broken by design.
I use always the cables that are shipped with the psu and noth the cables from gpu.
> Cable: 12V-2x6 = 12VHPWR No difference!
> So what does this mean if you’ve already got hardware for 12VHPWR? Fortunately, existing 12VHPWR cables and adapters will work with the new 12V-2x6 connector as the new changes are only related to the GPU and some PSUs (Our new RMx PSUs for example). The cables you've got already will work fine, so don't worry.
https://www.corsair.com/uk/en/explorer/diy-builder/power-sup...
From your link
> Compared to the original 12VHPWR connector, the new 12V-2x6 connector has shorter sensing pins (1.5mm) while the conductor terminals are 0.25mm longer
Either they are confident that the 0.25mm terminal difference is within tolerance enough that they consider 12VHPWR to be functionally equivalent to 12V-2x6, or they're getting themselves confused let alone the target audience of their article.
> As with any new standard, things are likely to evolve quickly and we’re now seeing the introduction of a new connector on the GPU and the PSU side of things. To be clear, this is not a new cable, it is an updated change to the pins in the socket, which is referred to as 12V-2x6.
Corsair's messaging on Reddit[1] emphasises this:
> Cable is the same. a 12VHPWR cable is a 12V-2x6 cable. it is ONLY the plugs on the graphics card / power supply that have changed.
> The cable is the same. 12VHPWR = 12V-2x6. You will get the exact same cable if you upgrade to a new PSU.
> As mentioned in image one, the cable is the same. Only the plug on the graphics card / PSU changed from 12VHPWR to 12V-2x6.
[1] https://www.reddit.com/r/Corsair/comments/1ha9no1/ive_made_s...
We really saying this when swapping a PSU to a different PSU and reusing existing cables that all look and plug in the same fries your build.
I think it's utterly absurd that this is the case but that's PC components for you.
Buildzoid and others have covered the design issues of the 12VHPWR cable and especially it's horrific implementation on the 5090FE well enough[1] that I don't think it's worth going into too much detail here. For some god forsaken reason, they decided to just dump all of the voltage lines in parallel and then run a single shunt resistor to it, so if a conductor fails and the load becomes improperly distributed, there's no way for the card or the user to know until it catches fire. It's hard to come up with a reasonable justification for this.
But just so we're clear, there are 2 reports of catastrophic failures with the 5090 already, which should be even more alarming considering how few 5090 actually exist right now. The other failure didn't involve third-party cables.
Of course, if used improperly, you can burn through basically any cable, and any cable can fail... but when the failure rate of a specific cable is so high above the rest, it raises many questions. If a specific model of aircraft seems to have an oddly bad problem with pilot error, you can't just shrug that off. In my opinion, consumer computer equipment is the same. It shouldn't light on fire unless you've done something horribly wrong. And even if you do something horribly wrong, the hardware should at least be designed in a way that gives it a chance at failing gracefully first. The connectors that 12VHPWR replaced were specced with good safety margins and previous NVIDIA cards were designed to ensure current was balanced across voltage lines.
It is unclear why NVIDIA didn't see the issue with the 12VHPWR last generation and put some serious effort into fixing the problem. If they continue recklessly like this, there is a non-zero chance that the 12VHPWR connector is only retired after it finally causes loss of life.
Also 12V-2x6 only changes the female connector on the card, the male end on the cable is unchanged.
End of the day PC power cabling is such a shambles with things that look standard but are not so you should only ever really use the cables that came with the product if you don't want to risk issues, especially with this specific ports poor history with 3rd party cables.