Yes, that's the thing I like about the Arlo system I have now: it has its own wifi network so, even if it's using spectrum, it's probably not affecting my LAN throughput.
> It's actually easier to run ethernet than power, especially outside.
This is true, but the house where I live already has power available everywhere I might need a camera. The thing I don't like about running new cables is the need to drill holes through exterior walls.
If the current setup can't, plugging the cameras and the NVR into a separate switch and none of that traffic will go near the rest of your LAN.
Wifi on the other hand, there's really no (practical) segregation to speak of - the spectrum has limited bandwidth, it doesn't matter if it's a different SSID / wifi network, it'll affect your Wifi!
For me: Wifi is great! But, whenever it's practical, I avoid it... Everything with it is a tradeoff!
A GbE switch with wire-rate transfer guarantee can handle 1Gbps traffic between arbitrary combination of ports. All the camera traffic coming from port 9 to 16 going to NVR on port 7 have no impact to traffic between upstream router on port 26 and your PCs on port 3 and 5. That cannot happen with Wi-Fi because everything is inherently on the same shared port 1(sometimes literally); each 4Mbps incoming is 4Mbps of download speed taken from your laptop. Double if destination is also on Wi-Fi.
This might be fine if there's just few cameras, but it's something to be aware of.
Wifi6 is changing a lot of this, but generally speaking Wifi performance is not optimized for media style traffic. Media traffic does best with low jitter (variance of latency) as this tends to keep buffer sizes low and avoids dropping frames. Wifi is not very good at low jitter, and though Wifi6 is a lot better than previous Wifi standards, it's still much harder to keep jitter low on Wifi than it is on a LAN. On top of that, as the sibling commenter says, even if you have a separate Wifi network, spectrum doesn't segment that neatly. Wireless traffic uses multiplexing methods (there are several and if you're interested, the methods are fascinating [1]) to roughly use the same spectrum. These multiplexing methods obviously need to do more work the more traffic there is on the spectrum.
If you can route your media traffic through LAN do it. Obviously as you say, running new cable is a lot of work so it's understandable why you use Wifi. But LAN is just so much better that if you have the time/money (doing it yourself/hiring someone) to do it, I highly recommend you do.
Unless you're using dedicated APs it is absolutely affecting your other wifi users.
Chances are, a single switch is more cost effective than multiple injectors. But you also need Ethernet routed throughout your house. One alternative is to have the G.hn (powerline) adapter with PoE. This way, you can be both network and power with one plug without wiring your house.
Edit: not sure why you’re being downvoted
Frigate links some Dahua camera recommendations in their documentation: https://docs.frigate.video/frigate/hardware/
I installed them and they've been rock solid. Low light performance is excellent. The turret form factor is nice and unobtrusive.
I found that one key type is for wifi daughter cards so I was able to save a pcie slot or nvme slot using that in the small form factor host.
I would not use WiFi cameras. Standard RTSP PoE h264 is the way to go.
For PoE, I'd just do whatever is convenient. I've done setups with 2 PoE switches before so I could just run one cable and then branch out from there.
Wifi cameras are more for convenience than reliability or dependancy.
It basically doesn't matter at all - I have a mixture of both in my home, multiple PoE switches and multiple PoE injectors for things like cameras, wireless APs etc. Use whatever fits needs/budget/location, you don't have to go nuts buying a single high end PoE switch. There's often good deals to be had on used PoE switches on ebay etc too if really budget conscious.
The only real advantage of going with a single or fewer PoE switches is you have less things to put on a UPS, if you require the system to still work when power goes down. A UPS that can run say 4 cameras, the PoE switch and a system running Frigate for more than a few hours can get pretty expensive too, in my experience - most cheap UPSes are designed to get you enough power to save some files and shutdown a PC in a matter of minutes, not hours.
Cheap intel box with a Coral runs Frigate fantastically, and if a tower build plenty of room for internal storage drives.
I've gone the other route, with a simple power supply that charges an ever-evolving fleet of whatever cheap 12-volt batteries aren't doing anything else, which then feeds DC-DC converters for the various loads. For stuff that's natively 12-volt like my wifi router and cable modem, I just run those directly off the battery rail.
This setup is quiet, efficient, and presently runs the modem, router, service pi, and my RIPE Atlas probe, for somewhere upwards of 20 hours, for something like $150. If I added a 12v-to-48v converter and a small PoE switch feeding a few cameras, it would probably cut the runtime in half, but I could just throw more battery at it for pennies on the watt-hour.
- an intel-based PC (can be a minipc, doesn't need a powerful CPU)
- a USB Coral TPU ($60)
- some wired PoE cameras (from $60 each)
My question: what do people typically use to power the cameras? A single PoE switch, or multiple PoE injectors?
My Arlo Pro 2 cameras are apparently EOL and might stop receiving free cloud services in a couple of months. So this seems like a good time to upgrade to higher resolution cameras.
(The Frigate docs advise against using Wi-Fi cameras, which would otherwise be my preference.)