News for hackers. Stuff that matters.
Re:Sennheiser HD 555 to HD 595 Mod by thejosh on Sunday June 18, 2023 @06:41AM (#36378989)
AMD's Phenom II let you unlock the locked fourth core, if you so dared.. allowing you to save like ~$50 on the higher chip. But it could be unstable.
Re:Sennheiser HD 555 to HD 595 Mod by JonathonW on Sunday June 18, 2023 @08:36AM (#36379702)
Or it might not work at all (as was the case for mine when I tried it).

There definitely was a period where AMD was shipping three-core Phenom IIs with a functional fourth core (demand was higher for the three-core SKUs than their actual defect rate appeared to allow), but I don’t know how plentiful fully-functional one’s actually were. And it was never guaranteed.

Re:Sennheiser HD 555 to HD 595 Mod by nailer on Sunday June 18, 2023 @08:56AM (#36379890)
There was also the original Athlon, where there was an unjoined connection on top of the die. You could fill in the connection with a pencil and overclock the chip.
Re:Sennheiser HD 555 to HD 595 Mod by partomniscient on Monday June 19, 2023 @04:08AM (#36388515)
Been there and done that.

"By the power of graphite!", I upgraded my cheaper CPU to a more expensive one.

Skeletor failed to show, however.

Re:Sennheiser HD 555 to HD 595 Mod by sf_rob on Sunday June 18, 2023 @08:58AM (#36379905)
Yes, allegedly demand outstripped supply for the lower core count chips so it was a mix of disabled rejected cores and disabled working cores.
Re:Sennheiser HD 555 to HD 595 Mod by accrual on Sunday June 18, 2023 @10:11AM (#36380450)
Two other older AMD CPUs could be similarly unlocked:

- AMD K6-2+ with 128K of L2 cache can be converted to a K6-3+ with 512K. The CPU has a heatspreader that can be carefully removed revealing a series of zero-ohm resistors, moving it to the right location unlocks the cache. The CPU is still bound by binning as to whether or not it can be overclocked well.

- AMD Athlon XP could be overclocked with the "pencil mod", using a pencil to draw a conductive trace between two pads on top of the CPU, no delidding required.

Re:Sennheiser HD 555 to HD 595 Mod by craigmcnamara on Sunday June 18, 2023 @11:18AM (#36381045)
Isn’t a zero ohm resistor just a jumper?
Re:Sennheiser HD 555 to HD 595 Mod by tialaramex on Sunday June 18, 2023 @11:21AM (#36381077)
In a sense that's correct, but "jumper" suggests these are deliberately components you can change whereas "Zero ohm resistor" is likely intended to be permanent.
Re:Sennheiser HD 555 to HD 595 Mod by cwillu on Sunday June 18, 2023 @12:51PM (#36381927)
In PCB manufacturing, a jumper wire is just a wire soldered between two points. A designer might or might not install jumper pins like those you refer to.

Regarding the use of a 0-ohm resistor instead of a jumper wire: wires are rather annoying to deal with in pick-and-place machines, while a 0-ohm jumper can be reel-loaded like any other part.

Re:Sennheiser HD 555 to HD 595 Mod by joezydeco on Sunday June 18, 2023 @11:23AM (#36381092)
It is, but pick-and-place robots like to work with zero ohm resistors compared to small pieces of wire. Also makes it easier to change later, you just swap reels.
Re:Sennheiser HD 555 to HD 595 Mod by sireat on Sunday June 18, 2023 @11:08AM (#36380955)
I still have a computer running Athlon x3 unlocked to Phenom x4 - circa 2010 this was the most cost efficient way to get a 4 core with 32GB of RAM.
Re:Sennheiser HD 555 to HD 595 Mod by 404mm on Sunday June 18, 2023 @12:20PM (#36381620)
You don’t even need to look for extra cores. Just CPUs being locked on different frequencies is similar enough to this concept.
Re:Sennheiser HD 555 to HD 595 Mod by manmal on Sunday June 18, 2023 @05:07PM (#36384477)
And certain GeForces could be turned into Quadros (for use with CAD software): https://archive.techarp.com/showarticleefc1.html?pgno=0

This was a soft mod, but I think there was also a hardware mod involving only a pencil.