News for hackers. Stuff that matters.
Re:Soldering Wires – Here's a different way by Whitespace on Tuesday September 27, 2022 @02:37PM (#32999282)
If you have that many stripped wires to tin, you can use a tub of flux and a solder pot. Dip the wires into the flux, then quickly dip it into the solder pot. Perfectly tinned end with no plastic melting. Really hard to mess up vs a soldering iron, a wire, and solder wire.

You can even dip multiple wires into the flux and solder bath at the same time, as well as use the flux tub again before you solder the tinned wire to the contact.

Re:Soldering Wires – Here's a different way by mdturnerphys on Tuesday September 27, 2022 @04:40PM (#33000825)
And if you have a lot of wires to strip, get a compound automatic wire stripper or a laser wire stripper.
Re:Soldering Wires – Here's a different way by lagrange77 on Tuesday September 27, 2022 @04:48PM (#33000905)
There are laser wire strippers? Shut up and take my money.
Re:Soldering Wires – Here's a different way by mdturnerphys on Tuesday September 27, 2022 @04:58PM (#33001025)
Re:Soldering Wires – Here's a different way by rkagerer on Tuesday September 27, 2022 @09:02PM (#33003130)
Awesome. How do they know when to "stop"?

EDIT - found the answer:

> Because the metallic conductor is essentially a mirror at the wavelength of the laser, the process is effectively “self terminating”, that is the laser vaporises all of the insulating material down to the conductor and then stops, so no process control is required to prevent damage to the conductor.

Re:Soldering Wires – Here's a different way by linkdink on Tuesday September 27, 2022 @09:18PM (#33003228)
> The Mercury-4 is the culmination of years of research

I'm imagining some researcher after years of investment and experimentation eventually accidentally discovering the solution: "you mean it just shuts _itself_ off?!?!".

Re:Soldering Wires – Here's a different way by exmadscientist on Tuesday September 27, 2022 @09:30PM (#33003296)
It doesn't shut itself off. It just stops cutting. It's like using concrete as a kitchen cutting board: that knife isn't going to do any damage, regardless of whether or not you stop pushing.

If you want to laser through metals, you need a different type of laser. Just as getting through concrete needs a different tool (say, a hammer chisel).

Re:Soldering Wires – Here's a different way by linkdink on Wednesday September 28, 2022 @03:22PM (#33012072)
The line sounded funnier to me in the less pedantic way.
Re:Soldering Wires – Here's a different way by bombela on Wednesday September 28, 2022 @12:15AM (#33004188)
Not a really good comparison I think.

A knife blade and a masonry chisel are roughly the same type of carbon steel tempered to a similar hardness.

They will both scratch and damage concrete.

Re:Soldering Wires – Here's a different way by exmadscientist on Wednesday September 28, 2022 @02:12AM (#33004749)
I'll grant that it's an imperfect analogy!

But would you like to chop through my sidewalk to get to the water main with a santoku?

Re:Soldering Wires – Here's a different way by mdturnerphys on Tuesday September 27, 2022 @09:18PM (#33003229)
This and the wire is able to conduct the heat away faster than it is deposited into it. With some very thin phosphor bronze wires I have seen damage.
Re:Soldering Wires – Here's a different way by bbarnett on Tuesday September 27, 2022 @07:09PM (#33002302)
This... how, why, what? It has to be fake. Right?

We're supposed to be using lasers to ... well, shoot at space ships, not cut plastic wire wrapping!!

Re:Soldering Wires – Here's a different way by techdragon on Wednesday September 28, 2022 @12:08AM (#33004154)
When all you have is a laser, every problem looks like something to be ablated.
Re:Soldering Wires – Here's a different way by mechanical_bear on Tuesday September 27, 2022 @08:43PM (#33003010)
That has to be expensive.
Re:Soldering Wires – Here's a different way by lagrange77 on Wednesday September 28, 2022 @05:11AM (#33005963)
Re:Soldering Wires – Here's a different way by duped on Tuesday September 27, 2022 @03:31PM (#32999989)
Totally true, but you don't always have a solder tub or tub of flux laying around. The other advantage of this approach is it's easier to avoid tinning under the insulation
Re:Soldering Wires – Here's a different way by denkmoon on Tuesday September 27, 2022 @08:22PM (#33002882)
What is the impact of tinning under the insulation?
Re:Soldering Wires – Here's a different way by userbinator on Tuesday September 27, 2022 @11:41PM (#33003993)
Makes stranded wire turn solid and likely to break at that point.
Re:Soldering Wires – Here's a different way by bsder on Tuesday September 27, 2022 @03:21PM (#32999861)
Yeah, every time I see a soldering "tutorial" that doesn't use separate flux--I facepalm.

Flux is probably more important than the solder for good joints. A syringe of paste flux makes life ridiculously easier.

Re:Soldering Wires – Here's a different way by gw99 on Tuesday September 27, 2022 @03:40PM (#33000127)
I did several years in production engineering. We never used flux. Not once. It’s a crutch for people who don’t know how to solder.

What we did was use solder that wasn’t shitty. Big fan of felder 62/36/2 but it ain’t cheap.

We also cleaned stuff properly before soldering it. The reason people tend to flux things to death is that they didn’t clean the oxide layer off before soldering. Or used shitty solder.

Re:Soldering Wires – Here's a different way by bitdivision on Tuesday September 27, 2022 @05:06PM (#33001120)
felder 62/36/2 [0] is a flux-cored solder. So you were using flux every time.

It's also a leaded solder, which is much easier to get nice joints from than lead-free.

Flux is great, adding some before you solder is a good tip, and will likely help you make better joints if as you said, you haven't perfectly cleaned everything. The only downside is perhaps some more cleanup afterwards. There's no reason to disparage it's use.

0: https://www.felder.de/products/electronic-applications/manua...

Re:Soldering Wires – Here's a different way by gw99 on Tuesday September 27, 2022 @05:24PM (#33001318)
Yes it’s additional flux that you don’t need.
Re:Soldering Wires – Here's a different way by OJFord on Tuesday September 27, 2022 @06:42PM (#33002084)
So flux is 'a crutch for people who don't know how to solder', because that knowledge would lead you to use 'expensive' flux-cored solder instead of 'shitty solder' plus flux?

I really don't think either's wrong, and anyway I assume 'production engineering' is not using how-to-solder tutorials.

Re:Soldering Wires – Here's a different way by gw99 on Wednesday September 28, 2022 @02:23AM (#33004815)
Shitty solder + flux is wrong. Simple.

That is part of production engineering which is mostly about making sure that your product doesn't come back again because it's broken.

Re:Soldering Wires – Here's a different way by OJFord on Wednesday September 28, 2022 @07:15PM (#33014421)
Yes, you're concerned with the yield on tens, hundreds of thousands of boards.

It's a different world from a hobbyist's one-off project. This advice was never intended for you, and appropriate advice can differ between audiences.

Re:Soldering Wires – Here's a different way by randombits0 on Tuesday September 27, 2022 @05:33PM (#33001397)
Depends. New work versus rework versus what-is-this-piece-of-crap?
Re:Soldering Wires – Here's a different way by exmadscientist on Tuesday September 27, 2022 @09:33PM (#33003313)
Ding ding ding. Production soldering isn't easy, but it's much easier to dial in than rework jobs. It's definitely a desirable goal to not need flux for production work.

Rework... good bloody luck.

Re:Soldering Wires – Here's a different way by lightedman on Wednesday September 28, 2022 @12:18AM (#33004203)
I most certainly do not use flux in my rework. I am in a zero-clean facility, the only flux allowed is that which comes with the solder paste for stencil and SMT placement - on initial production work.

Fluxless rework isn't difficult at all. I do it dozens of times a day.

Re:Soldering Wires – Here's a different way by exmadscientist on Wednesday September 28, 2022 @02:10AM (#33004745)
I'm having a little trouble believing you unless by "rework" you meant "reflow".

Production reflow without extra added flux is normal. It's the goal for every assembly line anywhere and is almost always achieved.

Rework of existing joints after assembly without flux is just about impossible. The oxidation of the joints guarantees it. Many times the flux in the paste or wire is sufficient, but this is more true for through-hole than for surface-mount, mainly due to joint geometry and available volumes. If you are regularly reworking old fine-pitch surface mount joints previously assembled with no-clean flux, without flux of your own... then I'd like to know what materials you're using, because that is not possible in general. The "no-clean" fluxes are notorious for causing rework trouble, and they are difficult to clean off once reflow temperatures have been achieved (that's why we call them "can't-clean"). They are never active twice, so they must be removed and replaced once heated the first time. We have to use special solvent flux removers around here (based on DuPont's hellish Vertrel XF) to get the crap off just to be able to access joints again. (This is on assembly work done out-of-house or on COTS devices, made with who-knows-what.)

Re:Soldering Wires – Here's a different way by lightedman on Sunday October 02, 2022 @08:40AM (#33055411)
"I'm having a little trouble believing you unless by "rework" you meant "reflow"."

Nope, we don't use flux at all for rework. As the majority of our boards are solid metal, we just slap them on a heater and poke the components down or slide them into place. Flux isn't needed. Even with crappy RoHS tin solder. If you're getting significant-enough oxidation that interferes with rework with the product fresh out of the oven, or even a day or two later, you're doing something extremely wrong. Check and make sure your production paste isn't contaminated.

Re:Soldering Wires – Here's a different way by linker3000 on Tuesday September 27, 2022 @05:05PM (#33001106)
"It’s a crutch for people who don’t know how to solder."

This needs shouting from the rooftops.

So many people get sucked into the groupthink on this; yes it helps with less-than-perfect beginner's soldering skills, but it should not be normalized.

Flooding every joint with extra flux is unnecessary and a waste of money.

/Pet peeve (well, one of them!)

Re:Soldering Wires – Here's a different way by randombits0 on Tuesday September 27, 2022 @05:37PM (#33001447)
We all don’t get to work on nice, new, shiny PCBs. Sometimes other things get in the way. I have three different kinds of flux, two types of solder, copper wick, three solder suckers, two guns, and a scratch pen. I’m not out to practice the art, I just want to be effective.
Re:Soldering Wires – Here's a different way by bsder on Tuesday September 27, 2022 @10:27PM (#33003609)
Sorry, I'll fight you very strongly on this.

Most soldering that relies on effects from solder surface tension simply will not work without quite a bit more flux than you can get from the core of a solder wire. Drag soldering, for example, won't work on quad flat pack chips without quite a bit of flux.

And while my techs will absolutely back you up that my soldering skill sucks, to a person they ALL use solder flux for their soldering. Not even a single exception. And they're all trained to NASA aerospace standards.

Now, maybe you can be more skilled than they are and get away without using solder; however, back down here in reality, the rest of us punters will just add flux when soldering stuff, thanks.

Re:Soldering Wires – Here's a different way by wolfendin on Tuesday September 27, 2022 @06:40PM (#33002066)
Yeah, I’ve been soldering for something on three decades now and the only time I need flux is removing parts on ancient boards.

More flux that what comes with the solder isn’t necessary with good technique.

Re:Soldering Wires – Here's a different way by buescher on Tuesday September 27, 2022 @05:09PM (#33001158)
I agree up to... new parts shouldn't need cleaning. And cheapo hobbyist-grade RF and audio connectors often have a weird chrome + some kind of oil or varnish surface finish that just won't clean off or solder and flux is a godsend for those.

That said, I let someone borrow my bottle of liquid flux about a decade ago and have never bothered to replace it.

Re:Soldering Wires – Here's a different way by an_aparallel on Tuesday September 27, 2022 @08:31PM (#33002936)
solder pots!! Thank you for your comment :) This is awesome. i dont know why i've never seen these before.