A sharply cutting off analog filter is expensive to produce. It has multiple stages to create the multiple poles. High precision resistors and capacitors have to be used to get all those circuit stages to line up. The filter will have phase distortion.
That's the basis of "supersampling": sampling at a higher rate with a simpler filter with less of a cutoff, then completing the job with a digital filter to get to the target sample rate.
This can be done in reverse, in reproducion. Take, say, a 48 KHz signal, and digitally interpolate it to a higher sample rate like 96 KHz. That is fed to the DAC. The filter after the DAC then doesn't need such a steep cutoff after 20 KHz. A greater bit depth can be used; like 16 bit samples interpolated to 24 bit at a higher rate, fed to a 24 bit DAC.
The digital filter or interpolator doesn't care about accurate resistors, capacitors or drift in component values over time or due to heat; it does the same thing with the same data every time.
Digital filters can look at future values also. The state of an analog filter is determined by only the current and past values of the signal; but digital signal processing can delay the signal a little bit and look at a "box" around the current value. I think that is key to preserving phase relationships.
This is incorrect. See my comment above/below.
Monty (of xiph) has an article on the subject (well on 24/192 but it applies all the same) which goes into the gory details: https://people.xiph.org/~xiphmont/demo/neil-young.html
There's a space in the audio world for more bits of data. But the final output format isn't where it belongs.
If you're sampling at 48 kHz, the signal has to be severely attenuated already; it has to go from 20 kHz to deep cutoff in just the space of a few kHz.
At 96 kHz can achieve the effect as if you were sampling at 48 kHz, with a steep filter. You sample at 96 kHz with a milder filter, and then purely in the digital realm, you down-sample to 48 kHz. There is an overall filter consisting of the original analog one plus the digital processing.
That is cheaper and more reliable than doing it all in analog.
An analog filter with a steep cut off will be challenging in mass production because of the strict component tolerances.
Sure, you could use a steep filter with 96 kHz also. Say, a steep filter that starts cutting off at 30 kHz. It would still be a less demanding filtering application because of the margin that you have in the frequency domain. The multiple poles of the filter don't have to be lined up as well. E.g. if the first pole starts rolling off at around 30 kHz, and then next ones at 31, and the third one at 28, ... it doesn't matter because you're still hitting the absolute target of there being next to nothing at 48 kHz, and nearly the full signal at 20 kHz.
I believe the comment you're responding to is talking about the analog filter that is needed to avoid aliasing -- as the first words of your comment correctly note/explain.
And in particular, the original comment seems to be noting the phase distortion (in frequencies near the cutoff) that analog brick-wall filters will cause. This has been a design contention for decades, really, ever since the CD format was introduced.
It's a big design space, with options for gentler analog filters, followed by very fast digital sampling, and further tricks with filtering in the digital domain, where you don't have to worry about getting great capacitors, etc.
It may be out-of-scope to lay all that out in one paragraph!
You're right that its a big design space. The key takeaway is that "yes, higher sample rates can actually make a difference, but almost entirely down to the filter design, not because Nyquist moves ... and you probably cannot hear the difference."
Its vwry “spherical cow”. It assumes all your filters, DACs, are perfect, and that time is infinite.
Yes, your filters, DAC and speaker wire could still create a less than ideal listening situation, but the fundamental aspect of the Nyquist frequency is not concerned with any of that.
And you can use oversampling to correct for the filtering issues. That's pretty standard in modern DACs and ADCs.
With 96khz sampling rate, you don't need as a sharp drop off in your filter.
The above is mostly accurate, hopefully someone else will comment and tell me how I'm wrong and correct the inaccuracies.
Edit: to anyone reading this, read the replies if you want the correct explanation. To everyone that replied, thank you :).