News for hackers. Stuff that matters.
Re:We are starting to operate our CNC machines remotely by megraf on Friday February 19, 2021 @11:10AM (#26194586)
I moonlight at a machine shop. I'm not a machinist, and I'm hardly a machine operator.

Machine shops need bodies to do a few things (some of which OP mentioned) loading materials, removing materials, changing broken cutting bits, cleaning the machines (especially if you're cutting something like magnesium).

Machine shops also need bodies to build jigs to hold pieces to the machine table while the machines remove material (think 5 axis pieces, especially).

Despite all of this – there's an amazing amount of automation at play. Tool changes, coolant, temperature monitoring, the list goes on. I'm currently building some automation hardware and software so we can start to fill the gap of 'dead' time where machinists are pressing buttons, loading in blanks, and are bored out of their minds.

It's such an interesting space.

Re:We are starting to operate our CNC machines remotely by ortusdux on Friday February 19, 2021 @12:19PM (#26195356)
A few years back I toured a machine shop staffed primarily by blind individuals. The Javits–Wagner–O'Day Act requires federal agencies purchase some select goods made by the blind when possible. Roughly three hundred employees, 90%+ somewhere between legally blind and fully blind, and 1/3rd or so also deaf.

Someone more skilled than I could and should fill a book with the accessibility changes they have made over 50 years of operation. Every single inch of the place had fascinating design details. All machines were laser fenced. Vacuum work holding with audio alignment sensors. All paths had a raised curb. All readouts on CNCs were capable of displaying text one 15" tall letter at a time, or reading G-code aloud or via braille. All offices have one bright wall and one dark wall to provide high contrast for sign language interpreters.

One of the sighted employees I met works in the accessibility dept. redesigning systems to be compatible with various disabilities. He had a full lab of 3d printers, CNCS, and enough other equipment to make a makerspace jealous.

The company also did some amazing outreach through their charity. The provided dogs, housing, and general mobility training (how to navigate busses, etc.).

I should check in and see how they are coping with covid.

Re:We are starting to operate our CNC machines remotely by laurent92 on Friday February 19, 2021 @06:10PM (#26199286)
You see, it’s quite useful to talk about it, I was looking for a charity/NGO/open-source software to sponsor and, for a specific reason, Postgres or Debian (which we use) don’t comply to our requirements. You are giving me a new group of charities/social companies to search into.
Re:We are starting to operate our CNC machines remotely by zachrose on Friday February 19, 2021 @12:28PM (#26195465)
What was this company? That sounds amazing.
Re:We are starting to operate our CNC machines remotely by ortusdux on Friday February 19, 2021 @12:42PM (#26195654)
The Lighthouse for the Blind. I donate to their charity annually.

Here is a link to a virtual tour of the facility I visited: https://www.youtube.com/watch?v=zzfCNQatw00

Re:We are starting to operate our CNC machines remotely by calvinmorrison on Friday February 19, 2021 @04:14PM (#26198111)
This is absolutely the coolest thing I have seen so far this year. They have more videos where individual works explain how the work from a call center operator to a machinist journeyman!
Re:We are starting to operate our CNC machines remotely by tsss on Friday February 19, 2021 @01:28PM (#26196233)
Is laser fencing not mandatory in the US?
Re:We are starting to operate our CNC machines remotely by profsnuggles on Friday February 19, 2021 @02:28PM (#26196979)
Laser fencing is the worst, pressure mats are approximately 1000x better. Our machine with the laser fence is always stopping for no reason because there was some dust. I just cut 50 sheets of MDF yea there is going to be some dust.

In woodworking the new trend is to put pads on the gantry with pressure sensors so if the machine smacks you it stops.

That is really great when you are testing new programs you can see what is happening without binoculars. The only downside is that they limit the max rapid speed on the machines so when it hits someone they are much less likely to get knocked over.

Re:We are starting to operate our CNC machines remotely by bluGill on Friday February 19, 2021 @04:55PM (#26198521)
How do those systems stop hair or clothing from getting sucked into the spinning bits? Those two modes have always been the more dangerous ones for spinning tools.
Re:We are starting to operate our CNC machines remotely by profsnuggles on Friday February 19, 2021 @05:05PM (#26198637)
The gantry is enclosed, it's not possible to get close to the router unless you are doing something really... really wrong.

This is the machine I was running like 20 minutes before posting that comment. https://www.youtube.com/watch?v=7AuwwPdBSf8

I have no idea why the people in that video cut a hole in their door. Seems like a really stupid idea to me. But you can see in a normal machine that someone hasn't modified to be more dangerous you can't get to the the spiny sharp bits.

Re:We are starting to operate our CNC machines remotely by DarkStar851 on Saturday February 20, 2021 @12:39AM (#26201921)
Looks like that video was a demonstration from a company that sells these machines. The hole was just cut out for doing videos like this I'd assume, not a modification for regular use.
Re:We are starting to operate our CNC machines remotely by profsnuggles on Saturday February 20, 2021 @04:11AM (#26202844)
Yea but in the US at least if OSHA, or way more likely our insurance when they doing their yearly inspection saw that they would freak out. That company looks like they are German, and from what I've heard Germany is way more strict about safety than the US.

So in order to sell that machine to me I would require a safety compliant door. My guess is a new door would be around $2800. That is an expensive hole.

What I know that you don't is that that machine is sold with a camera as an additional option. So there is already a place inside for mounting a camera. They would just need to make their own mount. Otherwise if I was just filming a demo to sell the machine I would override the door closed safety interlocks and film with the door open temporarily.

Re:We are starting to operate our CNC machines remotely by aj7 on Friday February 19, 2021 @01:49PM (#26196469)
No not in ordinary machine shops.
Re:We are starting to operate our CNC machines remotely by oauea on Friday February 19, 2021 @01:11PM (#26196015)
Wow, that sounds incredibly inefficient and unsafe.
Re:We are starting to operate our CNC machines remotely by benlivengood on Friday February 19, 2021 @01:28PM (#26196227)
Humans are inefficient and unsafe machines, to be sure. Soft and fragile, slow to respond, 98% blind to the EM spectrum, insanely low communication bandwidth, unusually difficult to motivate, prone to acts of defiance, uncalibrated and wandering accelerometers and rotation sensors, very low precision parts, require a host of special atmospheric and environmental conditions to be met, etc.

We're replacing them as fast as we can, honest.

Re:We are starting to operate our CNC machines remotely by burnte on Friday February 19, 2021 @03:22PM (#26197584)
The problem with replacements is the installed base is HUGE.
Re:We are starting to operate our CNC machines remotely by earleybird on Friday February 19, 2021 @03:30PM (#26197681)
And they self-replicate - but we're working on that too.
Re:We are starting to operate our CNC machines remotely by neolog on Friday February 19, 2021 @03:01PM (#26197373)
Nice one.
Re:We are starting to operate our CNC machines remotely by bluGill on Friday February 19, 2021 @02:27PM (#26196968)
I didn't catch anything unsafe. They have laser trip wires anywhere things might be dangerous. This is becomming common industry practice anyway because even people who can see can miss seeing something - a common problem when doing repetitive tasks is to make it faster and faster without realizing that you are getting closer and closer to something unsafe until you loose your arm.

It isn't clear how inefficient they really are. Sure it takes longer to explain to a blind person who to clean the chips off, but in the end it is just a broom (vacuum?) and the only need to do ensure they get everything. Once you train them they have it. Likewise it takes a little longer to explain where the hold downs are then to explain it, but not that much and there are good reasons for hold down placement so once the blind person learns the location there isn't much more training.

I assume they have a few sighted people around for the unique setups that are not enough like something else that it be put into brial. (deaf but not blind can be good at this)

Again back to my first point: everything they pioneer and make work is something that other industry will be interested in as well. Maybe someone with sight can do it easily today, but often once they perfect a method it is better than what the sighted person can do.

Overall I'd prefer to not be doing manual labor myself, but if you can't handle enough school to get a good degree... I'm glad places like this exist for those who need it.

Re:We are starting to operate our CNC machines remotely by ortusdux on Friday February 19, 2021 @03:47PM (#26197852)
Exactly. They are actually efficient enough to be quite competitive in the private sector. They have large contracts with Boeing, and they manufacture a wide variety of things like white boards, backpacks, shovels, canteens, etc.
Re:We are starting to operate our CNC machines remotely by andrepd on Friday February 19, 2021 @01:18PM (#26196096)
Many things are "inefficient", such as building stairs and a ramp where just stairs would be cheaper. Then again there's more to life than that.
Re:We are starting to operate our CNC machines remotely by ska on Friday February 19, 2021 @04:47PM (#26198444)
> Wow, that sounds incredibly inefficient and unsafe.

Only if imagine an unrealistic system where these people were asked to adapt to an existing shop floor, rather than the other way around.

Re:We are starting to operate our CNC machines remotely by klyrs on Friday February 19, 2021 @09:09PM (#26200802)
That's weird, it sounds incredibly safe to me. I've never been in a machine shop that would be safe enough for blind people to work. OTOH, my mom was responsible for keeping factories safe for the workers who hadn't lost their hearing yet...
Re:We are starting to operate our CNC machines remotely by imtringued on Friday February 19, 2021 @06:36PM (#26199524)
Is it less efficient than no employment at all?
Re:We are starting to operate our CNC machines remotely by bordercases on Friday February 19, 2021 @01:13PM (#26196041)
On what metrics?
Re:We are starting to operate our CNC machines remotely by dwohnitmok on Friday February 19, 2021 @11:36AM (#26194863)
Many moons ago I also spent a fair amount of time in a machine shop, although never more than in an amateur capacity (I'm not sure I'd call what I did even moonlighting, mainly an enthusiast making small stuff), and I was never using really fancy machines as a result.

What struck me was how just how little was automated, how stuff that was nominally automated still had quite a bit of manual labor. I had always had in my mind that with CNC machines you just stick the metal in the vise, load the program, hit start, and you're good to go, but there's manual calibration, facing off and the like that needs to be done before every run.

For small, simple pieces I would often forgo the CNC automation and just manually make the piece myself, even when I had already made the piece in SolidWorks (and so could easily generate G code).

I've heard that for really fancy machines it's truly a push button process (as long as you feed it precision milled blanks), but I've never had a chance to actually use those.

Re:We are starting to operate our CNC machines remotely by extrapickles on Friday February 19, 2021 @12:49PM (#26195722)
You can get electronic probes that measure the stock automatically so you don’t need precision blanks. The probe loads in the tool changer so it can be completely automated. Automatic tool setting makes it so operators don’t need to measure new tooling in tool holders, and tooling wear can be monitored automatically.

I dabble in running a small machine-shop, and we are able to automate a good chunk of what people still do manually. The stock we use is cheap, straight from the mill stuff as we have the machine measure the stock with an electronic probe. The machines also have 20 pallets, so once the stock is loaded, the operator can leave the machine for 20x the cycle time of a part. The pallets don’t even have to be the same product, so we can queue up replacement of inventory with just the quantity that a customer ordered and offer a bunch of made-to-order parts with reasonable turnaround times.

The machines also monitor spindle vibration so they can tell if a tool looses an insert, and the tool-setter is used to check if solid tooling is still intact.

The only manual parts are taking raw materials off the suppliers truck, unloading finished parts (next on automation list), final assembly (working on automation for this), occasionally loading new tools as they wear/break and fulfillment.

Re:We are starting to operate our CNC machines remotely by Animats on Friday February 19, 2021 @01:47PM (#26196442)
The machines also monitor spindle vibration so they can tell if a tool looses an insert, and the tool-setter is used to check if solid tooling is still intact.

That's a key feature. For unattended operation, you must have good fault detection. This tends to be an overpriced extra cost option on machine tools.

There are a lot of things in industrial automation that cost more than they should. Motors with encoders, for example.

Re:We are starting to operate our CNC machines remotely by bsder on Friday February 19, 2021 @07:11PM (#26199821)
> There are a lot of things in industrial automation that cost more than they should. Motors with encoders, for example.

Not really. Motors with encoders aren't really much different in price from the alternatives at industrial sizes.

What you do see is that the transition from hobbyist machines to production machines is quite a significant price change. The jump from, say, a Tormach to a Haas is almost x10 (about $10,000 to $100,000).

This is not a surprise. Those machines are expected to run 24/7 and, if they don't, people are going to get angry and reputations come into play.

This space is optimized for production and if you're not, you're the outlier. Pre-Covid I accidentally tripped a Sunday delivery at the office from one of the machine tool suppliers--scared the hell out of me when someone knocked on my office door at 3:00PM on a Sunday. The delivery guy was just as confused--he had never delivered to such a nice office area. We both had a good chuckle about it all.

(Side anecdote: I had a really nice conversation with the late founder of Tormach many moons ago at a LittleMachineShop open house about servomotors vs steppers. He was quite blunt--the issue wasn't motor cost but customer service cost. His customer service budget would need to go up about $300K per year for about 3 years every time he introduced or changed some major machine feature. So, any change needed to earn $1M over 3 years and then be net positive after that in order to get implemented. Servomotors wouldn't pass that threshold--so unless a competitor forced him to, that upgrade wasn't happening.)

Re:We are starting to operate our CNC machines remotely by extrapickles on Friday February 19, 2021 @06:19PM (#26199384)
Most things I’ve found to be reasonably priced for what they are.

Most products are made with much higher quality materials than you would find in consumer gear. Also the “rated” spec for parts is expected to be understated as the “unreliable” part is one that fails in under 7-10 years of being run at the absolute limit of its spec. If a part fails in 2 years I will completely stop using that vendors products, as having a machine that is worth $1k/hr going down for even a day or two wipes out any savings.

Another factor is the total sales volume of automation products is low, so the engineering costs dominate pretty much everything in that space, even though everything is somewhat optimized to reduce engineering time (the buyers and/or vendors).

Re:We are starting to operate our CNC machines remotely by ska on Friday February 19, 2021 @04:50PM (#26198464)
I don't think actuators are crazy overpriced really. It's true that if you are going to bother packaging them you are probably using decent-to-good quality everything, but that's what you want for non-toy projects anyway. And for toy projects if your budget is really tight no big deal to set up the encoder yourself on this one-off.
Re:We are starting to operate our CNC machines remotely by dwohnitmok on Friday February 19, 2021 @12:57PM (#26195839)
Wow! That really does sound closer to what I thought CNC meant before I stepped into a machine shop.

That's pretty amazing stuff.

Re:We are starting to operate our CNC machines remotely by PragmaticPulp on Friday February 19, 2021 @01:55PM (#26196542)
This rabbit hole goes as deep as your budget allows.

If you're curious, search for Renishaw probes on youtube. They make some of the best mainstream tooling in this space.

Re:We are starting to operate our CNC machines remotely by singularity2001 on Friday February 19, 2021 @02:38PM (#26197106)
To turn on the probe, type G65 P9832. The CNC software world needs serious disruption / dev UI updates.
Re:We are starting to operate our CNC machines remotely by riskneutral on Friday February 19, 2021 @02:35PM (#26197069)
Is this a profitable business?
Re:We are starting to operate our CNC machines remotely by extrapickles on Friday February 19, 2021 @05:53PM (#26199104)
If you are careful yes. Doing job shop work (making other peoples parts) is hard to make a good profit as people expect overseas dumping rates.

The real profit comes from making your own products, as then you can force competition to also build their own factory to compete. By having lean production we can have a very large part catalog without having large amounts of inventory for low sales velocity parts.

We have at least a hundred variants that may only sell a dozen or two $100 parts per year, but they only cost us a line in the catalog to maintain the SKU. Since the products are for industrial use, most of our customers like the fact that we have in some cases been making the exact same part for nearly 30 years, which encourages them to design our products into theirs as we never discontinue products, so they don’t have to re-engineer theirs (our products in turn get used in machinery that might have a 10-100 unit/year global market).

Re:We are starting to operate our CNC machines remotely by valdiorn on Saturday February 20, 2021 @06:45AM (#26203448)
You've got me super curious. What sort of industries are you catering for when making your own products?
Re:We are starting to operate our CNC machines remotely by throwaway0a5e on Friday February 19, 2021 @07:01PM (#26199721)
Profitable? Yes.

Easy money? No

Fat margins? Hahahahahaha

(I.e. it's like most industries)

Re:We are starting to operate our CNC machines remotely by analog31 on Friday February 19, 2021 @05:34PM (#26198913)
As I understand it, the economics of machine shops are a bit weird because of the financing cost of keeping up with the latest equipment. If you have old machines, and not money to buy new machines, then you run old machines.

The most modern shops are in extremely high demand, expensive, always busy, happy to turn down work. If you can design something in a way that lends itself to conventional techniques, you can get it into a smaller shop that may have some idle capacity, or run on the "tool room" machines in the big shop. The big shops always keep a few old machines around for tooling and jig work, rework, and one-offs.

The smaller shops are also willing to take work that's not 100% detailed, even hand drawings. So you don't necessarily even need a CAD operator. "Do things that don't scale."

In kind of an odd analogy, my old high school band mate built a recording studio from cast-off obsolete equipment that he bought for pennies on the dollar, and it meant that he couldn't take the biggest jobs, but he was instantly profitable and never in debt. Likewise, I have a very small side business that involves some basic metalworking, and I do all of it with powered hand tools and jigs that I made from plywood and carbide drill bushings. My capital cost was under 100 bucks.

Re:We are starting to operate our CNC machines remotely by PragmaticPulp on Friday February 19, 2021 @01:47PM (#26196438)
> I had always had in my mind that with CNC machines you just stick the metal in the vise, load the program, hit start, and you're good to go, but there's manual calibration, facing off and the like that needs to be done before every run.

Much of it depends on the volume.

If you're building a million of something, the up-front cost to automate every step of the way makes sense.

If you're only building 10 of something once every few months, paying someone to do the manual operations 10 times makes more sense than investing in all of the fixturing, programming, and other tasks.

Really though, a lot of smaller machine shops have older CNC machines that are paid for and otherwise sitting idle. Hiring someone for $60/hr to do all the manual steps can keep that machine profitable.

Re:We are starting to operate our CNC machines remotely by megraf on Friday February 19, 2021 @11:40AM (#26194902)
It's all about the tools the shop has. Sapphire probes (edge finders) aid in a lot of the process. Mastercam allows you to simulate the machine process (and you can usually simulate it completely). Every shop is different – the shop I'm at here has a few lathes, robo-drills, 5th axis, and a few older pieces of hardware (which still are able to receive G-Code).
Re:We are starting to operate our CNC machines remotely by dwohnitmok on Friday February 19, 2021 @12:00PM (#26195131)
I was definitely using edge finders (it seems like machining in general would be way way way more work without edge finders) and occasionally Mastercam.

Definitely never used a 5-axis mill or robodrill though.

I guess my main point of comparison was to laser cutters, which really were basically push button automatable in comparison.

Granted the problem is a lot easier (purely 2-D cuts) and the cutter loses a lot of precision for thick material, but any time I got to use a laser cutter I was blown away by easy everything is and kept wondering whether a similar process could ultimately take root for machining.

Re:We are starting to operate our CNC machines remotely by jononor on Friday February 19, 2021 @01:19PM (#26196115)
The forces involved in CNC machining is a large complicating factor, compared to laser (or 3d-printing). In a laser one can just throw the material onto the bed, and the results will be fine - not so on a CNC. And that one is quite inherent to the paradigm.

Other aspects could likely be simplified and automated to a larger degree than today. In many areas solutions exists, but are quite high budget - things like tool changers, material loading and unloading.

Re:We are starting to operate our CNC machines remotely by phkahler on Friday February 19, 2021 @12:22PM (#26195383)
Machining can be simpler if you've got a couple precision features that can be clamped to with hard fixturing. It's all about positioning the workpiece accurately so the fixed g-code program can do its thing.
Re:We are starting to operate our CNC machines remotely by aj7 on Friday February 19, 2021 @01:51PM (#26196493)
That was before “good” machine shops had probes in every machine.
Re:We are starting to operate our CNC machines remotely by dogma1138 on Friday February 19, 2021 @12:18PM (#26195337)
You also need bodies to listen to the tool... ever since I build my small CNC machine I’ve learned just how important it is to listen to the cutting especially when you are doing adaptive passes to make sure your software doesn’t cock up the cuts.

This is probably the biggest area where i can see machine learning be actually useful with acoustic sensors.

I’m not an experienced machinist by any stretch of the imagination but even with my relatively small experience I can tell how good or bad the finish of a cut is going to be based on the sound the machine makes.

Re:We are starting to operate our CNC machines remotely by iancmceachern on Friday February 19, 2021 @01:07PM (#26195966)
Re:We are starting to operate our CNC machines remotely by dogma1138 on Friday February 19, 2021 @01:23PM (#26196159)
I would assume it does especially on 6-7 figure machines but I think even with basic microphones this might be a good application for ML at the small shop and hobbyist levels and I haven’t seen that yet.
Re:We are starting to operate our CNC machines remotely by jononor on Saturday February 20, 2021 @03:04AM (#26202476)
Anyone know of reasonably priced acoustic emission sensors? Even on AliExpress I could only find transducers that start around 500 USD. Would love something closer to 50...
Re:We are starting to operate our CNC machines remotely by iancmceachern on Saturday February 20, 2021 @04:21PM (#26208106)
I'm not sure these are "reasonably priced" but these have been my favorite product in this are: https://endaq.com/collections/endaq-shock-recorders-vibratio...
Re:We are starting to operate our CNC machines remotely by hef19898 on Friday February 19, 2021 @12:27PM (#26195451)
My first CNC experience was with a (C)NC machine from the 70s. I loved it at times. It was really amazing to see the machine shops being upgraded. The elvel of automation, already back in 201/12 (last time I had any close contact with these things) is amazing.

The concept of "Hauptzeitparllele Tätigkeit" (stuff operators can do when the machine is doing its thing, one of the things German just describes so well) stuck with me ever since.

Re:We are starting to operate our CNC machines remotely by polishdude20 on Friday February 19, 2021 @01:11PM (#26196018)
The other day, I realized our Haas CNC machine actually had a programmable coolant nozzle. You can program the nozzle to spray coolant at various locations!
Re:We are starting to operate our CNC machines remotely by myself248 on Friday February 19, 2021 @03:53PM (#26197907)
Yup, it's fun to make a "wash the part off" program that drives the table back and forth a few times with the nozzle at progressive angles. Or aim right at the perimeter of a big face mill.
Re:We are starting to operate our CNC machines remotely by Quequau on Friday February 19, 2021 @11:29AM (#26194791)
Moonlighting at a machine shop is something that I am very interested in doing. How did you wind up with such a position?
Re:We are starting to operate our CNC machines remotely by Ccecil on Friday February 19, 2021 @12:42PM (#26195662)
Depends on where you live. I recommend just going around and meeting machinists. Look into local meetings...Society of Manufacturing and such. Typically there are things like shop tours put on monthly (non-pandemic times). Talk to local machine shop instructors and/or metal suppliers and see who might be interested in hiring...they usually know everyone.

My area has many very, very large machine shops but it has a larger number of small "mom and pop" shops which just run a few machines. I have found that the people who run either type are equally as approachable...it is hit and miss if they are willing to even let you in the shop at all without NDAs and such...then there are others who have no issues with it.

Most of the really difficult to learn stuff in the field is fixturing and CAM setup. Once that is layed out it is mostly just changing parts and watching the machine run...but there is a lot to be learned while that is going on.

Re:We are starting to operate our CNC machines remotely by HeyLaughingBoy on Friday February 19, 2021 @05:53PM (#26199110)
I've never moonlighted, but I agree about the approachability.

Some time ago I lived in an industrial city with lots of small machine shops and especially lots of Screw Machine shops. I found that they really appreciated that I was interested in what they did and were willing to show me around.

Fast forward to about a year or two ago and I had to call on a prospective customer with a sales person. I didn't know until I got there that they were a branch of a well known workholding manufacturer and our contact offered to give me a tour of their machine shop. Pure heaven: I've never seen such a collection of modern, massive machine tools. The toolchanger alone on one of these machines was bigger than most VMC's I had ever seen. Their pallets were multiple feet long (not even sure if you call them pallets at that point) and ran on external tracks from machine to machine. Easily the biggest lights-out shop I've ever seen.

That was by far the most fun part of the sales call :-)

Re:We are starting to operate our CNC machines remotely by Quequau on Friday February 19, 2021 @01:05PM (#26195934)
Thanks for the reply. When / if the pandemic ends I have to move and I am seriously considering taking a few machining courses at a community college and changing careers.
Re:We are starting to operate our CNC machines remotely by megraf on Friday February 19, 2021 @08:18PM (#26200401)
At the start of COVID, I walked in, and told them I was interested. Coincidently, they needed some networking help. We ended up trading some skills, and then I just kept coming in. I didn't take no for an answer, and they liked it. YMMV.
Re:We are starting to operate our CNC machines remotely by paddy_m on Friday February 19, 2021 @11:59AM (#26195118)
I wrote an email to friends years ago about a side job I got at a machine shop while working in tech, it was quite well received. email in my profile, contact me and I'll send it to you.
Re:We are starting to operate our CNC machines remotely by blackrock on Friday February 19, 2021 @04:31PM (#26198274)
Maybe someone can build a robot to service and clean the machines?