News for hackers. Stuff that matters.
Re:Print this file, your printer will jam (2008) by Denzel on Saturday December 26, 2020 @11:55AM (#25544594)
This is not a bug.

I also drive a Model 3, spiritedly. Of course, I’ve rotated my tires many times, on schedule, but I replace them all at the same time. It’s standard practice. I’ve never experienced OPs behavior.

The algorithm is such that there’s a limit to the amount of “slippage” it will accept before traction control engages. A difference in tire diameters, exacerbated by a hard curve, leads to more slippage than the algorithm is willing to accept. What do you think would happen if traction control was off? :)

Furthermore, there are unknowns here - OP hasn’t specified the diameter (between 2 and 8/32’s) of their old tires. They simply stated that the tires had enough tread to meet their personal standards. Clearly traction control sees the situation differently.

Re:Print this file, your printer will jam (2008) by jacquesm on Saturday December 26, 2020 @12:03PM (#25544664)
Definitely a bug. If tires are within spec the traction control should not trigger, it should trigger when a wheel slips, not when it is in fact having good traction.
Re:Print this file, your printer will jam (2008) by AndrewBissell on Saturday December 26, 2020 @12:46PM (#25544984)
A bug? In a Tesla? Naaaaaaah ...
Re:Print this file, your printer will jam (2008) by speedgoose on Saturday December 26, 2020 @01:59PM (#25545521)
It's fine, they will update your car remotely and remove the bug. Eventually. By the end of a year.

Still want one though.

Re:Print this file, your printer will jam (2008) by wkearney99 on Sunday December 27, 2020 @02:31AM (#25549505)
tried driving a Taycan yet?
Re:Print this file, your printer will jam (2008) by speedgoose on Sunday December 27, 2020 @03:32AM (#25549713)
No, there is no Porsche Taycan to rent in my area. It seems to be a very nice car.
Re:Print this file, your printer will jam (2008) by foolmeonce on Saturday December 26, 2020 @12:56PM (#25545062)
Why would AI or fuzzy logic need to be provided with perfect sensors when human drivers are not? If you break 101 times out of 100, whoever rear ends you is at fault, 99 out of 100, OTOH..
Re:Print this file, your printer will jam (2008) by jacquesm on Saturday December 26, 2020 @01:02PM (#25545110)
Because traction control is a safety system and if it kicks in when you don't expect it it can turn a safe system into an unsafe one.
Re:Print this file, your printer will jam (2008) by zeusk on Saturday December 26, 2020 @01:11PM (#25545177)
I guess people already forgot what caused 737 MAX
Re:Print this file, your printer will jam (2008) by wkearney99 on Sunday December 27, 2020 @02:29AM (#25549498)
Had an '05 Jeep Grand Cherokee that LOVED to kick in traction control right at the critical moment of trying to make an abrupt U-turn. Like pedal down, lurch.... ummmm, think... ok, here's SOME throttle... while there's a SEMI barreling toward you... Ya learned NOT to try u-turns that might require haste.
Re:Print this file, your printer will jam (2008) by jacquesm on Sunday December 27, 2020 @02:49AM (#25549570)
Oh that seriously sucks.
Re:Print this file, your printer will jam (2008) by o-__-o on Sunday December 27, 2020 @10:15AM (#25551563)
My TC does the same thing. All cars after 2008 will cut throttle and apply brakes if losing traction. Turning off traction control disables this system until you press the brakes which then enables passive traction control (the car will not actively brake but will cut power)

Thank Ford+Bridgestone for this

Re:Print this file, your printer will jam (2008) by foolmeonce on Saturday December 26, 2020 @01:34PM (#25545351)
Yes and a good driver can get you killed from good reaction time. Driving is a game of russian roulette that involves a lot of intelligences with poor senses doing random things.
Re:Print this file, your printer will jam (2008) by jacquesm on Sunday December 27, 2020 @02:51AM (#25549577)
Yes, but you don't add extra complications to see if the drivers reaction time is 'good enough' or not, especially not since (1) this is a solved problem and (2) it is supposed to make you safer, not less safe. Tesla should simply fix this.
Re:Print this file, your printer will jam (2008) by o-__-o on Sunday December 27, 2020 @10:14AM (#25551555)
Then maybe follow your manufacturers maintenance guidance and stop assuming all cars are made the same?
Re:Print this file, your printer will jam (2008) by BoorishBears on Saturday December 26, 2020 @02:50PM (#25545924)
This is table stakes for TC which companies like Bosch solved and commoditized. I don't know why you're defending it.
Re:Print this file, your printer will jam (2008) by dzhiurgis on Saturday December 26, 2020 @06:24PM (#25547293)
Sounds like fail-safe design. It decelerates instead of spinning out of control. You’re overreacting a bit.
Re:Print this file, your printer will jam (2008) by jacquesm on Sunday December 27, 2020 @01:48AM (#25549360)
Traction control can selectively apply the brake to the wheel that it thinks is spinning too fast. If the wheel isn't spinning too fast that that can throw the vehicle into a skid (the reason traction control exists is to avoid going in to a skid).

So it's not just decelerating the vehicle, it's decelerating the wheel that it thinks is rotating too fast to make it match the speed of the road. When in a curve as described by the OP if the wheel is a front & driven wheel this could cause severe understeer causing the car to move further out, which will in turn cause the inboard wheels to slow down further relative to the outboard ones. This could cause a positive feedback loop. Note that if you start braking one wheel that's on a diff the other wheel will attempt to speed up.

Re:Print this file, your printer will jam (2008) by t0mas88 on Saturday December 26, 2020 @03:12PM (#25546112)
It may be "within spec" for a Tesla, but other brands with traction control don't have this problem. And that is a typical issue with Tesla, they have too many software guys and too little real world automotive experience. So they'll create these kinds of problems by implementing their own things instead of going with proven existing tech.

The most rampant example was the rain sensor on the early model S. They decided not to buy the same perfectly working sensor that any German car had for 10+ years at the time, no they decided to implement the rain sensor by training some image recognition on the camera that's behind the windscreen. Worst idea ever, because it meant the 100k+ euro Model S had no automatic wipers for a long time and when they got there it was worse at detecting rain than the standard sensor on a 20k euro VW Golf...

Re:Print this file, your printer will jam (2008) by jonahrd on Saturday December 26, 2020 @05:48PM (#25547051)
To specify further: this is a problem in Teslas with autopilot 2.0+ hardware, where they switched from 1 front facing camera to 3. That left no room for the Bosch rain/light/humidity sensor, so they put developed their own light/humidity sensor, but still didn't have enough room for rain sensing hardware. The solution was left up to the autopilot team since it was assumed (wrongly) that sensing rain using a camera was easier than using specific optical sensors designed for the task.

Source: I worked on the replacement TH sensor.

Re:Print this file, your printer will jam (2008) by londons_explore on Saturday December 26, 2020 @07:30PM (#25547665)
It is an odd design decision, since I assume a rain sensor at its core is simply an LED and a light sensor carefully arranged. Total cost of the core components: $0.03. Neither need to be physically large either.

It's even more odd considering the cameras can totally also be used as light sensors (simply read back the exposure time for example). Why get rid of one unnecessary sensor without getting rid of another?

I wonder if perhaps it was done to force the vision teams to become less science/research oriented and more 'we need this result now, we have angry customers waiting' based.

Re:Print this file, your printer will jam (2008) by 11thEarlOfMar on Saturday December 26, 2020 @03:48PM (#25546343)
Mine thinks that a chip in the windshield is a raindrop. I had to turn off automatic wipers.
Re:Print this file, your printer will jam (2008) by m463 on Saturday December 26, 2020 @03:29PM (#25546225)
I believe tesla will recalibrate all this after you drive for a certain distance.

Thing is - they would get complaints because the system would disable certain functions with a message during recalibration.

I wonder if they have now turned the dial too far the other way.

Re:Print this file, your printer will jam (2008) by Dylan16807 on Saturday December 26, 2020 @04:41PM (#25546658)
If they can't recalibrate in the background, that's an entirely different problem. It's not a matter of turning a dial, it's fixing a flaw.
Re:Print this file, your printer will jam (2008) by Dylan16807 on Saturday December 26, 2020 @04:38PM (#25546637)
This is a bug.

The slippage calculation should take tire size into account. Anything else gives you wrong numbers.

Re:Print this file, your printer will jam (2008) by moonbug on Saturday December 26, 2020 @01:56PM (#25545504)
uhoh. you're going to rattle the Tesla fanbois.