News for hackers. Stuff that matters.
Re:Boeing MAX production cut signals long grounding by panarky on Sunday April 07, 2019 @01:51PM (#19598519)
Not only a longer grounding, but some airlines are canceling orders and many passengers don't want to fly in them.

The 737 Max could become the Edsel of airplanes.

https://en.wikipedia.org/wiki/Edsel

Re:Boeing MAX production cut signals long grounding by adrr on Sunday April 07, 2019 @02:12PM (#19598699)
I won’t fly one unless it has 3 angle of attack sensors. Since that can’t be easily found out, I’ll avoid them.
Re:Boeing MAX production cut signals long grounding by noncoml on Sunday April 07, 2019 @03:08PM (#19599168)
The problem is not the missing extra angle of attack sensor, but incompetence at every step.

If I understood correctly, MCAS trimmed it so much that the pilots were unable to bring it back manually.

This sounds like Boeing engineers didn’t even put a limit on the maximum trimming that MCAS can do, not even to the maximum theoretical limit for the plane/engines.

Re:Boeing MAX production cut signals long grounding by HarryHirsch on Sunday April 07, 2019 @05:24PM (#19599981)
MCAS trimmed it so much that the pilots were unable to bring it back manually.

Not only that, MCAS controlled an electric motor which turned the trim wheel and which could apply more torque than a human turning it manually. The only way to disable MCAS was to cut power to that motor. MCAS pointed the aircraft at the ground, and it was impossible to trim the aircraft to achieve level flight again.

Mind, MCAS was supposed to be a crutch to fly at the edges of the flight envelope, something that a regular pilot would never encounter because under normal conditions pilots wouldn't find themselves in a regime where MCAS would be activated. That was the idea, instead we had two hull losses within 6 months!

Re:Boeing MAX production cut signals long grounding by Obi_Juan_Kenobi on Sunday April 07, 2019 @06:20PM (#19600319)
The electric trim adjustment is obviously going to be more powerful, that's just the reality of large planes. That's not the issue.

The issue from the Ethiopian crash was that, in the extreme trim angle, there was simply too much force on the screw to turn manually. This condition is trained for, and the solution is to let the plan angle down to relieve the aerodynamic pressure on the control surface. That gives you an opportunity to manually control the trim wheels.

The pilots did not have the benefit of altitude to perform this maneuver, so (likely) instead re-enabled the electric trim in a bid to use it to reduce the nose-down trim before the MCAS would re-engage. This proved fatal.

Re:Boeing MAX production cut signals long grounding by matt-attack on Monday April 08, 2019 @12:30AM (#19602099)
Are you suggesting with the auto-trim disabled, the two pilots working together, with those handles extended on the trim wheel, were not strong enough to crank the trim wheel?
Re:Boeing MAX production cut signals long grounding by cmurf on Monday April 08, 2019 @01:33AM (#19602406)
Yes. Known issue.

Scroll down slightly for the empennage diagram, right hand side, item 3.

https://www.seattletimes.com/business/boeing-aerospace/boein...

Re:Boeing MAX production cut signals long grounding by dreamcompiler on Sunday April 07, 2019 @06:53PM (#19600472)
It's very easy to see the two AOA sensors on a Boeing jet when it's parked at the gate--there's one on each side of the plane. What I don't know is where Airbus puts the third one.
Re:Boeing MAX production cut signals long grounding by Zak on Sunday April 07, 2019 @07:18PM (#19600596)
Airbus puts two on one side and one on the other.
Re:Boeing MAX production cut signals long grounding by mrpippy on Sunday April 07, 2019 @02:55PM (#19599075)
No 737 has 3 AoA vanes, and it’s extremely unlikely they’ll ever change the design to accommodate that. Every MAX will have an indicator to show if they disagree though.
Re:Boeing MAX production cut signals long grounding by fanf2 on Sunday April 07, 2019 @07:45PM (#19600732)
The AOA disagree indicator was an optional extra that was missing on the planes that crashed - https://arstechnica.com/information-technology/2019/04/boein...
Re:Boeing MAX production cut signals long grounding by mrpippy on Monday April 08, 2019 @01:31AM (#19602401)
Correct, and the AoA disagree indicator will be added to every plane (for free) as part of the MCAS software fix.
Re:Boeing MAX production cut signals long grounding by anoncake on Sunday April 07, 2019 @05:26PM (#19599994)
Does adding a sensor really significantly change the design?
Re:Boeing MAX production cut signals long grounding by darkpuma on Sunday April 07, 2019 @02:26PM (#19598813)
Three angle of attack sensors seems unnecessary to me. They simply need to make MCAS pay attention to both (2) and cut out if one disagrees with the other.
Re:Boeing MAX production cut signals long grounding by jarym on Sunday April 07, 2019 @02:31PM (#19598857)
The reason there should be 3 is likely because the odds of 2 failing are not unlikely enough from a safety perspective.

There’s no problem if one fails but what if both fail and both corroborate a bad reading?

Certainly the cost of 3 such sensors would not be as high as the cost of another crash.

Re:Boeing MAX production cut signals long grounding by maxmunzel on Sunday April 07, 2019 @02:55PM (#19599071)
As far as i know you use three sensors, so you can automatically compensate for one failing/misreporting sensor without human intervention.
Re:Boeing MAX production cut signals long grounding by darkpuma on Sunday April 07, 2019 @02:59PM (#19599100)
You can't compensate because you don't know which one is wrong. However you can make MCAS inactive whenever the two sensors are disagreeing with each other.
Re:Boeing MAX production cut signals long grounding by Macha on Sunday April 07, 2019 @03:56PM (#19599432)
With the current two sensor setup, that is true.

This is why the parent poster is arguing for 3 sensors (and the real reason for tripling). If not all sensors agree but 2/3 do, it is more probable that the two sensors are correct than the 1 sensor disagreeing.

Re:Boeing MAX production cut signals long grounding by darkpuma on Sunday April 07, 2019 @05:37PM (#19600062)
Right, but the MCAS system as it was implemented during those two crashes did not disable itself when the two sensors disagreed. It could have, but didn't. Boeing is apparently changing that, and I believe that change to be sufficient.

MCAS being automatically disabled when the sensors agree but leaving the pilots with electronic trim control seems like a perfectly adequate solution. The MCAS system was never even necessary for flight, it was only necessary for certification. In the situations where it's meant to be active, which are a limited subset of all high angle of attack scenarios, it's fine system to have if it's working correctly. But it should never be active outside of that limited set of scenarios. It should never be active when both angle of attack sensors aren't indicating a high angle of attack within a reasonable distance of each other.

Frankly, if two sensors are indicating a high angle of attack and one is not, it's probably still sensible to disable MCAS. I don't have any of the real numbers, but the chance of a 737 being in a low speed high angle of attack scenario is low in the first place, possibly sufficiently low that "two sensors being wrong and the aircraft being in level flight" might be more likely than "aircraft is near stall and one sensor is wrong."

To know for sure we'd need at least the hard data on what modes of failure these sensors have, how likely any of those modes is to occur and what the expected readouts from those failure modes are, and how likely a 737 is to encounter a low speed stall scenario. We, or at least I, don't have any of that. But my gut says that two sensors are sufficient iff the MCAS system is only active when they agree.

Furthermore, the chance of two sensors being wrong actually goes up if you have three sensors, rather than two. Correct me if I'm wrong, stats was never my strong point, but it seems to me like the cumulative binomial distribution is relevant here:

    #lang racket
    (require math/number-theory)

    (define (general-binomial p k n)
      (* (binomial n k)
         (expt p k)
         (expt (- 1 p)
               (- n k))))
    
    (define (cumulative-general-binomial p k1 k2 n)
      (apply +
             (map 
               (λ (k) (general-binomial p k n))
               (range k1 (add1 k2)))))
    
Chance of a single sensor failing, if each has a 1% chance of failure (sanity check):

    > (cumulative-general-binomial .01 1 1 1)
    0.01
Chance of two or three out of three sensors failing, if each has a 1% chance of failure:

    > (cumulative-general-binomial .01 2 3 3)
    0.00029800000000000003
Chance of two out of two sensors failing, if each has a 15 chance of failure:

    > (cumulative-general-binomial .01 2 2 2)
    0.0001
Two out of three sensors failing is three times more likely than two out of two sensors failing!

(In other words, two broken sensors voting out a third working sensor is more likely than two out of two sensors being broken.)

Re:Boeing MAX production cut signals long grounding by jarym on Sunday April 07, 2019 @05:51PM (#19600148)
I think your maths is sound but the question is what are the odds that multiple sensors fail on the same flight (and I don't know the answer)?

Because as soon as one sensor fails that aircraft will go in for maintenance.

Re:Boeing MAX production cut signals long grounding by darkpuma on Sunday April 07, 2019 @06:06PM (#19600237)
That was kind of my point..

MCAS should turn off as soon as a single sensor fails, and three sensors are therefore unnecessary. Two sensors are sufficient to detect when a single sensor fails. If you only have two sensors and two fail, then MCAS remains active and your plane crashes. But that's not likely to happen. However that's more likely to happen if you have three sensors and try to use two sensors to vote out a third, in order to keep MCAS active when a sensor fails. In that configuration, a double failure (causing a crash) is three times more likely.

My conclusion is turn off MCAS as soon as even one sensor disagrees with the others. And if that's how MCAS is configured, then three sensors is unnecessary overkill. If you want overkill, you may as well double up the sensors on both sides and have four instead of three; all the better right?

Re:Boeing MAX production cut signals long grounding by tropo on Sunday April 07, 2019 @08:29PM (#19600941)
A good rule would be to keep MCAS active, choosing to use the sensor that produces the less-extreme adjustment.
Re:Boeing MAX production cut signals long grounding by darkpuma on Monday April 08, 2019 @12:08AM (#19601982)
Eh, that kind of makes a certain amount of sense, but I don't think that's quite right. Determining which of the two sensors is less-extreme supposes knowledge about the airframe's current state. If he aircraft is currently in a very high angle of attack low speed stall, then the sensor that says everything is A-Okay is the extreme sensor.

I understand that's not what you mean, that the sensor indicating a situation closes to nominal flight should be chosen, but I think the sticky part is that MCAS isn't a system meant for normal flight conditions. MCAS is only supposed to be active when the aircraft is in an extreme scenario. So in fact if the sensor with "less-extreme adjustment" is preferred, in a way that actually means the system functions as I suggested: MCAS is disabled if the sensors disagree. But not quite. In your scheme if both the sensors are extreme but disagree, MCAS would be active to the lesser extent. But in my scheme, if both sensors are extreme but disagree, MCAS would be totally inactive (while leaving the pilot with electronic stabilizer trim control of course, allowing the pilot to manually do anything MCAS would be capable of doing.)

Re:Boeing MAX production cut signals long grounding by leesalminen on Sunday April 07, 2019 @02:29PM (#19598844)
How would it know which one is the malfunctioning one?
Re:Boeing MAX production cut signals long grounding by janc_ on Sunday April 07, 2019 @02:50PM (#19599017)
That's not important; you disable that “autopilot feature” and sound an alarm in the cockpit explaining what the exact error is. Should be enough for the human pilots to react properly.
Re:Boeing MAX production cut signals long grounding by darkpuma on Sunday April 07, 2019 @02:57PM (#19599085)
You don't.... That's why I said "and cut out if one disagrees with the other."

If they don't both give the same reading, MCAS turns off.

Re:Boeing MAX production cut signals long grounding by rootusrootus on Sunday April 07, 2019 @02:05PM (#19598635)
History suggests that people will forget this very quickly. I wouldn't be surprised to see Boeing 'rebrand' the plane as 737-8, but it probably won't be necessary.
Re:Boeing MAX production cut signals long grounding by rwc on Sunday April 07, 2019 @02:42PM (#19598958)
Re:Boeing MAX production cut signals long grounding by rootusrootus on Sunday April 07, 2019 @02:50PM (#19599024)
The 737-800 is a 737NG. The model number for a 737 MAX-8 is 737-8. That's why I put rebranding in quotes -- it's already the official designation for the plane. I could see them dropping the public "MAX" branding from what they print on the side of the plane and just calling it 737-8 (and -7, and -9, for the other models) everywhere.
Re:Boeing MAX production cut signals long grounding by vlehto on Sunday April 07, 2019 @02:45PM (#19598987)
From aviation it could be the De Havilland Comet. But that brought the whole company down. So let's hope this will not go there. Airbus having a monopoly is no ones interest.
Re:Boeing MAX production cut signals long grounding by mcv on Monday April 08, 2019 @07:32AM (#19604183)
I'm honestly surprised they're not cutting back production more than this. If I was an airline that thought long and hard about whether to order the 737 Max or the Airbus A320neo, and ultimately decided on the Boeing, these events, and the likelihood of recertification and further training requirements for pilots might well make me reconsider that decision.

If Boeing really needed to cut these corners in order to remain competitive, then having to redo those corners might make them too expensive or inefficient for the market.

Re:Boeing MAX production cut signals long grounding by sseveran on Sunday April 07, 2019 @04:14PM (#19599542)
That is unlikely. The A320neo family currently has an order backlog of over 6000. The only airline I know that is actually pursuing cancellation is Garuda. Given that the A320neo family is really the only competitor to the 737MAX family airlines don't really have anywhere else to go.

I also doubt customers will really vote with their feet given that the number one factor when booking a ticket is price. If some people choose not to fly on them it will create supply/demand imbalances in the market which would be interesting.

Re:Boeing MAX production cut signals long grounding by stingraycharles on Sunday April 07, 2019 @04:33PM (#19599662)
Why do these airplane manufacturers all have such massive order backlogs? Is it that difficult to scale production?
Re:Boeing MAX production cut signals long grounding by inferiorhuman on Sunday April 07, 2019 @04:51PM (#19599777)
Yes. Take a look at the issues Boeing had with the 787 production or even just the distance which both Airbus and Boeing ship giant pieces of airplane.
Re:Boeing MAX production cut signals long grounding by mikeash on Sunday April 07, 2019 @05:25PM (#19599992)
Airbus currently builds about 660 A320s per year. At roughly $100 million apiece, that’s about $66 billion per year of product. How many other manufacturing companies produce that much stuff? And this sort of low volume, high value manufacturing is a bad fit for the sort of automation that allows, say, Toyota to build 10 million cars per year.
Re:Boeing MAX production cut signals long grounding by FabHK on Sunday April 07, 2019 @05:09PM (#19599889)
> I also doubt customers will really vote with their feet

Agreed. As the article points out:

"Passengers eventually returned to flying the 787 and to other airplanes that were grounded: the McDonnell Douglas DC-10, the Douglas DC-6, the Lockheed Constellation and even the de Havilland Comet."

Re:Boeing MAX production cut signals long grounding by freehunter on Sunday April 07, 2019 @05:20PM (#19599950)
I'm not sure the DC-10 is a great example. It was grounded in 1979 and discontinued in 1983 after airlines stopped ordering it. The company never recovered and died a long and slow death until Boeing scooped them up.
Re:Boeing MAX production cut signals long grounding by HarryHirsch on Sunday April 07, 2019 @05:49PM (#19600132)
Neither is the Lockheed Electra (one would guess that the author means that airplane instead of the Constellation). Airlines cancelled their orders and Lockheed had to end production of the model early, leading to very substantial losses for the company.
Re:Boeing MAX production cut signals long grounding by rpiguy on Sunday April 07, 2019 @02:01PM (#19598608)
Unlikely as there are no readily available replacement planes for airlines who need to replace their fleet. Airbus can only produce so many, the supply chains and production facilities just aren’t there. Even if Airbus somehow magically increased their production by 50%, Boeing would still sell 2000+ 737 MAX planes (or the previous generation 737 models)