Bluetooth profiles, and vendors restricting their devices to sport only certain profiles, are a good thing for compatibility, since it ensures (if done correctly) that devices (i.e. applications in fact) from different vendors can talk to each other.
"WiFi direct" is yet another completely different thing, that is meant for peer-to-peer connections (note: two communication partners) without needing an AP, which 802.11 consumer standards (b,g,n,ac) all did and do otherwise.
Also this standard has nothing to to with flash-mob gaming, and won't allow for it. This is AFAIK meant as a standardization of several so far vendor-specific efforts to extend networks through the use of several APs (similarly to how repeaters were used). Still a good thing, because it is no longer vendor-specific if my devices support the standard.
By expecting mesh networking to solve your applications needs you are IMO skipping a few layers in between. You want ad-hoc, high throughput mesh networks, stateless auto-configuration, service discovery, and quite a few other things regarding routing, QoS and flow management as well as connection management (reliability, multicast?)...
This is not the standard you are looking for. For now you would need to look for solutions in the application layer IMO.
Wi-Fi Direct is nothing more than running (e.g., 802.11n) software AP with WPS on one device ("Group Owner") and having (multiple) peers connect to it to form a "group" -- it's just a normal AP, you can even connect legacy Wi-Fi devices to it. It does add functionality to automatically negotiate which device becomes the access point and to do some service discovery on the link layer before connecting.
The problem with WiFi Direct is that all its local mobile-to-mobile capabilities are disabled if the group doesn't have a node connected to a tower at all times. For example, you can't have three devices up in the mountains exchange files or messages, unless one of them can get the OK from a service provider's tower. WiFi Direct stops as soon as you lose cellular signal or experience a service timeout. It's crippled by design.
EasyMesh doesn't seem to offer any neighbor-to-neighbor utility; It appears to be focused solely on expanding coverage of single-point-of-control networks which are already overcrowded (hence the need for so many range extenders). When are we not in range of half a dozen or more WiFi networks?
I see adding more APs as an exercise in futility. The primary issue is overcrowding, not signal strength. Remove all the other nearby networks & one router easily reaches across most buildings.
Sorry, I guess that's two topics in one comment, but I'll repeat my primary question: In what way are these different approaches "completely" different? They seem to all be chasing roughly the same goal. I also feel that "mesh" has stagnated due to lack of hardware support (& accompanying lack of open source firmware).
I'M SORRY! I was thinking of LTE Direct, which is crippled by design. Please disregard my statement about "WiFi Direct" needing a cellular tower.
Nice try blaming it on political pressure, but I'd call it sound engineering! "Let's get the simple stuff right before we discuss the support costs of making mesh work over this junk"
Because each pairing is effectively a new device in /dev, and doing anything with bluetooth require that one cross the user/root divide multiple times.
Assuming audio between 2 peers at 1 meter was somehow a solved problem (per above it's not), and collision avoidance was a non-issue (problem worsens exponentially with additional peers), that's 1.16KB/sec in some idealized non-existent reality of bandwidth to run a compelling game for 62 people. Perhaps parent comment refers to a flash mob game of Chess.
Assuming Bluetooth only reliably fails between two peers 1% of the time (oh, but to dream), that's a 99%^62 = 5.36% chance of a bus full of people successfully joining a single mesh.
Silliness is in the eye of the beholder!
Out by an order of magnitude but your point still stands.
Note that the Nintendo 3DS effectively has this capability. I believe it's all WiFi-based.
This means that there are baked in standard ways for devices to communicate.
Damn it, back in the day i had a Nokia N800 going online via a SE featurephone, while listening to music via Jabra headphones from the same phone, and typing comments on various forums using a folding keyboard paired with the N800.
Some of these standards are decent technologically, but the real problem comes down to device drivers. Most wifi/bluetooth devices have drivers (and sometimes firmware, too) which are completely inflexible in sending out frames outside of their standard protocols. This is especially difficult with the abstraction layers programmed into the firmware and the fact that very different hardware is used to share spectrum (to optimize for time hopping on bluetooth, for example).
The solution: adoption of a standardized, Linux-like driver protocol for enabling custom frames to easily be sent and received on shared spectrum BEFORE adoption of the protocols built on top.
That being said, augmenting the Wifi standard to support mesh is probably the closest development to that goal that I've seen in a while, since vendors typically start supporting the new 802.11 standards pretty quickly.
Any use of the word “mesh” online invites commenters who, not having RTFA, will opine endlessly based on an incorrect understanding of a completely different use of “mesh”.
I constantly find myself using qualifiers like "hybrid mesh cellular" (doesn't exist due to hostile regulation), "link-layer optimization for mesh processing", & "app-layer mesh protocols for decentralized Directed Acyclic Graph consensus". "Mesh", "matrix", "net", & "web" are all terms which are virtually interchangeable in contexts outside the IT realm. "Star" most accurately describes the topology of most people's single-AP WiFi implementations, yet the term is deprecated due to association with a specific old protocol nobody's done much with in thirty years, as far as I know.
The whole thing is a linguistic nightmare, from anything but a marketing perspective (marketing loves conflation; it's one of the industry's primary tools).
EasyMesh protocol finalization looks like great news for installers & WiFi network admins, but I expect the new range extenders it enables to make the overcrowding situation worse, not better.
If it doesn't enable peer nodes to communicate without a centralized point of control, I'd vastly prefer the term "mesh" not be used at all.
Edit: I was thinking of more dynamic and larger meshes - those are really hard. This standard seems to have a smaller scope. It's still more difficult than one-to-one.
Bluetooth 1.0 in 2002 with support from the Palm Pilot, to give you a sense of how long ago that was technologically, already had this dream and implemented a Personal Area Network using 'scatternet'.
Probably the single largest blow to the dream of meshed devices everywhere, imho, was Apple's decision to limit the iPhone's (2007) bluetooth support to headset-only when bluetooth was capable of so much more. Admittedly there was probably substantial pressure from the carriers who were scared of the idea of phones communicating with out being mediated/dependent on cell tower infrasructure, but its one thing I cannot forgive apple for. The other phone vendors fell into line.
Android 4.0 (2011) implemented Wifi peer-to-peer, which the Wifi Alliance called "Wifi Direct" that would allow for Personal Area Networks using existing wifi hardware.
[1] https://developer.android.com/guide/topics/connectivity/wifi... [2] https://en.wikipedia.org/wiki/Wi-Fi_Direct
Now that bluetooth has returned to its roots with Bluetooth Low Energy, maybe we have another chance at flash-mob mobile gaming - everyone on the same bus can join in to a chatroom or a roleplaying game for the duration of the ride.