News for hackers. Stuff that matters.
Re:What does a kilowatt hour look like? by spdustin on Thursday September 22, 2016 @07:35PM (#12561231)
Given how popular (and damn near impossible to discern) unsafe and unprotected lithium-ion batteries are, the idea of making a homegrown power wall terrifies me in ways I can't even begin to contemplate.

An 18650 battery, if combusted, can produce hydrofluoric acid with just water vapor in the air (or the water in your lungs) if they use lithium hexafluorophosphate as the electrolyte. Hydrofluoric acid can and will cause permanent damage to lung tissue if inhaled, and nasty, nasty chemical burns to exposed skin. 18650 batteries are supposed to have several failsafes to prevent thermal runaway, but counterfeit batteries can lack those failsafes. Not to mention, in some laptop battery packs, the protection was pack-wide, and not in individual cells. Not knowing the chemistry of the cells or the state of the protection circuitry of the battery would make me very nervous. Maybe someone else can provide more detail on how to test them safely.

Re:What does a kilowatt hour look like? by jrockway on Thursday September 22, 2016 @09:29PM (#12561702)
You have to realize that 1kWh is a lot of energy. Imagine being hit (in a world without an atmosphere) by a 60 pound suitcase falling out of an airliner flying at 45,000 feet. Same amount of energy as that battery pack. (Alternatively: the most powerful air conditioner you can buy running full blast for 30 minutes. Incidentally, that battery pack has as much energy as 100mL of gasoline, which is why gasoline-powered cars are so popular.)

When you put a lot of energy in a small space and release at all at once, it's called a bomb. Li ion batteries are small bombs that can be used to power electrical devices.

Some chemistries are safer than others, like A123 cells. The market did not care about safety and they went bankrupt. Energy density is king.

Re:What does a kilowatt hour look like? by dghughes on Thursday September 22, 2016 @10:28PM (#12561917)
Even a single AAA battery has a lot of energy 5,071 J according to http://www.allaboutbatteries.com/Energy-tables.html.

My point of reference I use to imagine energy is a major league baseball player hits a baseball with 1,234 J.

1KW/h is 3,600,000 J.

Re:What does a kilowatt hour look like? by akiselev on Friday September 23, 2016 @12:49AM (#12562395)
In other words: 1 kWh is the equivalent of the average MLB player hitting a home run roughly every 1.2 seconds.
Re:What does a kilowatt hour look like? by jfoldager on Friday September 23, 2016 @04:07AM (#12563052)
.... For one hour. Your units do not check out. He just needs to hit the ball ~ 3000 times. Imagine that exploding in your face.
Re:What does a kilowatt hour look like? by novaleaf on Friday September 23, 2016 @09:05AM (#12564249)
love that visual the best ;)
Re:What does a kilowatt hour look like? by ralfd on Friday September 23, 2016 @06:41AM (#12563568)
Wow, 100 ml of gasoline could propel a suitcase into the stratosphere? That seems so counterintuitive.
Re:What does a kilowatt hour look like? by chrismcb on Friday September 23, 2016 @06:59AM (#12563628)
Only if there is no atmosphere.
Re:What does a kilowatt hour look like? by majewsky on Friday September 23, 2016 @07:12AM (#12563691)
> 60 pound suitcase falling out of an airliner flying at 45,000 feet. Same amount of energy as that battery pack

You did not account for the terminal velocity of the suitcase. It cannot accelerate indefinitely because of the air resistance.

If I assume that the suitcase will not break the sonic barrier (which seems reasonable), I get an upper bound on its kinetic energy of

  0.5 * 60 pounds * (1 mach)^2 = 0.41528548 kilowatt hours
according to units(1).
Re:What does a kilowatt hour look like? by jahnu on Friday September 23, 2016 @07:32AM (#12563776)
> (in a world without an atmosphere)
Re:What does a kilowatt hour look like? by walrus01 on Thursday September 22, 2016 @10:16PM (#12561874)
> (Alternatively: the most powerful air conditioner you can buy running full blast for 30 minutes.

I can easily buy a 16 ton (1 ton = 12000 BTU/h) air conditioner, it uses a great deal more than 1kWh in 30 minutes.

http://www.ebay.com/itm/Carrier-16TON-R-410A-Puron-Air-Condi...

Re:What does a kilowatt hour look like? by jrockway on Friday September 23, 2016 @01:57AM (#12562613)
I mean to say, "plug in to your 120V 18A circuit".
Re:What does a kilowatt hour look like? by StavrosK on Friday September 23, 2016 @09:37AM (#12564472)
I wonder why we have a tendency to nitpick rough estimates and go "YOU DIDN'T ACCOUNT FOR X EDGE CASE!", when even we get the gist.
Re:What does a kilowatt hour look like? by viewer5 on Friday September 23, 2016 @10:41AM (#12564955)
If I had to guess, it's someone who's like "I wonder how big that AC unit is" because the idea tickled their imagination, googles it, then finds that it doesn't quite match with the scenario given.
Re:What does a kilowatt hour look like? by asteli on Thursday September 22, 2016 @08:30PM (#12561479)
Building a pack from random cells like this is pretty much a cardinal sin with Li-Ion pack design. Cell resistance and state of health are carefully matched during pack manufacture to ensure cells charge and discharge evenly. Li-ion cells are pretty sensitive, so on top of that, large packs have battery management systems (BMS) to balance cell voltages and monitor for faults and damaged cells.

Attempting to charge a pack like shown has a very real risk of causing one or more of the cells to overcharge and breach, or worse, violently catch fire.

Re:What does a kilowatt hour look like? by rektide on Friday September 23, 2016 @03:16AM (#12562884)
Yeah, very much. Some basic dilligence with a somewhat even set of cells will probably be harmless. I would not be afraid of that kind of homebuilt power-store, if some decent practices are followed. (But you should do your dilligence & check to make sure all the cells remain ok, as you start using this pack!)

This... this is an hellish unbelievable nightmare, is asking for something to go wrong. It is certianly possible to invest the time & effort to balance the hell out of such a chaos-pack, but for one's own sanity, using normalized cells will save a lot of sanity & rework, and drastically decrease risks of catastrophic f-up. Don't do like this person! Do build weird electric systems though, unlike OP's way too broadscale doomsaying fear-mongering.

Re:What does a kilowatt hour look like? by keenerd on Friday September 23, 2016 @06:37AM (#12563552)
Charging the "pack" shown is impossible. There are no wires connecting any of the batteries.

He made a case that can hold a bunch of cells. Not a battery pack.

Re:What does a kilowatt hour look like? by gravypod on Friday September 23, 2016 @07:45AM (#12563823)
That's ever beginning of a larger project I assume.
Re:What does a kilowatt hour look like? by gravypod on Thursday September 22, 2016 @07:48PM (#12561312)
I came here to say just that. This is a horrible idea and definitely not something you should do.

Just use sealed AGM batteries, don't burn your house down or deal with spilling chemicals everywhere.

Even just drawing in parallel from batteries like this is a fire hazard. Charging is an out of your mind goal.

Re:What does a kilowatt hour look like? by userbinator on Thursday September 22, 2016 @10:03PM (#12561832)
Even just drawing in parallel from batteries like this is a fire hazard.

I think you've confused parallel with series; in parallel, the batteries will naturally balance themselves to the same voltage and discharge proportionally to their capacity. It's the series configurations that are riskier and need extra balancing circuitry.

Also, I'm pretty sure the bulk of fires are from the much more fragile pouch "lipo" cells, not hard-cased 18650s like these. You may note the extremely large number of lipo fire videos on YouTube as evidence.

On the other hand, 18650s tend to be quite a lot more robust and difficult to ignite:

https://www.youtube.com/watch?v=vi5lGtm_ItQ

https://www.youtube.com/watch?v=uoFRrmhXoVw

Re:What does a kilowatt hour look like? by qoobaa on Friday September 23, 2016 @04:24AM (#12563112)
I think @gravypod actually meant parallel connection, it might be quite dangerous in fact - you don't even need to draw anything from the battery to mess things up. If you connect a 100 cells in parallel and one cell dies creating a short in the circuit, the rest of cells will discharge through the shorted one. When you short a single 18650 cell, it outputs about 6-7 A of current on average. Multiplying by 100 gives you 600-700 A of current flowing through a single cell. That's why people use fuses to create parallel modules.
Re:What does a kilowatt hour look like? by gravypod on Friday September 23, 2016 @07:47AM (#12563838)
Yes that was mentioned in one of the maaaany EEVBlog videos iv watch that these fail closed sometimes as well as the recommendation that "you should never buy lipo cells without a built-in controller" comeing from a guy far smarter then I about electronics design. If he is afraid of it, it's for a good reason.
Re:What does a kilowatt hour look like? by throwaway7767 on Friday September 23, 2016 @10:29AM (#12564867)
> Yes that was mentioned in one of the maaaany EEVBlog videos iv watch that these fail closed sometimes as well as the recommendation that "you should never buy lipo cells without a built-in controller" comeing from a guy far smarter then I about electronics design. If he is afraid of it, it's for a good reason.

If you're building a large pack you don't want cells with a built-in protection. You connect all the cells to a pack-wide BMS that keeps things safe.

The important thing is to never use unprotected cells without some protection circuit in the pack.

Re:What does a kilowatt hour look like? by agumonkey on Thursday September 22, 2016 @08:16PM (#12561419)
Wow, as someone uneducated about anything related to electricity and power, seeing the picture in the article really made me want to emulate the setup. Not anymore.
Re:What does a kilowatt hour look like? by gravypod on Thursday September 22, 2016 @08:28PM (#12561470)
You joke buy many many people don't know how volatile battery chemistry is and how different charging of Lithium cells works.

I'd not have known how much of a bad idea this was had I not been a long time fan of EEVBlog. It's an entirely different world when touching Lithium cells. Even drawing in parallel from cells from the same batch can be a bad idea.

Re:What does a kilowatt hour look like? by Reason077 on Thursday September 22, 2016 @08:22PM (#12561445)
It's pretty safe so long as you use a battery controller with appropriate monitoring to prevent overcharging.

Recycled 18650 cells that have worked fine in laptops for years are very unlikely to suddenly explode on you for no reason. I'd be more worried about the mystery Chinese ones you can get new on the web!

Here's some Materials Science students at Oxford who built packs using recycled laptop cells. They used controller software that monitors the health of each individual cell:

https://m.youtube.com/watch?v=RW1Xugey8j0

(It's towards the end of the vid)

Re:What does a kilowatt hour look like? by gravypod on Thursday September 22, 2016 @08:29PM (#12561473)
It's still not the best idea unless you can control the draw from each cell individually. Hooking these up in parallel is a horrible idea.
Re:What does a kilowatt hour look like? by whamlastxmas on Friday September 23, 2016 @10:47AM (#12564991)
>very unlikely to suddenly explode on you for no reason

It really depends on their condition. If you get some cells from a laptop and they've all fallen down to reading 1 volt, then yeah repeatedly charging them (especially at a high amperage) is going to be pretty dangerous.

Re:What does a kilowatt hour look like? by userbinator on Thursday September 22, 2016 @10:31PM (#12561927)
I think your concerns are somewhat alarmist and tend to be a bit scaremongering. You may want to read an actual study about just how much HF is present in the fumes of burning cells. In this one, near the end they burned a whole laptop pack and analysed the gases that were emitted:

http://www.brandforsk.se/MediaBinaryLoader.axd?MediaArchive_...

The relevant datapoint is on page 61:

"As seen the yields of HF is much lower for the lap top cells, in fact the HF detected online was below the determined detection limit."

The graphs on page 101 also show HF concentrations below 4ppm --- and keep in mind this is basically all of the gases collected from the burning pack. Looking at the safety data for HF, the permissible exposure limit is only slightly lower at 3ppm and it's immediately dangerous at 30ppm.

In other words, it would be a bad idea to deliberately concentrate and inhale the fumes of a burning cell, but the HF probably isn't going to kill you. Some good ventilation of the area should be sufficient.

Re:What does a kilowatt hour look like? by spdustin on Friday September 23, 2016 @01:49AM (#12562589)
I had to come back because the paper doesn't specify the chemistry of the laptop battery; you can't use this as evidence to support anything other than caution around Li-ion batteries and cells.

And, more alarmingly, the part you omitted or glossed over: their plausible explanation for the lower HF detection (which, again, would depend wholly on the chemistry of the cells):

> the laptop cells exploded with liquid splashed on the walls in the equipment

Whoops.

Don't mess with these things unless you know how they can be safely tested, safely charged, and safely monitored. Li-ion protection failures (of various modes) were responsible for the Boeing Dreamliner fleet being grounded, Tesla refitting their battery packs (road debris caused a fire when it pierced a Li-ion cell), hoverboards being recalled, millions of dell laptops recalled after battery fires, and more recently, the Samsung Galaxy Note 7.

So, yeah. Safely tested, charged and operated is the key, and I wouldn't want to take that responsibility for a pack with as many batteries (and who knows which ones have their own standalone protection circuit in the cap) as in TFA.

Re:What does a kilowatt hour look like? by userbinator on Friday September 23, 2016 @06:30AM (#12563532)
And, more alarmingly, the part you omitted or glossed over: their plausible explanation for the lower HF detection (which, again, would depend wholly on the chemistry of the cells):

> the laptop cells exploded with liquid splashed on the walls in the equipment

The less electrolyte that gets burnt, the less HF generated, which I hope you agree is a good thing.

and more recently, the Samsung Galaxy Note 7.

How many actually burned? It's a very tiny fraction. Manufacturers recall precisely to avoid the sort of hysteria that statements like yours generate, and it's not any indication of impending doom. The aviation industry is particularly risk-averse, so it's not surprising. But I don't think the risk is very high compared to a lot of other things in our lives, especially when you consider all the lion cells out there of questionable quality in use and yet behaving themselves. China has taken the lead in making 18650s and other lion cells almost as easily available as alkalines, but reports of fires do not appear to have increased anywhere near in a direct proportion to that. (Reports of cells failing to meet capacity specs, on the other hand...)

By all means handle with care (as you should with any energy source), but lion cells are not lethal weapons that will instantly kill you at the slightest provocation.

Re:What does a kilowatt hour look like? by spdustin on Friday September 23, 2016 @09:22AM (#12564354)
Are you serious, or trolling? Weird question to ask outright, but I wanted to save time.

Regarding the battery exploding. Yeah, I'd agree that ... no! No, I don't agree at all! First, it exploded, so there's that. A cell in the middle of a multi-cell pack has nowhere to go. Second, it invalidated the experiment; they don't know how much HF would've been released in a real world scenario where the compressed cylinder of reactive metals and gasses is not free to "rapidly disassemble" into the air.

Now, moving on to Samsung's recall. How many failed? Sure, a small fraction. Do you know if yours will fail? How could you possibly know? Wait, I had something for this... oh, yeah. Safely test each cell.

Samsung didn't have that capability, their battery vendor didn't have enough engineers for all those house calls. You don't have that capability (you seem quite cavalier about the whole endeavor, so I'm guessing there). So, yes, since they can't know without testing, they recalled them all. What do you suppose they'll do then?

Probably, get together with the vendor, and test them.

Please stop suggesting to other readers that these things are perfectly safe when you know they're not. They're not tiny little bombs waiting to go off if you sneeze near one, but anyone using untested lithium-ion cells/batteries in untested configurations without a controller on each cell should be discouraged. We don't need a new category of Darwin award winners.

Re:What does a kilowatt hour look like? by spdustin on Thursday September 22, 2016 @11:46PM (#12562175)
The PF6 ions in the electrolyte of some Li-ion batteries (not all use the same chemistry) will readily combine with hydrogen in the air to form HF if the battery is combusting. Cylindrical Li-ion cells, like those part of an 18650 battery, literally hold their chemistry under pressure, and a thermal runaway will normally cause the vents in the cell to release the pressure.

If that's happening due to a short (which can and does happen when a cell is charged improperly, or even put under resistive load after the cell is discharged below a safe limit -- copper or other ions, depending again on battery chemistry, can literally bridge across the electrolyte to short the cathode and anode) the result of the release of pressure combined with the reactive nature of now exposed lithium is a small rocket that shoots a plume of gasses like sulfur dioxide or hydrofluoric acid. Again, this depends largely on battery chemistry, and without an MSDS on these particular cells, there's no way to know. But there's a reason why any chemist you care to phone up will say, if you tell them you're in possession of a cylinder of a compressed compound that contains fluorine (it won't matter what kind, fluorine really really likes to bond promiscuously and with reckless abandon), they'll tell you that you're braver they are. Tell them you're intend to string up a few hundred of them and pass an electric current into them, and they'll call a hazmat team for you.

A casual stroll through forums frequented by flashlight fans (yeah, it's a thing) and you'll see plenty of demonstrations of what happens when a Li-ion cell begins a thermal runaway. And plenty of memorials to those who gave up their passion because they're on ventilators after experiencing profound damage to their lung tissues. Hell, ask the firefighters that respond to a fire at a battery recycling plant; granted, that's a bigger scale than one cell, but even one cell in a small room can, depending on its chemistry and how violently it's outgassing, emit enough HF to cause lung damage.

Read an MSDS yourself: http://www.uscg.mil/hq/cg4/cg432/docs/msds/MSDS_LiIon.pdf

LiPo "pouches" mentioned elsewhere in this thread are much less likely to explode spectacularly before bursting, and much less likely to exhaust a plume of corrosive, toxic chemicals in their wake.

Re:What does a kilowatt hour look like? by rsync on Friday September 23, 2016 @08:51AM (#12564152)
"A casual stroll through forums frequented by flashlight fans (yeah, it's a thing) and you'll see plenty of demonstrations of what happens when a Li-ion cell begins a thermal runaway. And plenty of memorials to those who gave up their passion because they're on ventilators after experiencing profound damage to their lung tissues."

I was interested to read about flashlight enthusiasts on ventilators, but all I could come up with was this:

http://www.candlepowerforums.com/vb/showthread.php?141137-In...!

Re:What does a kilowatt hour look like? by userbinator on Friday September 23, 2016 @07:01AM (#12563639)
Cylindrical Li-ion cells, like those part of an 18650 battery, literally hold their chemistry under pressure, and a thermal runaway will normally cause the vents in the cell to release the pressure.

Unlike what you seem to be implying, lion cells are NOT "under pressure" in normal use. They are at atmospheric pressure. The vent is specifically so in case of abnormal conditions, it allows any pressure to escape instead of causing the cell to explode.

result of the release of pressure combined with the reactive nature of now exposed lithium

In a lion cell, there is no "exposed lithium" in the metallic, highly-reactive sense. It's a solution of lithium ions in an electrolyte, whose only real hazard is its flammability.

I believe I know the flashlight forums you refer to, and the incidents of HF poisoning too. Those were lithium primary cells, which actually contain significant quantities of metallic lithium and are definitely more reactive than lion. Even the MSDS you refer to says "in spite of their name, these batteries do not contain any lithium metal".

The MSDS is also the easiest way to scare yourself into thinking everything is highly dangerous. For example, look at the ones for sodium chloride. By the way, I would not trust that one so much as it gives a boiling point for ethyl acetate, a liquid at room temperature, of -84C. Similarly, dimethyl carbonate is listed as boiling at +4C, when that's its melting point. Perhaps that's where your impression that the cells are normally under pressure came from?

Likewise, I recommend looking at the data on the electrolyte solvents:

https://en.wikipedia.org/wiki/Ethyl_acetate

https://en.wikipedia.org/wiki/Diethyl_carbonate

https://en.wikipedia.org/wiki/Dimethyl_carbonate

Not totally harmless, but not insanely toxic either.

Re:What does a kilowatt hour look like? by Confusion on Friday September 23, 2016 @02:31AM (#12562720)
For those wondering about how nasty HF is: http://blogs.sciencemag.org/pipeline/archives/2004/03/03/thi...
Re:What does a kilowatt hour look like? by cmdrfred on Thursday September 22, 2016 @09:53PM (#12561795)
Maybe throw the whole mess into an out building with a fire suppression system of some sort? It says more details are to come, my curiosity is peaked.