The setup process for the Dropcam was absolutely magical. You plug a new one in, open the app and it would configure the camera via Bluetooth 4.0. You could then go back in and change WiFi settings by simply being near enough for the Bluetooth 4.0 connection.
Then Nest bought them, and completely removed that feature. They issued a firmware update that made it so now the camera that used to have this wonderful feature now requires me to plug it into my computer's USB and execute some janky app from a flash drive. Of course, if you buy one of their new devices, you a setup process somewhat similar to the original Dropcam. But existing customers are out of luck. In fact, the Dropcam Pro included a 1080P sensor but they did not enable it for various reasons. When Nest released their flavor of the camera, they enabled 1080P, but not for existing Dropcam Pro customers.
The DVR functionality is inferior too.
I wish I could get a refund. I personally feel like it is a bait and switch scenario. :(
The new Nest app on the phone is just now, finally reaching feature parity years and years later and its still not fully there. The 1080p debacle is terrible as well, they also compress the hell out of video now, it feels far worse than when I first got my cameras years ago (presumably to save on the storage space I'm paying quite a bit for).
It's funny, you rarely know the moment a company goes off the rails but I know exactly when it happened for me, for Dropcam.
I was out to dinner a year or so ago and all of us who had Dropcams got emails from nest about needing to migrate to nest accounts, and found that:
A) our access to our camera's was completely cut-off B) the migration process was completely broken, at first we thought just on mobile but it still didn't work when I got back to a computer, it took a few DAYS before I could migrate my account and access my cameras again.
This was terrible, I was 1000 miles from home and unable to access any of my cameras, I completely lost faith in the company at that moment and I know all of my friends did too.
Setting up cameras was removed from the (un-maintained) Dropcam App, to encourage users to migrate to the Nest app, which has more ongoing development.
The video on cameras is no more compressed than it ever was. I know it can feel worse, but nothing has changes there.
(source: I work at nest)
that said, it is a core component, and basically the innovation/disruption if you even want to call it that, that the conpany was providing. i mean without a clean wireless interface, its basically a webcam/thermostat ect on a hone depot timer
You can't feasibly stream someone's IoT camera from their home via BT; any kind of hack like that happens over Wi-Fi or Ethernet connections.
Did you find those to not be issues? Definitely most of the reviews were good, so maybe it's just isolated people having problems. But I couldn't tell if it was that, or more that people either aren't as picky about UX as I am, or they didn't have another point of comparison... I'm very open to re-considering them if someone can convince me this stuff is a non-issue, because the remote sensor would certainly make our system work better.
My thermostats are in areas that are not indicative of the actual room temperature at all so the sensors are useful for me. I don't have a more complicated setup with dampers to divert air to a specific room, but that could be a cool addon if they made it compatible.
They're not 'machine learning' thermostats, but they work predictably, reliably well. Cheaper than a nest, too..
If you are thinking of the Ecobee, do it! :)
That's the problem with so called 'lazy zoning'.
However that being said, if you want something like this and don't have an ecobee, SmartThings starter kit comes with multiple sensors that read temperature.
My folks have an Ecobee and if I didn't have a Nest already, I might consider it. The remote sensors are a huge plus.
The Nest cannot, well it CAN, but you lose fan control in the process making it worthless. I never understood why no thermostat supports alternative power, considering tons of property would be an easy installation without the rarely available C wire.
Quick shout out for the Honeywell Wi-Fi Smart Touchscreen Thermostat. It too requires the C wire, costs the same as Nest, but has a much better touch interface than the Nest while providing the same-ish automatic functionality.
Read page 12 of their guide. The PEK requires additional connectors that not all systems even have. A lot of people will lose fan control, just like the Nest.
> Also, the C wire is not rarely available, basically any house since the early 90s will have one already wired up
Our house was built in 1998, doesn't have it, a coworker's house was built in 2005 and had to get it installed for their Nest ($120 callout + $120 in time), the in-laws returned a Nest because their home from roughly 2001-02 lacked it. Where are you getting this information? There's nothing in building codes that requires running the C wire, so builders will only run it if the thermostat requires it and most included ones do not.
> any house that has upgraded hvac unit in say the last 15 years will have the capacity to install one by running a wire to the mainboard.
Running wires behind walls isn't trivial in an already built home. Least of all if you're going up two to three floors.
Also have a relative in an older development that used the PEK and he can control his fan independently of the hvac just fine... I've actually more commonly heard of some control boards that mess with the fan if you use the C wire rather than the power extension kit, since the control board basically fakes the C wire using the G wire as the Nest does if you don't have a C wire. The PEK works differently.
You don't need a C wire for a programmable thermostat. The other channels provide power, the C wire just provides more. It is useful if you want to run a color LCD screen or WiFi. If you have a thermostat with a black & white calculator-like LCD, it likely doesn't have a C wire running to it.
> I've actually more commonly heard of some control boards that mess with the fan if you use the C wire rather than the power extension kit, since the control board basically fakes the C wire using the G wire as the Nest does if you don't have a C wire.
What? That would burn out thermostats. How would the control board know to pass 24Vac through a low voltage line? Can you link anything to this "common thing" that control boards do? Sorry but I'm extremely skeptical of that, it doesn't even make sense from a thermostat signal point of view, since they'd just assume you would run C if C was required during installation rather than doing the hack you're suggesting here.
The reality is that C isn't required on almost any included thermostat, programmable or simple. Good installers run the C but terminate it, bad installers just don't run the unneeded C. I've never heard or read about a first party control board which acts like a bypass kit out of the box, and I don't even understand the point.
With that said, the Ecobee that I bought off eBay included the PEK. It required a few hours up in the attic but was easier than I thought it was going to be.
From what i can tell, this is wrong. I asked 30 builders in 3 states (a mailing list), and every single one of them basically agreed with the statement that they have put them in all homes they've built since 1990.
The truth is, AFAIK, the largest homebuilders in the US do it as a matter of policy.
The building code does not require running low voltage wiring (including RG6) anywhere, either, but most do it nowadays.
I really think you are wrong about this :)
In my old house from 1950s the furnace had the terminal so I just ran a new wire. Easy if you have some fishtape or something similar. Kind of depends how far your thermostat is from your furnace though.
It's wrong for any of these thermostats to be using these wires for power. That is not the purpose of those wires. For that matter, it's shit engineering to require the thermostat be mounted on the wall hooked up to those wires like your old thermostat. The purpose of those wires, with their 24V AC, is to toggle relays. They could just as easily be done directly _at the furnace_, or just have a low-power battery powered radio module on the relay wires, with a WiFi or other wireless receptor talking to your sensors elsewhere, and with an app on your phone or tablet to control it.
Nest is an absolutely terrible design that everyone else copied. Its terrible design is crap for installation, customer support, and maintenance. It's needlessly complex.
But it looks nice?
Now, these bypass kits or similar, are a little hacky. But you're talking about the C wire itself being so, which just isn't the case. IF you have one available that is exactly what it is design to do.
But, yes, I'd prefer USB at the thermostat.
Or, you can also install a wire saver: http://www.amazon.com/Honeywell-THP9045A1023-WireSaver-Prest...
I switched to an Ecobee3 system and found it was far superior in many ways. Alexa integration, remote sensors (for actual temperature measurements in rooms), easier install and compatibility if you don't have power going to thermostat, better wifi, touchscreen interface.
With Google Home coming I wonder what this means for Nest. Maybe it will be fully absorbed into Google?