Re:Building a 3D Printed Electric Jet Powered Snowboard
by donpdonp on Wednesday April 08, 2015 @08:39PM
(#9345125)
The amazing part is the energy density and discharge rate of LIPO batteries. Also the ducted fan is impressive for its size. As a hobby project its fun to watch. As a consumer product, the noise pollution would turn the average alpine ski resort into the audio equivalent of a highway.
Re:Building a 3D Printed Electric Jet Powered Snowboard
by darkmighty on Wednesday April 08, 2015 @09:04PM
(#9345203)
I like the idea. If you have a surface to react against, why not use it? It doesn't change the functionality, so it isn't just becoming a snowmobile as others claim, you just have to set it up so it maintains ability to slide.
I think a pair of small tracks on the back with some kind of speed sensors to make it coast without drag is ideal (think bike coasting system with drag compensation).
Re:Building a 3D Printed Electric Jet Powered Snowboard
by scoggs on Wednesday April 08, 2015 @07:22PM
(#9344834)
He would either need to cut a space for the track into the board (there goes an expensive board if the results are poor) or put two tracks on either side of the board like training wheels. I don't think either makes sense as the first is too destructive and risky and the second will severely limit turning even more and most likely add unneeded weight.
Re:Building a 3D Printed Electric Jet Powered Snowboard
by bri3d on Wednesday April 08, 2015 @08:51PM
(#9345164)
I've never understood this brand of 3D printing detraction - yes, I could absolutely make 80+% of the "glue" parts I make with my 3D printer using crap from the hardware store.
But then I would have to know what crap I needed in advance, and go to the hardware store. I like getting to be extra lazy, and 3D printing facilitates that nicely. The end result also usually functions well and looks great.
I personally wouldn't have designed that EDF mount the way it was designed, but it works and I can't argue with the totally cool end result.
On a side note I'm super glad the author of this blog post used LiPo fire bags. I thought the hype about LiPos as bombs was overblown until one in my homemade electric bike caught fire on the charger once. I was very lucky that I always kept the bike outdoors on my porch, but never again! Always on concrete, in a bag from now on.
Re:Building a 3D Printed Electric Jet Powered Snowboard
by toomuchtodo on Wednesday April 08, 2015 @04:34PM
(#9343749)
Depending on the fuel, gas turbines can be much safer. The current and voltage he's working with is fairly dangerous for close contact, where it takes a great deal of effort to ignite kerosene or diesel fuel in an open air environment.
Re:Building a 3D Printed Electric Jet Powered Snowboard
by kposehn on Wednesday April 08, 2015 @04:58PM
(#9343935)
Ah, ok. That makes more sense now.
Still, I would expect the massive heat output of a gas turbine to be another danger as well. You are, after all, spitting extremely hot gases out the back, which could pose a great danger to anyone behind and might also melt a large amount of snow. Probably depends greatly on the method of mounting it though...
Re:Building a 3D Printed Electric Jet Powered Snowboard
by erobbins on Wednesday April 08, 2015 @06:20PM
(#9344483)
It wouldn't, and it would suck fuel like crazy. Fans aren't optimal for low speed thrust.. turbojets even less so :) 2 fans would be much better than 1 jet.
I think this idea could disrupt the powered snowboard industry.
I think a pair of small tracks on the back with some kind of speed sensors to make it coast without drag is ideal (think bike coasting system with drag compensation).
But then I would have to know what crap I needed in advance, and go to the hardware store. I like getting to be extra lazy, and 3D printing facilitates that nicely. The end result also usually functions well and looks great.
I personally wouldn't have designed that EDF mount the way it was designed, but it works and I can't argue with the totally cool end result.
On a side note I'm super glad the author of this blog post used LiPo fire bags. I thought the hype about LiPos as bombs was overblown until one in my homemade electric bike caught fire on the charger once. I was very lucky that I always kept the bike outdoors on my porch, but never again! Always on concrete, in a bag from now on.
http://www.jetcatusa.com/p200.html
Still, I would expect the massive heat output of a gas turbine to be another danger as well. You are, after all, spitting extremely hot gases out the back, which could pose a great danger to anyone behind and might also melt a large amount of snow. Probably depends greatly on the method of mounting it though...
https://www.youtube.com/watch?v=XJARrc40imk
or with bigger propeller : https://www.youtube.com/watch?v=C_UtPmb3Z-o (in the San Carlos museum btw)