Re:A 3D printed toothbrush for all your teeth
by trafficlight on Tuesday October 01, 2013 @01:50PM
(#6477797)
I don't know, 6 seconds of brushing sounds pretty good.
[ Parent
| on HN ]
Re:A 3D printed toothbrush for all your teeth
by jlgreco on Tuesday October 01, 2013 @01:52PM
(#6477813)
Agreed. At that point it becomes something I could actually see myself doing after every meal.
Re:A 3D printed toothbrush for all your teeth
by phogster on Tuesday October 01, 2013 @02:02PM
(#6477912)
Isn't there a thing as overbrushing?
Re:A 3D printed toothbrush for all your teeth
by jlgreco on Tuesday October 01, 2013 @02:10PM
(#6477975)
Probably; all I know is that my dentist always tells me I should brush after all meals. However that is probably assuming the standard "3 meals a day" instead of the modern American "continuous meal throughout the day, with occasional breaks for breathing".
Re:A 3D printed toothbrush for all your teeth
by DanBC on Tuesday October 01, 2013 @02:48PM
(#6478249)
Modern advice is to brush before eating. You clean the teeth so stuff doesn't stick to them. Brushing after eating brushes when your teeth are being attacked by acid.
(http://www.nhs.uk/Livewell/dentalhealth/Pages/Teethcleaningg...)
> When should I brush my teeth?
> Brush your teeth for at least two minutes in the morning before breakfast and last thing at night before you go to bed.
> Never brush your teeth straight after a meal as it can damage your teeth, especially if you've had fruit, fizzy drinks, wine or any other food that contains acid.
> This is because tooth enamel is softened by the acid and can be worn away by brushing. Instead, wait an hour after a meal before brushing your teeth to give your saliva chance to neutralise the acid.
Obviously, I'm not a dentist and nothing I say is meant to replace anything an actual dentist tells you.
Re:A 3D printed toothbrush for all your teeth
by jlgreco on Tuesday October 01, 2013 @03:31PM
(#6478537)
Huh, that makes sense at least; I'll have to look into that.
Re:A 3D printed toothbrush for all your teeth
by knappe on Tuesday October 01, 2013 @02:42PM
(#6478205)
Yep. Over-brushing can cause your gums to inflame and retreat, lowering the gum line. There is also no fix to this problem short of surgery. Wish I had known that when I was younger.
Re:A 3D printed toothbrush for all your teeth
by EvanAnderson on Tuesday October 01, 2013 @02:21PM
(#6478054)
The only damage that I've ever read about re: over-brushing has been enamel damage caused by abrasives in toothpaste. The bristles of the brush should be much softer than enamel.
Re:A 3D printed toothbrush for all your teeth
by npsimons on Tuesday October 01, 2013 @03:00PM
(#6478337)
My dentist had to fill in spots near my gums on my upper molars that were worn down; I seem to remember him telling me not to brush so hard.
Re:A 3D printed toothbrush for all your teeth
by marcosdumay on Tuesday October 01, 2013 @05:48PM
(#6479302)
I had this problem for ages, in the end, the actual problem was gastrits. Any gastric problem has that same simptom, so if it persists, go check for them.
Re:A 3D printed toothbrush for all your teeth
by tripzilch on Wednesday October 02, 2013 @05:22AM
(#6481455)
I don't doubt you, but that might also have been advice for after the filling perhaps? The stuff they fill it with is not nearly as hard as the stuff on the outside of your teeth (which is pretty damn hard). So a filling will always be a weak spot.