One part of this is the batteries. When you have the amount of batteries needed to drive a truck for a reasonable distance, you automatically get a high amount of power output as well. The power is distributed over many cells, so no overload there.
EV motors are significantly smaller than their ICE counterparts, they’re relatively cheap, don’t require significant maintenance and they generate much less waste heat for a given power output. Adding more motors+inverters to handle the required power is not over engineering in the case of an EV truck, it’s just good engineering. I suppose it’s even necessary to some degree, to deal with the lack of a multi speed gear box
As mentioned in the other comment, the problem is often overheating in brakes. This is also less of an issue with EVs. You can distribute the energy dissipation to the motors/batteries and the brake pads, so the heat load is less concentrated. Energy sent to the batteries is absorbed as energy stored, with very little waste heat.
Or downhill...[0].
I'll get my coat...
In normal use, only one phase is active an a time, so the duty cycle is 1/3. When the motor slows almost to a stop, the duty cycle on that winding is 100% meaning that the effect of that current on heating the wire is much worse than normal.
The catastrophic failure is when the MOSFET fails in a way that it doesn't protect the winding or battery from a short circuit which could lead to runaway heating in the battery as well as the motor. But even before then, unless the controller is actively limiting current to safe levels, the motor will get destroyed.
The only happy day scenario is if the motor control is actively limiting the current to safe levels well below the expected failure point, and then the EV will just fail to move at all under that load, other than rolling backwards.
As I said, the limit for this will be based on what the manufacturer expects the maximum load will be, but people have a knack for trying to carry more weight than their vehicle was designed for, or taking it places that are unsuitable. That's just humans being humans.
It's possible to design an EV that could withstand significantly steep hills with heavy loads, e.g. by putting many more sets of individually wired windings in parallel, but it'd be expensive and unnecessary for the typical situations that they'd be used in, and so unlikely to be commercially viable.
The problem isn't overloading the engine when you go up, it's overheating the brakes when you go down. The reasoning here is probably that EV semis will use regeneration for some of the braking thus avoiding the overheating to some extent.
Even if it’s an engine issue, I don’t see how an EV would be more likely to catastrophically overheat. An EV will generate a lot less heat for a given amount of power. There’s also less potential for oil and fuels leaks which exacerbates the issue.
Friction brakes convert momentum into heat. If you ride the brakes going down a mountain you generate more heat than the brakes can dissipate into the air and the brake temperature keeps going up until they're hot enough to start a fire.
A quick search says it heats the engine less than accelerating, so shouldn't cause overheating.
https://en.wikipedia.org/wiki/Compression_release_engine_bra...
Are you sure? I'm pretty sure I can engine break with my diesel car and do that pretty often in fact. Or I misunderstand what engine breaking is.
Your car also has rolling resistance and aerodynamic drag to contend with. Might work well at slowing a passenger car, not so much with a 50K lb. vehicle, hence the Jake brake.
I like to believe I'd recognize the difference, especially since it's a manual car and I can tell the difference between letting it roll in neutral and shifting down a gear which slows down the car :) Maybe it's not that it doesn't work on diesel cars but the effect is just less than with petrol?
A diesel engine does not have a throttle valve. Engine speed is controlled purely by the amount of fuel being injected. This is why diesel engines can "run away" if an uncontrolled fuel source such as oil leaking from a turbocharger enters the intake, and why older pre-computerization diesels can be smoky under hard acceleration (or any time if poorly tuned). When you release the accelerator the engine stops receiving fuel and thus stops producing power, but aside from friction there's nothing working to slow it down. Air is sucked in more or less unrestricted and some energy is spent compressing it as the pistons rise in the cylinders, but much of that energy comes back out as the pistons come back down so the only energy loss in the system is what's converted to heat. You would get the same effect in a gasoline engine if you shut off the fuel pump but kept the throttle wide open.
But such a gradient would be completely unusable for any ICE! EVs can deliver an absolutely insane amount of power at even the slowest speeds. If an EV has the power to sustain highway speeds, it'll also have the power to go up a steep hill at a snail's pace. On the other hand, an ICE will struggle significantly with steep hills - even if they technically have the horsepower to do it.
I highly doubt it'll result in a fire, though. Measuring motor current isn't exactly rocket science, so it'll just go into an overload mode. Heck, I wouldn't be surprised if EV motors were explicitly designed to survive short-term stall currents. Measure the wheel speed and it's pretty obvious to figure out when you're stalling and should shut down to avoid damage.
Most EVs are direct drive from the motor without a gearbox. There absolutely is a minimum speed depending on how the motor is wound. If you imagine, say 12 magnets around the motor driven by 3 phases, the idea is to have one winding attracting the magnets, and this phase is the one the motor is "trying to get to". In this situation, this winding is active until the motor is in the correct position (actually slightly before) when it is depowered and the next phase is powered. The longer the motor stays in that position, the hotter the winding gets for the same current. At the point where the motor stops being able to rotate at all, that winding is receiving 100% duty cycle.
There are strategies that you could try - the simplest is cutting power and letting it cool down, but then the motor will stop where it is, and starting the motor from stationary requires even more power than keeping an already moving motor going. You might apply a reverse polarity to the previous winding for a bit to repel the magnets and then swap back. If the motor has passed the mid point this will be less effective, but still better than nothing.
If you ignore feedback from the axle and just cycle through the windings at the desired speed, then there definitely is a minimum speed. Because when the load is too great and the motor doesn't move and you cycle to the next phase, then next phase won't exert much magnetic field on your magnets and the next phase after that, you're working against the direction you want to go.
It's true that if you gear an EV motor, the torque should be able to be geared down to any speed. But typically pure EVs are direct drive, because usually they have enough torque for the low speeds and adding a gearbox just adds inefficiencies. But for a heavy load, maybe gearboxes are required. As a disclaimer, I don't know if EV trucks have gearboxes or not, but certainly EV cars tend not to have except for hybrids.
I'm actually not so sure. If the gradient is so steep that the vehicle is struggling to move at all, the current through the motor windings will be very high, causing the windings to overheat, potentially fail and potentially short circuit. There's a high risk of damaging the MOSFETs in the motor controller, which very much could lead to a fire risk depending on the failure mode.
There's not really many ways to solve this problem - in a normal 3-phase winding, all you can do is remove the current until it cools down and try again, but that will force the motor to stop and then try to restart, so creating an even larger load. Possibly if you have 6 more more phases and more magnets such that each of the normal 3-phases has multiple windings and magnets, you can cycle through the different ones and still keep applying some torque, but obviously this would still not really solve the fundamental problem.
Essentially the problem is the same for ICE vs EV - if the gradient is so steep and load so heavy that the engine / motor can't provide enough force, then it will be overloaded. Whether that's through pressure / shearing / excess heat in an ICE or through excess current / excess heat in EV, the outcome is failure to continue forward at best.
The only real solution is to massively over engineer the engine for normal situations, but human nature being what it is, there will always push things way beyond the designed limits and safety margins until it fails.