Re:United finds loose bolts on plug doors during 737 Max 9 i...
by lucisferre on Monday January 08, 2024 @04:33PM
(#38918485)
Why would the softness matter for torque, if there has been some shift or compression since original install the torque should still ensure the correct pressure between the fitting, no?
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by kube-system on Monday January 08, 2024 @04:43PM
(#38918614)
Soft materials develop wear more easily.
e.g. any slight boogering of the threads of a used fastener could translate into rotational torque that doesn't end up being converted to a clamping force.
(or in more extreme instances, some fasteners are torque to yield, and change shape after their first use, and must be replaced. But I'll presume that's not what they were talking about here)
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by Scoundreller on Monday January 08, 2024 @04:38PM
(#38918549)
That’s assuming then original install torque spec was correct.
Much easier to strip aluminum threading if you over torque. Steel tends to just bend (and bend back better).
Aluminum also fractures while steel bends/stretch back and forth better.
(This is mainly from my experience working on bicycles, and a little auto)
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by etrautmann on Monday January 08, 2024 @04:39PM
(#38918562)
A major concern is presumably over-torquing a screw and causing partial failure of threads in the material. This could be subtle and difficult to detect, but present as a problem over time.
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by lupusreal on Monday January 08, 2024 @04:50PM
(#38918686)
Aluminum has no fatigue limit, so you really need to do things by the book.
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by the_third_wave on Monday January 08, 2024 @04:41PM
(#38918590)
> If you’re using new parts, sure, but once they’re old/re-used parts
Most service manuals require new bolts, fasteners and washers for torque-critical parts.
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by HPsquared on Monday January 08, 2024 @04:48PM
(#38918663)
Skipping that part is even more ubiquitous than failure to properly torque. It takes a lot of effort to buy the correct bolts, only specialists have them to hand for a given make. Even dealers might not have every bolt. So it means you need to procure many more parts you would otherwise (the part you're replacing, plus 20 specific bolts with part numbers).. Most mechanics don't bother unless it's something really big like cylinder head bolts or an axle nut.
Re:United finds loose bolts on plug doors during 737 Max 9 i...
by the_third_wave on Monday January 08, 2024 @06:00PM
(#38919641)
That is probably valid reasoning when talking about a neighbourhood mechanic dealing with all brands but it does not hold for an aircraft maintenance shop. Skipping this step makes them liable for any problems caused by failure of related parts so I assume [1] they keep to the book in this respect. Anyone here who has experience with one of these shops want to chime in? When I work on machinery I tend to follow the rules when dealing with stretch bolts since these do tend to fail far more often when re-torqued but for normal (non-stretch) bolts I do often reuse them if they're in good enough shape. I work mostly on farming/forestry equipment and our personal vehicles though, not on airplanes.
[1] which makes an ass (out of) u (and) me
Given the amount of (soft) aluminum on aircraft, (737 is 80% aluminum), it would be insane to not precisely consider torque.
Steel on steel is more forgiving.