I have this mentality with my normal on grid tract house. My saying is "at least I know what corners I cut"
One of HN’s most important comments on this subject ever IMHO
This sounds similar to the NIH syndrome in some software companies. I’m still trying to figure out when it makes sense and when it doesn’t. In software, I tend to err on the side of NIH. In life, I am almost never DIY. I suspect I’m out of balance in both regards.
Eg if "search" quality is a competitive differentiation, make sure you implement search yourself. Your goal is to beat the rest of the market in search quality so buying a commodity search product that anyone else can buy doesn't make sense. You are directly rewarded for paying the extra NIH cost to go the extra mile for your customers.
For everything else, there's little benefit to paying the extra cost of NIH. An excessively fancy/powerful support ticketing system, for example, isn't going to help you get more customers. Few people might care how much nicer the checkout/payment page is than on other products, so you can outsource that.
Most areas in real life don't benefit from extra quality either. For eg, the extra quality you might get from hunting/farming your own own food makes little difference to most people, so most choose to outsource that.
The zone is not ideal for wind or solar, so we are connected to electrical. We had a contractor help with bath tiling, he did plumbing and electric hook-ups, an electrician did what was required by code for the electric system.
Every single one of the licensed pros had cut corners.
The electrician did not secure the outlets to the walls properly, just enough for them to start getting loose after 2 years. One weak screw instead of four. I was afraid of electric for a while. Only had the energy to read the code, some books and watch some youtube videos and re-secure all the outlets and set up 2 extra outlets, with channel cable dragging, etc, about 3 years ago.The plumbing had multiple mistakes as well, wrong tank positioning, wrong main drain placement, no main cut-off to the tank, did not get a filter hook-up or a drain valve, etc, and the hot water boiler did not get a proper set-up for easy maintenance (the magnesium sacrificial anode cannot be removed, too close to the ceiling, you have to dismount the whole unit).
If I had the money and not to have to work during the build process, I would have built a small house first, learning everything about how to do it right and observing the "pros" as they go along. But hey, we have a house that total spend was 1/3 of the market, enough land to build a second one, and I am a different man from the experience.
It was my first experience with engineering outside of software. Trust no one, do your own research, plan, experiment and verify apply even more in "physical world" engineering.
It's nice to become more and more self-reliant with construction skills. I just serviced the indoor plumbing, changed 3 taps, installed a water-filter hook-up and filter, including pipes, and plan to assemble a big water filtration system, myself, in the summer. $ 5K to 7K for filter tank, controller and installation by contractor, vs $600 for system and medium from manufacturer, and install it yourself.
Whether you plan to go off-grid, build, be your own general contractor, or even just buy a property, doing things yourself, provided you can follow engineering principles and values, is always the best bet. You want reliability. The pros want to make a profit.
Life pro tip - if planning to participate in construction in any way, audit the locality and how strict vs smart their code and inspections are.
Get a Rheem Marathon hot water heater and permanently do away with sacrificial anodes.
So much about construction drives me nuts. After sweating bullets over microscopic details of software design to find the balance between durability, longevity, readability, reliability, maintainability, security, etc., it comes as a huge shock to see the lack of attention to detail in most "professional" construction.
On the other hand, most people aren't as bothered as I am about spending so much of a lifetime paying for a good that deteriorates to pretty much nil at the the end of that lifetime.
Construction and materials "solutions" that are by design planned to fail by the end-of-life / warranty, etc.
I was contemplating what to do about that with my water heater, but I think maybe the procedure is that you cut it up as it comes out, if it is one long piece, and there are replacements that are segmented so you can get them back in with limited clearance.
Some handy individuals have modified their existing assemblies, but I don't have the time nor the tools, and it's not cost-effective to mess around in my case, as a replacement for my electrical unit will be under $300, dealer demo unit, with own installation. Just have to snag one on sale.
Few plumbers or electricians are willing to make a 2-or-more-hours round trip on the road at any price. If you have an off-grid home you're not willing to maintain, you're going to spend a lot of time sitting alone in the cold and dark until nature finally recycles you.
I live off grid, I have nothing but reliable systems here. Stuff breaks every single day. Nature happens - we get lightning strikes, floods, fires, freezing temperatures, droughts - stuff breaks.
When we moved here, some stuff had been done by the previous owners. No plans or anything, just "hunt the burst water line under the concrete" and all that fun.
The major advantage of DIY is that you end up being able to repair your own stuff, to know how it works, to know where it is.
If you have an off-grid home that you can't maintain, you aren't going to last long there.