News for hackers. Stuff that matters.
Re:First commercial curved CMOS sensor from startup CURVE by supernova87a on Tuesday December 15, 2020 @08:28PM (#25437906)
Oh, this is even more interesting after looking into it (see this diagram from another site): https://www.dpreview.com/news/7542036825/french-startup-is-p...

The curvature goes in the opposite direction of what I would have thought. I would've thought the orientation of the curve was in the sense of maintaining a "constant radius" from the end of the lens stack. (exit pupil?) I.e. the curve helps bring in the distant parts of the sensor closer and more orthogonal to the light rays.

But the diagram shows the opposite kind of curve! That makes even less intuitive sense to me.

(I can't imagine someone not involved with the company creating this diagram, or it being so wrong and not being caught by some review process? I figure the diagram is legit? Someone drawing ray tracing level details would get it so wrong?)

Re:First commercial curved CMOS sensor from startup CURVE by bgee on Tuesday December 15, 2020 @08:39PM (#25437986)
The illustration also contradicts the real picture of the sensor.

Also from the same DPReview article: "Curved image sensors mimic the human eye", that illustration is not how I thought the retina is shaped.

Re:First commercial curved CMOS sensor from startup CURVE by m463 on Wednesday December 16, 2020 @02:18AM (#25439933)
The image of the sensor held by the fingers looks concave.

The illustration with simplified optics shows a convex sensor.

Hard to figure it out.

I would imagine chromatic abberation and light dropoff is due to flat sensors and concave sensors would help. But I might not understand modern lens design.

Re:First commercial curved CMOS sensor from startup CURVE by sudosysgen on Wednesday December 16, 2020 @11:27AM (#25444459)
It depends on the lens. Some lenses will more easily want a sensor that curves away, others will prefer a sensor that curves towards them.
Re:First commercial curved CMOS sensor from startup CURVE by londons_explore on Tuesday December 15, 2020 @03:02PM (#25434420)
Making CMOS sensors from scratch is very much not a thing for a thrifty startup to achieve...

Yet submitting a design to a commercial fab and saying "make it curved plz" isn't likely to work either.

So how is this done?

Re:First commercial curved CMOS sensor from startup CURVE by wmf on Tuesday December 15, 2020 @03:22PM (#25434711)
If you thin a silicon die enough it becomes flexible. I suspect they're using a standard planar fab then thinning the die and mounting it on some curved substrate.
Re:First commercial curved CMOS sensor from startup CURVE by nickff on Tuesday December 15, 2020 @03:40PM (#25434960)
They may even just be using relief cuts in the die to produce the effect. Reliefs have a number of advantages, including reducing twisting and buckling.
Re:First commercial curved CMOS sensor from startup CURVE by londons_explore on Tuesday December 15, 2020 @03:43PM (#25434992)
But not flexible in 3 dimensions...

(Ie. You can curve it around a cylinder, but not around a sphere)

Re:First commercial curved CMOS sensor from startup CURVE by grovellogic on Wednesday December 16, 2020 @11:42AM (#25444668)
If you want to dive deeper into the issues look into Developable Surfaces https://en.wikipedia.org/wiki/Developable_surface
Re:First commercial curved CMOS sensor from startup CURVE by sudosysgen on Tuesday December 15, 2020 @03:48PM (#25435043)
Wouldn't different thicknesses allow this?
Re:First commercial curved CMOS sensor from startup CURVE by vel0city on Tuesday December 15, 2020 @07:01PM (#25437172)
Take a sheet of paper and wrap it around a ball. Notice how it folds?

If you could take a flat surface and have it represent the surface of a sphere without warping (or vice-versa), we wouldn't have constant debates about what kind of map projections are best.

Re:First commercial curved CMOS sensor from startup CURVE by plasticchris on Tuesday December 15, 2020 @11:13PM (#25438976)
Maybe you could make it like an orange peel and bend it mostly sideways? Depends on how rigid it is. Or cut ridges like a fresnel lens? Or like lasik? All depends on the material properties.
Re:First commercial curved CMOS sensor from startup CURVE by sudosysgen on Tuesday December 15, 2020 @07:25PM (#25437382)
Yes, I agree. What I mean is that by varying the thickness, you can get it very close to or exactly a sphere.
Re:First commercial curved CMOS sensor from startup CURVE by ChuckMcM on Tuesday December 15, 2020 @03:59PM (#25435185)
Good question. I don't know but I know from another effort that was at Sun way back in the day it is really difficult to create curvature in a system that wants flat optical masks and flat processing.

There are at least two challenges, one is curve itself, and the other is laying out the sensor to be linear across the curved surface. I'm wondering if they are going to do a Hot Chips presentation, that has been where most of the coolest advances in chip making have been detailed.

A friend speculated they might be doing a mems sort of thing where they make a 'thick' chip and then etch down to the layers of sensors, perhaps polishing, as a glass lens might be made, but for me that seems like it would be too risky. Thinning and bending is a possibility of course you need to account for the final topology in your layout.

Definitely a fun puzzle to speculate about.

Re:First commercial curved CMOS sensor from startup CURVE by m463 on Wednesday December 16, 2020 @02:23AM (#25439959)
Although wafers seem easy to make flat, I wonder if lithography itself might work better on a curved target.
Re:First commercial curved CMOS sensor from startup CURVE by bhouston on Wednesday December 16, 2020 @09:56AM (#25443223)
there are lenses in the lens assembly that flattens the image. Thus if you wanted to make curved wafers you could remove these. But then the curve would be across the water itself and maybe not what you want on the individual chip level.
Re:First commercial curved CMOS sensor from startup CURVE by Darthy on Tuesday December 15, 2020 @03:56PM (#25435140)
That’s not the first - Sony already released a product with a curved sensor in 2014, the KW1: https://www.sonyalpharumors.com/sony-confirms-kw1-perfume-se...
Re:First commercial curved CMOS sensor from startup CURVE by giuliomagnifico on Tuesday December 15, 2020 @04:09PM (#25435297)
Right but the Sony one is a small 1/2.3-inch, this one looks like a Full Frame 35mm sensors.

Edit: I think "the first one" is the claim for "very first commercial curved sensor for a scientific application"..."for a scientific application" they said, Sony was a selfie camera :-)

Re:First commercial curved CMOS sensor from startup CURVE by bombela on Tuesday December 15, 2020 @05:19PM (#25435991)
So (1/(2.3)) inch == 11mm vs 35mm for the new one?
Re:First commercial curved CMOS sensor from startup CURVE by mark-r on Tuesday December 15, 2020 @08:27PM (#25437893)
Sensor size designations are very confusing. The 1/2.3 is based on the diameter of an old tube sensor, of which a large portion couldn't be used for imaging. The 35mm is based on 35mm film, which was actually 24mm x 36mm. The only way to make sense of it is to use a table showing actual dimensions, such as https://en.wikipedia.org/wiki/Image_sensor_format#Table_of_s....
Re:First commercial curved CMOS sensor from startup CURVE by Exmoor on Tuesday December 15, 2020 @08:22PM (#25437863)
~6.17mm vs 35mm width or 7.66mm vs 43mm for diagonal, which is probably a better measure since the aspect ratio is different.

Source: https://en.wikipedia.org/wiki/Image_sensor_format#Table_of_s...

Re:First commercial curved CMOS sensor from startup CURVE by jbay808 on Tuesday December 15, 2020 @03:39PM (#25434944)
Is this in any way related to this earlier HN submission about Sony's patent on curved sensors?

https://news.ycombinator.com/item?id=25113755

Re:First commercial curved CMOS sensor from startup CURVE by giuliomagnifico on Tuesday December 15, 2020 @04:03PM (#25435230)
I don't think, Sony made a patent, this startup the final camera CMOS.
Re:First commercial curved CMOS sensor from startup CURVE by supernova87a on Tuesday December 15, 2020 @03:12PM (#25434565)
Interesting!

Do they start with a curved piece of silicon and do the fabbing on that? Or is it initially flat and then bent during the process?

Will this be generally isolated to very specialty wide-field imaging? And expensive, custom runs?

Re:First commercial curved CMOS sensor from startup CURVE by BostonEnginerd on Tuesday December 15, 2020 @03:22PM (#25434709)
I would expect the sensors are manufactured flat, back thinned down to where Si is flexible and then mounted onto a curved support structure.

It looks like their US patent is here: https://patentimages.storage.googleapis.com/10/b3/ee/69d396b...

Re:First commercial curved CMOS sensor from startup CURVE by supernova87a on Tuesday December 15, 2020 @06:03PM (#25436570)
How interesting!

By the way, this brings back thoughts how astronomy used to be done with thin glass plates, doing wide area sky surveys. The plates would be placed into the plate holder, and some pressure was necessary to deform the plate to match the curvature desired.

They said you knew when you'd gone to far because you'd hear the tinkle of broken glass...

(they also baked the plates in hydrogen to increase their light sensitivity)

Re:First commercial curved CMOS sensor from startup CURVE by BostonEnginerd on Sunday December 20, 2020 @07:51PM (#25491038)
Everything old is new again!

We may be back to vacuum tubes again soon:

https://spectrum.ieee.org/semiconductors/devices/introducing...

Re:First commercial curved CMOS sensor from startup CURVE by Vrondi on Tuesday December 15, 2020 @03:50PM (#25435073)
This is from a reply they made to a comment on the article: "Hi, you are right, we take available sensors and just change their shape before packaging. It makes it a plug-and play product, with no need to have a specific PCB development."
Re:First commercial curved CMOS sensor from startup CURVE by arthurcolle on Tuesday December 15, 2020 @04:58PM (#25435759)
Sorry, I’m a pleb but in what capacity/setting is this particularly useful?

EDIT: I don’t mean this in a negative manner, I just don’t know about this kind of stuff so I’m curious about what settings this is useful.

Re:First commercial curved CMOS sensor from startup CURVE by signaru on Tuesday December 15, 2020 @07:54PM (#25437631)
As someone who have designed lenses (with Zemax et al), this means I can get by with fewer lens elements, making it less expensive. That's one aberration type I can stop worrying about.
Re:First commercial curved CMOS sensor from startup CURVE by Judgmentality on Tuesday December 15, 2020 @05:05PM (#25435827)
https://en.wikipedia.org/wiki/Petzval_field_curvature

A curved sensor should improve optics by limiting distortion. So basically it can take better pictures.

Re:First commercial curved CMOS sensor from startup CURVE by arthurcolle on Tuesday December 15, 2020 @05:25PM (#25436067)
Thanks, appreciate it. Kind of like an eyeball?
Re:First commercial curved CMOS sensor from startup CURVE by sudosysgen on Tuesday December 15, 2020 @10:30PM (#25438717)
Pretty much, yes. Sometimes it will have the opposite curvature.
Re:First commercial curved CMOS sensor from startup CURVE by arthurcolle on Tuesday December 15, 2020 @05:47PM (#25436358)
the other guy deleted his reply :( I liked the added information
Re:First commercial curved CMOS sensor from startup CURVE by ohazi on Tuesday December 15, 2020 @06:10PM (#25436652)
One interesting challenge I assume they faced here is that the properties of Silicon that are relevant for transistors can be (significantly?) affected by stress/strain.

So while it seems reasonable that you could thin down a digital circuit and have it continue to function correctly when bent, a CMOS sensor is a very analog device. I wonder if noise / dark current / other properties vary depending on where the stresses are applied.

Re:First commercial curved CMOS sensor from startup CURVE by bgee on Tuesday December 15, 2020 @08:41PM (#25438009)
How would this sensor works with the microlens [0] that help direct the lights onto each pixel and already exist in most modern camera CMOS?

[0]: https://en.wikipedia.org/wiki/Microlens