Is it really? I've looked into this a good bit myself and it seems that many who have tried this have trouble keeping the diameter consistent.
I suspect that if it really was trivial, then you'd think just about any commercial supplier could get it right, there's a lot of junk filament out there. Maybe you are just very good at it; +-0.02 is pretty good even by commercial standards. The entire first page of Amazon best sellers are +-0.03 or +-0.05.
If you'll check my medium post, I've linked a video where I am extruding filament.
Problem with those hobbyist machines is motor torque/power rating. And second, they don't use a special screw and barrel.
The motor used in professional extruders used in real filament factories starts at 5 horsepower for the smallest machine.
If you miss those two things, there is no way you'll get within 0.03mm
Without any PID feedback loop, I can get within 0.03 by setting puller speed manually.
>I suspect that if it really was trivial, then you'd think just about any commercial supplier could get it right
There is no reason to believe that junk filament is coming from people with good machine design. That could be coming from hobbyist underpowered extruder machines like filaestruder and likes.
>Maybe you are just very good at it; +-0.02 is pretty good even by commercial standards. The entire first page of Amazon best sellers are +-0.03 or +-0.05.
At higher extrusion speed you'll get more output per extruder machine time but you'll have lower filament dimensional stability.
So the trivial part is have a powerful motor, use a good screw+barrel and don't extrude too fast.
That said I've offered my telegram in medium post and YouTube video. So anyone who gets stuck can reach out to me. I am not leaving them hanging on their own.
Also, I am looking to make a microcontroller firmware for extruders which basically measures the filament then sets the puller roller speed based on thickness measured. It pulls filament faster if it's thicker than target and pulls filament slower if filament is coming out to be thinner than expected. This will help us reach 0.0020mm accuracy easily!
The problem I am facing is:
1. I am not good with micro controller and control algorithms
2. Laser guage which measure the filament without distorting it is expensive and starts at 2K USD.
So anyone who can help solve these technical challenges are welcome.
But you might not need this much dimensionally accurate filament. Selling within 0.03mm is easy.
Anything better not sure how much it will help FDM quality but yes microcontroller firmware approach will help get more output out of this machine as biggest problem with extruding too fast is that dimensional stability goes haywire.
At some point dust in the air will be a limiting factor.
1: https://pdf.sciencedirectassets.com/274145/1-s2.0-S175161611...
Though your idea of a light source and adc could work well if you put it in a darkened enclosure. It’d probably require a bit more hardware design or tuning but the software / microcontroller side would b simpler. A RPi PiCam with a macro lens would work well too, but the reverse with less hardware tweaking and more software.
As long as your material is consistent (no bubbles, shiny spots, etc.), You should be able to build a very accurate sensor this way.
They use a laser pointer to measure width of a hair.
There is a shortage of Extruders because of the people making 3D printing filament at home. So I've been creating Extruders and selling them.
:-)
https://www.noztek.com/product/noztek-xcalibur/
The 13k listed machine produces 2kg per hour.
Extruder are heavy and low demand item, even cost of shipping will double the price of the machine which I've made.
As the saying goes "talent is evenly distributed; opportunity is not."
I've known lots of very smart people working what would be considered dead-end, or at least, lower-end jobs.
But usually they need a visionary who can make them believe in the idea and then they can put their work/efforts/mind into it with confidence and they do end up achieving the result at the end.
Call center -> building machines from scratch based on a medium post.
Sure it’s possible but I don’t think the suggestion really makes sense. You can be blind to the fact that hn is in the 1% of intellect/ability, but it should be obvious that effectively no one can honestly take that suggestion. Unemployed, low on cash, and then in a low-skill industry it doesn’t make sense to risk $500 to $1000 on a project that you likely won’t be able to build.
In a past life I worked at a place where my manager & IT guy were originally call center workers. The manager was a crafty guy, does nice woodwork. My ex happened to also work at that call center & is now an illustrator. Another friend from that place eventually went to college to be a machinist
I understand it's a pretty straightforward way to look for common ground and introductory topic of conversation, but there's a massive implication which I consider socially corrosive.
It is socially corrosive because it is removes any concept of social relationship from the calculus of social worth.
And you see this in the discussion of "opening up the economy" as though that is the #1 parameter of existence. Certainly without a functioning economy there is no food or other basic needs, but the objectives are complex functions, not simplistic ones. The implication is that those who were not lucky enough to have a job that generates income during a time of pandemic must needs put themselves at risk while others need not. Disgraceful.
It's the same reason I cringe when people talk or write about "consuming content", as if "content" is fungible and that peoples' roles are to "consume" it -- when information is not "consumed" (destroyed) by being enjoyed.
I don't see how that follows from "What do you do?" because one could answer:
A) I volunteer at... B) I take care of... C) I love... D) etc.
Cost is the bigger concern, but at 600-700 $, it's hardly mind-numbing.
https://medium.com/endless-filament/make-your-filament-at-ho...
This activity also help recycle waste plastic.
Production cost of filament is $7.5 per 5kg and filament roll has 850 gram filament and can be sold for $20-30 per spool
It's trivial to get the quality right.
You can sell rolls on Amazon, eBay and Etsy or your own Shopify store and use Facebook ads/Google Ads to advertise your website.