Can you name one voltage regulator that has them? Maybe you've worked with a few, but just off the top of my head, the 78xx, 317, and 1117 don't, and neither do all the other miscellaneous ones that I've seen in consumer electronics.
It's not my field and I had little clue what was happening at the EE level. Maybe you could argue they are not what is normally meant by saying voltage regulators.
In general I agree with the GP look at how many unpopulated areas exist on modern boards.
How should you know if the lack of input filtering is because of poor design vs the fact that the spec of the power supply changed and you no longer need it?
If it’s not universally true and obvious it’s not a good test.
Modern boards are super complex I’m not an EE but I would more likely flag lacking probe points, probe points which are too far or too close apart or too far from common ground as bad design choices than try to figure out if there are enough caps for the voltage regulator without knowing the full specs of the damn thing.
For all i know that voltage regulator isn’t even being used anymore because the IC or PSU specs have changed mid production but because it was wave soldered with a different soldering method than the other SMTs they already had them on a bunch of boards...
If you can’t reverse engineer the board or the relevant within a few min it shouldn’t be in an interview.
Not an EE but I do a lot of HW RE if anyone puts a modern multi layer doubled sided board on my lap and tells me to point out what’s wrong with it in an interview I would ask them what’s wrong with them.
That's exactly what everyone says when candidates fail FizzBuzz.
The best explanation I know is that good candidates get hired quickly, so at any given moment, the candidate pool is dominated by people who keep failing questions like this.
- Stress-levels of the candidate - Tone / demeanor of interviewer - Communication prior to interview
I mean, sure, if you fail fizzbuzz interviews 10 times in a row, there seems to be some pattern going. But you could might as well fail it the first time, and get blackballed as incompetent.
It would be great if they'd stumble over conundrums like "what if there are non-numeric entries in the array." Most often, they just stare and don't even start on the problem.
Are you expecting some map-reduce-like parallel sum, or something else?
If the role's primary function is to do validation prior to manufacture this seems like reasonable. it assumes that new circuits will have some number of fairly common mistakes. in my experience this is very true, despite the skill of the engineer who designed the circuit. missing termination, pullup/downs missing, etc. if the role is applications engineering...well...its far less likely you would be troubleshooting common circuit design issues so much as you would be troubleshooting common system design issues. im sure you can extend this to other functional roles an EE may take on. if the job is to design a MCC and size breakers to minimize arc flash hazards i doubt the applicant will be up on a correctly build half-bridge rectifier.
in that list quoted i've encountered all of it in new designs, including missing stuff plainly stated in the part's application notes (like those regulator caps).
This is different than for bulk capacitors, but even those should still be on the same PCB assembly because connectors have higher resistance and this will limit their ability to handle transient surges.
Not all LDOs are stable without external output capacitance in a particular range / ESR.
Understanding that the capacitor and the trace form an RC circuit and that distance matters is what separates a professional from a beginner.
I would still argue that logic IC have alot of internal pull ups. Or that eg. "Reset sequence of digital component is wrong" is a bad whiteboard question.
Otherwise the person may just ask: "where are caps, or is this thing a module or what?"
Definitely not a switcher or module, could be an LDO.
They're useful if the voltage drop isn't too large and/or if you need a particularly stable output voltage; contrast them with switching regulators, which are more efficient but have some amount of output ripple.
One design that I worked on used a switching regulator to generate 5V, then linear regulators to generate something like 3.7V and 2.9V for various sensitive analog circuits.
Examples he gives:
"Current limiting resistors missing (BJTs, diodes, etc.)
Shorting a potentiometer node to a rail
Voltage regulators missing capacitors at input/output
Missing pull-up/pull-down resistors on digital buses
Missing decoupling capacitors"
I mean ... looking at a schematic how should you know that the voltage regulator doesn't have internal caps without seeing the specs? Missing pullups? How do you know those are not internal? It is stupid.