I see it more as a single big massively wide OoO core with 23 execution units (putting skylake's 10 execution units to shame). The slices are more there for design reasons, to simplify the design process by making it more symmetrical.
Bulldozer is clearly two integer cores sharing some execution units between them, a thread can only exist on one of the two integer units.
In contrast, a thread on POWER9 can simultaneously use all 4 slices, all 23 execution units. The dispatcher can dynamically mix and match which slice it's sending a threads instruction steam to based on slice utilization.
That single difference puts it in a complete different class of CPU architecture to bulldozer.
My reading of the documentation is different.
> The most significant partitioning related to threads occurs when more than two threads are active, placing the core in SMT4 mode. In SMT4 mode, the decode/dispatch pipeline, shown in the blue shaded area in Figure 25-1 on page 321, is split into two pipelines, each pipeline is three iops wide and each pipeline serves two threads. The split decode/dispatch pipes each feed one of the two superslices, shown in the green shaded box in Figure 25-1, providing two execution slices for each pair of threads. The branch slice and LS-slices are shared between all threads.
Page 322 of 496: https://ibm.ent.box.com/s/8uj02ysel62meji4voujw29wwkhsz6a4
-------
The left superslices serves 2-threads, while the right superslice serves 2-threads. All 4 threads are "behind" the singular decoder.
It seems very "Bulldozer-esque" to me, especially in SMT4 mode.
---------
You are correct in that there is an SMT1 mode where one-thread could potentially utilize the entire processor. But with 2-latency on even Add / XOR instructions (see Appendix A), I don't foresee SMT1 code to be very useful on Power9. The processor is clearly designed to run most effectively on SMT2 or SMT4 modes.
I'm not even sure how easy or hard it is to switch into SMT1 to SMT2 or SMT4 modes. I don't think Linux can switch cores while running, and may need to reboot for instance. Maybe AIX can switch between the modes on the fly?
I guess if your code has enough Instruction Level Parallelism (ILP) available in its code stream, it could benefit from SMT1 mode. But I'd imagine that most 64-bit CPU-code wouldn't have much ILP.
It's only in SMT4 mode that it starts statically partitioning the threads onto superslices. Even then, it's two threads sharing two slices.
I assume the static patitioning is an optimisation, that preformance increases due to the split L1d caches (and I'm guessing there is a delay cycle when one slice depends on data from another, I haven't read the documentation that closely).
It's the fact that slices can be dynamically scheduled across all four slices which makes it "not bulldozer" in my mind, and I don't think the presence of a mode that does statically partition superslices should make it "like bulldozer", even if that is the most common mode. It's just an optimisation.
> I'm not even sure how easy or hard it is to switch into SMT1 to SMT2 or SMT4 modes.
Idealy, the CPU core would dynamically drop down to SMT1 or SMT2 mode whenever the the extra threads are executing idle instruction.
Well, its certainly a Bulldozer-like mode of operation :-)
Power9 is obviously a very different chip than Bulldozer. So I guess it all comes down to opinion, whether or not the chip is similar enough to warrant a comparison.
I believe 7nm POWER10 will be the next move, they had announced Samsung as the partner for their next chips back in December if I remember right.
The Power9 18-core / 72-thread is going to come in at under 150W total.
The main advancement the past decade has been in power-efficiency. Cloud-scale providers keep their computers running at max load as well, so 500W does add up over months / years into a sizable amount of money.
Especially when you consider that 500W computer needs 500W of Air-conditioning, so the "True cost" of a 500W computer is roughly ~1200W or so (500W from the computer, 700W to power an air-conditioner to move 500W of heat)
----------
A 12-core / 24-thread AMD Ryzen 3900x is just $500, with a total system cost under $1500. The big advantage of a Ryzen 3900x would be a max clock-rate of 4.7 GHz, while your Nehelem 2009 computer is... what? 2.5 GHz? Probably? And computers of that age didn't have deep sleep capabilities, wasting even more power than usual. Modern computers idle at 20W, even servers and desktops. Tons of power-saving features these days which add up.
I think a typical $1500 computer these days would be more than twice as fast with 1/4th the power usage. I don't think anybody seriously in this hobby should be using anything as old as Nehelem these days.
IMO, the price/performance "old computers" seems to be Haswell (~2014 era servers), if people want to buy old equipment. But 2009 is definitely too old, there are lots of used servers that are a little bit more expensive but a LOT more power efficient / faster in practice.
I thought air conditioners/heat pumps were supposed to be substantially better than 1w of heat moved outside per watt of electricity?
15 BTU/hr == 5 Watts of cooling per Watt of input.
So it appears you are correct. To move 500W watts of heat, you only need 100W of air conditioner power.
For example, the Dell PowerEdge R630 (2014-era) server is in and around $600 to $1000 on Ebay, and will be more power-efficient and faster than any 2009-era system.
I think 2014-era servers are where the price/performance point is for the home-server enthusiast, especially if we're talking about sub $1000 price points.
https://www.ebay.com/itm/Dell-Poweredge-R630-2x-Xeon-E5-2640...
2x8 core dual socket Intel Xeon E2640 v3 (Haswell) with 64GB of RAM. Its an auction, so it will probably go up another $100 or $200 from there, but I would expect it to sell well south of $1000.
2014-era equipment is the current price/performance king for home hobbyists. Obviously, a modern desktop with all the bells and whistles is a bit more expensive at $1500, but for $6oo to $700, you can get a pretty good 2014-era system.
-------
My rule of thumb is to buy something 5-years out of date. That's roughly the time when businesses get rid of old equipment and upgrade. So 5-years old equipment tends to win in price/performance.
Well, I guess the Mac Pro is fine for that, as long as you're fine with the Mac OSX operating system. The Mac Pro line hasn't really had many updates, so maybe the 5-year heuristic doesn't really apply.
The TDP on the 18 core (and 22 core as well) is 190W as listed on Raptor’s website.
But only 1x divider, 1x crypto unit per SMT4 core.
The chief downside to Power9 is that it only supports 128-bit vectors, and these 128-bit vectors are executed by ganging-together the ALU units. (so 4x 64-bit ALUs == 2x 128-bit vectors processed per clock tick). Compared to AMD Zen (4x 128-bit pipelines), AMD Zen 2 (4x 256-bit pipelines), and Intel Skylake-X (3x 512-bit pipelines), Power9's SIMD capabilities are tiny.
Another oddity: most instructions take 2-clock ticks to execute, even simple instructions like XOR or Add. This increased latency is likely the reason why it performs so poorly with Python / PHP code.
But when code is written for Power9, it works quite well. Stockfish chess seems to work extremely well on Power9, likely because Stockfish scales to many "cores" well (fully taking advantage of SMT4), and only has 64-bit operations.
One more wildcard: Power9 has 10MB (!!!) L3 cache for every 2-cores. That's 90MB L3 cache on the 18-core. I presume that real-life database applications would benefit greatly from this oversized L3 cache.
EDIT: It should be noted that the L3 caches serve as victim-caches of other L3 caches. So Power9 core-pair 01 can have its 10MB L3 cache serve as a "L3.1 cache" of core-pair 23. AMD Zen / Zen2 L3 cache CANNOT use this functionality. So AMD Zen2 64-core may have 128MB of L3 cache, but each core only "really" can go up to 16MB of L3 cache (because the other 112MB of L3 cache is only for other cores/module)
EDIT: Also note, Power9 came out a few years ago at 14nm, while Zen2 came out on the 7nm node a month ago. I think a new 7nm Power9 update is planned, but I don't know what its timeframe is.
In effect, you could have 1-program using the entire 90MB L3 cache for itself on Power9. While AMD Zen2 requires (at minimum) 8-programs, each program using only 16MB L3. This design decision is clear in the intended use of the chips: Zen2 is clearly targeted at the cloud-market, while Power9 is big-iron / databases.
--------
Unfortunately, most of the benchmarks these days show that AMD EPYC / Rome is just the better overall processor. Still, 18-core Power9 is relatively cheap: a complete 18-core / 72-thread system for $4000ish: https://secure.raptorcs.com/content/TLSDS3/purchase.html
Cheap for Power9 anyway. AMD EPYC is also relatively cheap. You can get a 16-core / 32-thread / 32MB L3 cache AMD Ryzen 9 3950x for only $700 these days (and maybe a complete system build for only $2500).