Re:Cartoons in Tektronix Schematics
by pjc50 on Friday August 02, 2019 @11:29AM
(#20593743)
The magnum opus of Jim Williams known as "App Note 47" has a cartoon at the end, and possibly a few more in the middle. As well as a copy of "Murphy's Law".
The cartoons in schematics are very much a product of their time - they were hand-drawn by skilled draftsmen who enjoyed drawing. I suspect most of them had a spare pad of doodles next to their work table.
Re:Cartoons in Tektronix Schematics
by blattimwind on Friday August 02, 2019 @11:43AM
(#20593870)
They also attempted to make schematics logically cohesive, if possible. For example, in oscilloscopes signal paths are typically differential and DC coupled, but there are often sections where high and low bandwidth components are fed through different paths. In Tektronix schematics these symmetries and asymmetries, which paths are critical and which aren't, which things may look symmetric but are not, these are all very visible. This isn't always possible, though. For example, the Z blanking signalling in 7000 series scopes is distributed over approximately six or seven circuit boards just in the main frame, and the schematic drawers clearly came to their limits trying to pull this together into cohesiveness.
If you compare this to the schematics of more modern electronics, they are often madness. Even though it is far simpler to re-arrange schematics using EDA, it clearly isn't done a lot, because parts are sprinkled around randomly, everything is just on one enormous sheet or everything is randomly split up across sheets with numbered net names making connections etc.
Re:Cartoons in Tektronix Schematics
by cyanoacry on Friday August 02, 2019 @12:54PM
(#20594456)
As someone who's worked on (and drafted!) several schematics in the aerospace industry, I have to say: there's no reason it has to be that way!
The places I've worked have pretty rigorous style guides, and I personally try my best to make schematics readable and understandable. I suppose this is the same thing as code quality guidelines: you can set expectations and examples, but folks don't necessarily have to follow them.
Re:Cartoons in Tektronix Schematics
by blattimwind on Friday August 02, 2019 @05:26PM
(#20596801)
Some critique
- psu drawing: no left-to-right flow, connector names are numbered, output connector (CONN2) is just floating around on the left and connected via net names. Same pretty generic net name ("out") is used as in the main amp.
- amplifier drawing: the main feedback loop is obscured because it's only connected via net names, connectors are again just stashed of somewhere to the side and only connected by name and not labelled. I would also point out that each op-amp of the quad-op-amp U1 shares the same designator, so you can't talk about U1a, U1b etc., which you actually do in the text.
The left half of the schematic is arranged pretty neatly and logically, but the discrete output stage is pretty cramped over there (clearly limited by the fixed sheet size), though standard arrangements of the building blocks make it quite clear what everything is (U1c U/I conversion, current mirror to the top rail, mirrored back to the bottom rail with an x3 CM, resistive load to the top, emitter follower output stage, CCS as load, off to the output).
Re:Cartoons in Tektronix Schematics
by cyanoacry on Friday August 02, 2019 @04:31PM
(#20596371)
Maybe! I've worked with some SiC FETs, but the issue I ran into with FETs in amplifiers is that they're typically made with switching in mind. If you run most FETs in linear mode, you get some pretty interesting failure modes[1].
But, Wolfspeed's SiCFETs /do/ have a published SOA (see fig 22[2]), so maybe I should revisit this...
[1] Figure II-3: "Visual Image of the IRF1405Z failure. This type of visual pattern is more attractive when observed on the surface of the moon, instead of on the surface of parts that are trying to land there." http://www.irf.com/technical-info/appnotes/an-1155.pdf
Re:Cartoons in Tektronix Schematics
by aidenn0 on Friday August 02, 2019 @07:23PM
(#20597505)
Even FETs that have a published SOA, it often ends up being roughly "don't spend more than about 10% duty cycle in the linear region" because FETs have been so strongly optimized for switching applications.
Re:Cartoons in Tektronix Schematics
by minikites on Friday August 02, 2019 @10:57AM
(#20593453)
I used to like easter eggs in software but as the security landscape has changed, easter eggs now show a lack of oversight. If a programmer can slip in an easter egg, what else can they slip in?
Re:Cartoons in Tektronix Schematics
by trhway on Friday August 02, 2019 @04:01PM
(#20596115)
>easter eggs now show a lack of oversight
no. Easter eggs show lack of "zero tolerance" corporate posturing. Which isnt to say that such posturing isnt important part of the security theater.
The cartoons, easter eggs, etc. is a "human touch", a sign that the product is done by people who love (or at least feeling something toward) their job, not by drones. Modern corporate environment is based on droning and has naturally extinguished that human culture.
Re:Cartoons in Tektronix Schematics
by CamperBob2 on Friday August 02, 2019 @01:18PM
(#20594718)
If you don't have the source code, you can't "trust what's on your computer," as Osterman puts it. Easter eggs have no impact on that axiom one way or the other.
So, coming from Microsoft, it's easy to dismiss the entire article based on its initial premises.
Re:Cartoons in Tektronix Schematics
by ryandrake on Friday August 02, 2019 @03:23PM
(#20595813)
If they are documented, as a user I would still think, "What else could they have been improving/fixing if they weren't working on easter eggs?" I wonder if in an alternate world, Excel minus the flight simulator easter egg could have been $1 cheaper or had 5 more bugs fixed.
Re:Cartoons in Tektronix Schematics
by makapuf on Friday August 02, 2019 @04:23PM
(#20596291)
As a dev, I can relate to working overtime for a small eater egg, or even if I were a manager I could understand those (security implications notwithstanding) if it would boost morale or team cohesion better than an akward social event.
Re:Cartoons in Tektronix Schematics
by LocalH on Friday August 02, 2019 @06:12PM
(#20597060)
That's an amazingly entitled viewpoint, in my opinion. There's also a rabbit hole there of saying that about any feature that one doesn't make use of.
I understand the concept that maybe certain classes of software (say, medical or military software) shouldn't have eggs, or perhaps that certified eggless versions of software should be available in situations involving contracted software. But would you say the same thing about game software? Hobbyist software? Easter eggs aren't always bad.
Re:Cartoons in Tektronix Schematics
by WalterBright on Friday August 02, 2019 @04:32PM
(#20596381)
I like a bit of whimsy in otherwise dry stuff. We try to enliven the D language spec with a D-Man cartoon here and there. I'd do more if I had any talent for drawing.
Re:Cartoons in Tektronix Schematics
by moftz on Friday August 02, 2019 @09:45AM
(#20592834)
I love finding easter eggs in die layouts. Even if it's not an easter egg but just someone's name, it's always nice to see how people have chosen to essentially scratch their name into history.
Re:Cartoons in Tektronix Schematics
by microDude on Friday August 02, 2019 @09:52AM
(#20592890)
To my surprise there is a museum right down the street from my house (Beaverton/Portland, OR USA). That I must have just been missing. Thanks for posting!
Re:Cartoons in Tektronix Schematics
by segfaultbuserr on Friday August 02, 2019 @10:31PM
(#20598278)
Glad to see my post brings a nice trip to you.
From the comment sections, it appears to me that Hacker News has no shortage of hobbyists and professional electronics engineers, but when I search relevant terms like "Tektronix", "oscilloscope", "spectrum analyzer", or "SPICE", there's no much information here, only two or three top articles. I guess it's unfamiliar to the Silicon Valley CS majority who doesn't have enough appreciate of hardware engineering. I'll try to post more of them in the future.
Re:Cartoons in Tektronix Schematics
by gaze on Friday August 02, 2019 @10:02AM
(#20592974)
Absolutely go. I repair these scopes as a hobby and the people at the tek museum have been endlessly helpful. Repairing old tek designs and reading the schematics has made me a much better analog engineer.
Re:Cartoons in Tektronix Schematics
by pjungwir on Friday August 02, 2019 @11:14AM
(#20593593)
Hey I'm in Cedar Mill and used to live practically across the street from Tektronix. My email is in my profile if you want to get coffee or check out the museum together. :-)
Re:Cartoons in Tektronix Schematics
by TheOtherHobbes on Friday August 02, 2019 @04:14PM
(#20596207)
Somewhat distantly related - the Pro One synthesizer from the early 1980s had some "appropriate" graphics silkscreened on the PCB and the copper etch. A list and photos here:
Re:Cartoons in Tektronix Schematics
by segfaultbuserr on Friday August 02, 2019 @09:30PM
(#20598046)
I wonder if cartoons like these (a distinct form of cartoons, unlike Tektronix) is a feature in Japanese media communication culture. I've seen similar comics of this style in Hakko's soldering 101 marketing materials [0], factsheets of Panasonic's solid aluminum capacitors, and user guides of Japanese laptops like Toshiba and Sony.
Hikaru's diary on learning to solder. A short story about soldering, from basic tools and safety precautions for getting started to solder things, good and bad solder joints, and the purpose of flux, it later goes on to explain how simple and thermal-regulated irons and how their heating elements work, point soldering and drag soldering techniques for SMD components, wave soldering and reflow soldering, and finally SnPb and lead-free alloy.
Re:Cartoons in Tektronix Schematics
by chrisdhoover on Friday August 02, 2019 @10:33AM
(#20593253)
Back at the hi fi shop in the mid ‘70’s my older brother came over to my bench with a big smile to show me an amplifier schematic with a race car drawn on the arrow indicating an output.
We were simple people then finding amusement in the smallest things
Re:Cartoons in Tektronix Schematics
by raintrees on Friday August 02, 2019 @11:44AM
(#20593875)
I miss my old Tektronix Oscilloscope... I was learning electronics, a whole new world opened up. That was a great feeling, probably why I keep learning new software languages.
The cartoons in schematics are very much a product of their time - they were hand-drawn by skilled draftsmen who enjoyed drawing. I suspect most of them had a spare pad of doodles next to their work table.
If you compare this to the schematics of more modern electronics, they are often madness. Even though it is far simpler to re-arrange schematics using EDA, it clearly isn't done a lot, because parts are sprinkled around randomly, everything is just on one enormous sheet or everything is randomly split up across sheets with numbered net names making connections etc.
The places I've worked have pretty rigorous style guides, and I personally try my best to make schematics readable and understandable. I suppose this is the same thing as code quality guidelines: you can set expectations and examples, but folks don't necessarily have to follow them.
My cooler projects are all stashed away somewhere in a company drawer, but here's one that I did early on: https://bitbucket.org/cyanoacry/ee91/raw/5d934fdc18e556938dc...
- psu drawing: no left-to-right flow, connector names are numbered, output connector (CONN2) is just floating around on the left and connected via net names. Same pretty generic net name ("out") is used as in the main amp.
- amplifier drawing: the main feedback loop is obscured because it's only connected via net names, connectors are again just stashed of somewhere to the side and only connected by name and not labelled. I would also point out that each op-amp of the quad-op-amp U1 shares the same designator, so you can't talk about U1a, U1b etc., which you actually do in the text.
The left half of the schematic is arranged pretty neatly and logically, but the discrete output stage is pretty cramped over there (clearly limited by the fixed sheet size), though standard arrangements of the building blocks make it quite clear what everything is (U1c U/I conversion, current mirror to the top rail, mirrored back to the bottom rail with an x3 CM, resistive load to the top, emitter follower output stage, CCS as load, off to the output).
But, Wolfspeed's SiCFETs /do/ have a published SOA (see fig 22[2]), so maybe I should revisit this...
[1] Figure II-3: "Visual Image of the IRF1405Z failure. This type of visual pattern is more attractive when observed on the surface of the moon, instead of on the surface of parts that are trying to land there." http://www.irf.com/technical-info/appnotes/an-1155.pdf
[2] https://www.wolfspeed.com/downloads/dl/file/id/145/product/1...
1. We can ensure that they won’t explode when we use them.
(admittedly I understood very little after that ;P)
Wikipedia has a list of software easter eggs, let's see if we'll discover more of them as time goes on.
Larry Osterman says it even better: https://blogs.msdn.microsoft.com/larryosterman/2005/10/21/wh...
no. Easter eggs show lack of "zero tolerance" corporate posturing. Which isnt to say that such posturing isnt important part of the security theater.
The cartoons, easter eggs, etc. is a "human touch", a sign that the product is done by people who love (or at least feeling something toward) their job, not by drones. Modern corporate environment is based on droning and has naturally extinguished that human culture.
So, coming from Microsoft, it's easy to dismiss the entire article based on its initial premises.
[edit]
For those less familiar, feel free to browse adequacy.org, or just read this gem:
http://www.adequacy.org/public/stories/2001.12.2.42056.2147....
I understand the concept that maybe certain classes of software (say, medical or military software) shouldn't have eggs, or perhaps that certified eggless versions of software should be available in situations involving contracted software. But would you say the same thing about game software? Hobbyist software? Easter eggs aren't always bad.
if anything, i think that Excel would have much more bugs, and would have much tougher time taking off :)
Scratch that.
Evil usually comes from above.
That was an eons ago different era.
https://i.imgur.com/jYNCC4d.jpg
https://dlang.org/spec/iasm.html
Go's gopher cartoons are a nice touch, too.
etch their name into history ;-)
From the comment sections, it appears to me that Hacker News has no shortage of hobbyists and professional electronics engineers, but when I search relevant terms like "Tektronix", "oscilloscope", "spectrum analyzer", or "SPICE", there's no much information here, only two or three top articles. I guess it's unfamiliar to the Silicon Valley CS majority who doesn't have enough appreciate of hardware engineering. I'll try to post more of them in the future.
https://jamebus.backpackit.com/pub/294552
https://www.global.tdk.com/news_center/publications/power_el...
[0] https://www.hakko.com/english/hikaru/pages/
Hikaru's diary on learning to solder. A short story about soldering, from basic tools and safety precautions for getting started to solder things, good and bad solder joints, and the purpose of flux, it later goes on to explain how simple and thermal-regulated irons and how their heating elements work, point soldering and drag soldering techniques for SMD components, wave soldering and reflow soldering, and finally SnPb and lead-free alloy.
We were simple people then finding amusement in the smallest things