I've not tried one and at around $75 they aren't cheap. I was looking into them at a time when my cable modem would forget how to route anything and need to be power cycled, but replacing it did the trick.
And here's one that resets based on a timer rather than Wifi signal: http://www.netreset.com/
And another one that uses ethernet: https://www.amazon.com/3Gstore-Remote-Power-IP-Switch/dp/B01...
ResetPlug is for WiFi, but hasn't posted anything since 2016 (I'm a bit worried that it might not exist any more).
Megatec ezPower is in Taiwan (local for me), but is only Ethernet. Often the Ethernet still works even when the WiFi doesn't, so I'll try to get the ResetPlug first.
While I wouldn't add another router, I've found that adding additional AP's almost always makes things better, assuming they are not on overlapping channels.
If you have malfunctioning hardware, then you're going to have problems whether you have one AP or multiple AP's -- use better hardware.
I've often speculated that the temperature is causing problems, which would also explain why it's hard to reproduce the issue when a telecom service tech comes over. I'll have a look around for a suitable fan, and see if that helps.
Why not use Powerline Ethernet? In most houses, it's typically fast and reliable and requires no extra wires. E.g. the data rate between my desk and router is currently 784 Mbit/s.
Cheap ones suffer from the same problems as cheap routers, randomly hanging and requiring a physical plug / unplug when the room gets hot, or whatever other interferences degrade their performance over time.
Expensive ones are still not 100% reliable, and most of the time will cost more than a well done ethernet installation.
Of course, as a sibling said, it'll depend a lot on the wiring and/or other connected devices. So I guess it's best to try with a borrowed pair of adapters first.
Also, avoid TP-Link adapters as they seem to have some issue coming out of powersave mode that means I have to ping something all day to prevent them from sleeping
I'm renting the house, and wherever I move next probably won't have this problem.
In the UK I have had very few problems with powerline one failed through over heating and had an issue when we had our solar panels installed as the POS Netgear router didn't implement STP and we had a broadcast storm
Good idea about automation, I try it at home.
Would some of those 'homeplug' plugs that use the mains wiring as a closed circuit low frequency radio signal link be tidier? I used a fairly low speed pair to get Internet from modem/router downstairs to desktop PC upstairs without drilling holes and running cable. Worked ok.
2. Adding an additional router almost always makes things worse.
Solution: Switch off nodes when they stop working.
My house has this problem. I live on the 4th floor, next to the main VDSL router. The kitchen & living room on the 2nd floor can't get a strong WiFi signal. After some thought about WiFi repeaters, I decided to buy a long Ethernet wire and run it down the stairs. I trip over it sometimes, but it's basically reliable. The downstairs router runs dd-wrt, and works fine 99% of the time (I've had to reboot it once in the past year).
The upstairs VDSL router is owned by the telecom company (Chunghwa), and they don't give me administrator access. I can't change the firmware, and the box is frankly awful. About 6 months ago we complained repeatedly, asking them to replace the box. They sent tech guys, who tested the wire, and said that everything is fine. Indeed, it works about 70% of the time. But very often I come home from work, and I have to reboot that router before I can get online.
My solution is to buy a Edimax WiFi power socket and a Raspberry Pi, which checks to see if it's online. When the network goes down for more than a minute, it'll automatically tell the WiFi power socket to turn the router off and on again.
I know that power-cycling is bad for the router, but I don't see any other solution given the software constraints. I'm also surprised that there are no companies making devices for the purpose of power-cycling routers.