> The size of the smallest particle was 160 μm and the largest sized 980 μm.
This was shocking to me, that they could miss a millimetre-scale particle of plastic in salt seems bonkers. I mean, you can more or less just filter things that size!
You can filter them - and they certainly do - but with sea and lake salts the filtration is mainly to screen out sediments such as sand grains and bits of shell. Naturally, the filtering is a costly process and the filters need to be discarded after a certain level - I imagine there is a cost-control factor here, where screening at a 1mm threshold catches 99.9% of sediments to make the product reach a certain purity level and more thresholds are not worth the money.
Further screening is probably not cost effective - and seeing from the results of the study, plastic microparticles are not a source of concern.
In the brewing industry we use Kieselguhr (perlite) filtration with filters like this: https://www.ryebeckltd.com/current-equipment/schenk-kieselgu.... These can sterile filter particles as small as 1 micron and are density-independent. These work by having a steel plate with fine slots upon which you deposit a coarse bed of filter material, and then you dose kieselguhr into the liquid flow passing through, and this gradually builds up on top of the coarse bed to create an ultrafine filter. The ultrafine filter increases in depth over time, and this prevents blinding (blocking) of the filter as filtered particulates accumulate. While used to remove yeast and other particulates in brewing to create "bright" beer, it can be applied to most liquid filtration problems, and at high flow rates (30000 litres/hr); and you can run multiple filters in parallel to further increase the flow rates. We also used kieselguhr in research labs for fine filtration--just add the powder to regular filter paper.
In practice this is based upon manual calculation and adjustment. In the place I worked, the filter room had two of these, each about 1.5 storeys high. It had a dedicated control room to operate, and the two operators would be continuously monitoring and adjusting the flow rates, dosing and other parameters to ensure efficient operation. When you have an unexpectedly dirty product or you muck up the calculations, the flow rates can become very low and that starts to cost serious amounts of money when it's a rate-limiting step in an industrial process.
When the filter becomes too inefficient, the backpressure excessively high, or the filter depth approaches the tank capacity, the metal filter plate is spun and this destroys the filter bed which is spun off. The coarse filter base is then reapplied to "regenerate" the filter.
> A total of 17 brands of salt from Australia, France, Iran, Japan, Malaysia, New Zealand, Portugal, and South Africa were purchased from a Malaysian market.
> Accordingly, it is expected that products originating from the contaminated water bodies are also loaded with MPs.
This sentence is the entire premise of the study. Testing non-waterbody-derived salts would not provide any valid data in pursuit of that hypothesis.
Furthermore the entire body of the abstract, introduction, and discussion discusses marine microparticles, impacts on aquatic health, and whatnot.
Salt derived from underground sources wouldn't be at risk of microplastics contamination.
Himalayan salt (found frequently in warehouse clubs) is a product of Pakistan and is produced >100 mi from the nearest portion of the Himalayas.
I still use and enjoy some on occasion.
A lot of the salt (~80%) produced in the US goes to road salt and chemical industries. For roads it's better if it's in rock form, so a lot (if not most) is mined. For chemical industry they can often re-use brining wells to hold other things later, so the great majority of chemical salt is brined.
Salt mines: https://en.wikipedia.org/wiki/Salt_mining
Of all the salt production methods, non-brine mined salts have the least toxic or harmful byproducts - at the source. But they still go through processing plants to sift, grind and package the salt, and not every processing plant has the same quality standards. If you wanted to get really picky about it you should choose a mined, non-brine, non-processed, non-refined salt produced at a facility that follows modern standards. The easiest to identify would be "himalayan" salt, but many countries have ancient lake/sea beds and mine and produce salt in the same way.
In general, you can't tell how salt was produced unless the company very explicitly tells you. Even kosher and sea salt sometimes is processed or refined with additives or in a way that could introduce MPs. (In case it helps, only some places like Australia and the mediterranean have the right environment to solar-evaporate sea salt at a commercial scale)
But I wonder how much salt is mined. Only one sample was plastic-free. But maybe it's mostly commingled. If one were really interested, one could look at plastic content vs Cl-36 (nuclear fallout) level.