News for hackers. Stuff that matters.
Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @10:17AM (#1231819)
My patience for the line, "It is digital. It either works or it doesn't" ended a long time ago.

"Digital" signals are analog signals, but the only difference is that they are restricted to being above or below some threshold. But around that threshold there is a gray area where you can't really tell whether your signal will be interpreted as 1 or 0.

I am not defending the need for high-end HDMI cables. But saying "It's digital so don't worry" is wrong.

There are reasons that "digital" cables use twisted pair. Wow, even some "digital" cable standards specify the number of twists per inch required for reliable operation. And wow, some cable standards even specify shielded cable is required. I wonder why.

Here is a fun exercise for those that think "digital" signals don't need engineering steps to protect signal integrity: build all of your cables (or PCBs for that matter) with straight signals and you will have an excellent time trying to debug why your communications don't work. Bonus fun for making the cable length 1/4 of your signal wavelength.

Re:Why you should never pay more than $10 for an HDMI cable ... by matwood on Wednesday March 31, 2010 @11:00AM (#1231930)
I think the point of the "either works or it doesn't" is a comparison versus analog. With an analog signal you could get slightly better results by getting better cables (or worse with worse cables). If you have a poor digital cable it flat out doesn't work. If the cable you're using works, buying a more expensive cable isn't going to make it work any better. Either the 1s and 0s made it from the source to the destination or they didn't.

No one is claiming that there isn't engineering that needs to happen to make a digital signal reliably travel from the source to the receiver.

Re:Why you should never pay more than $10 for an HDMI cable ... by ghshephard on Wednesday March 31, 2010 @11:55AM (#1232105)
Clearly you've never had an Ethernet Cable that got caught in a door. Or was terminated poorly. Or doesn't have the insulator sheath under the crimp. Or run parallel to a set of Florescent light ballasts. All of these events can reduce performance on Ethernet without causing it to fail outright.

There is a reason why every single TIA/EIA 568 cable plant is carefully tested for things like Near End Cross Talk (NEXT), Latency, Skew, etc..

There is also a reason why there is an entire _discipline_ dedicated to ensuring that the "Digital" signal not only has a channel, but a meticulously crafted one. (See: http://www.linktionary.com/t/tia_cabling.html for details)

To reiterates the OP - there is no "Digital Signal" - signals are analog in nature, and they need an analog channel to transmit them. That analog channel needs to be engineered carefully to get the lowest EBR (Error Bit Rate) possible.

What's interesting is the Failure case of the Digital CODEC on the other end - some may reduce transmit rate in the presence of an increased EBR resulting from dropped packets. Or some may seize up and cease to function. In the degraded case, having a pristine analog channel from the transmitter to the receiver will certainly result in a better digital signal.

There is also the issue of future proofing - We're installing an entire plant of Category 6a cable right now in one of our data centers for a gigabit environment - Category 6a is like the "Monster" version of Category 5e/6 - It seems like a douchey way to do a network install, except when you consider the following - (1) this cable plant will be in use for 10-15 years, (2) We're testing a bunch of Nexus 5010s that will likely make good use of that 6a for 10 Gigabit. So, in addition to passing _today's_ signal flawlessly, it will also pass tomorrow's. This might be an important factor if your HDMI cable is being run through hard to access cabinets/walls.

Now, with all that said, it is still probably the case that the $150 Monster Cables (under normal circumstances) don't have a lower EBR than a $10 cable, but, in the face of RF interference, It may actually be a better performer. I don't know, but I wouldn't discard the possibility without a bit of research and education.

Re:Why you should never pay more than $10 for an HDMI cable ... by pak on Wednesday March 31, 2010 @02:15PM (#1232585)
Anything running over Ethernet has packets with checksums. Yes, noise will cause packets to drop, and that results in lower overall throughput, while connectivity still remains possible.

The signal running over HDMI is not packet-based. You don't have any mechanism like with TCP where packets can get dropped and resent later. So if interference causes bits to flip on an HDMI connection, you will immediately see the interference on your TV, and it won't be pretty; it would probably look something like an HDTV antenna signal that loses reception--missing or discolored chunks of the screen or sparkly pixels. The effect is immediate and disruptive.

The end result is that Monster Cable might do a better job of keeping your picture intact during a freak electrical storm, but there is no practical difference otherwise. If you are able to see a picture with HDMI, and you don't expect any wildly varying levels of RF interference in your environment, your cable is as good as anything else.

Re:Why you should never pay more than $10 for an HDMI cable ... by tel on Wednesday March 31, 2010 @02:58PM (#1232713)
Again, nobody is disagreeing. This isn't a defense of Monster, it's a typical It's More Complicated Than That jibe. Don't buy Monster unless that flowchart checks out, but also realize that it's not impossible to see signal degradation on those cheaper digital cables.

It's just a lot less likely.

Re:Why you should never pay more than $10 for an HDMI cable ... by electromagnetic on Wednesday March 31, 2010 @05:29PM (#1233081)
A $10 cable should fail before a $250 cable, however the frequency of failures for an infrequently moved or manipulated cable should still give it a longevity of a few years.

A $10 cable wont fail 25 times within the lifespan of the technology it's attached to. HDMI won't exist before you get 25 failures, unless you enjoy hammering nails into you cables or some other bizarre behaviour.

Re:Why you should never pay more than $10 for an HDMI cable ... by rys on Thursday April 01, 2010 @12:05PM (#1234899)
I think most people will gladly pay more for a better cable, but they'd like to pay something comensurate to the engineering effort, and production and material costs. The markup is insane (nearly $200 apparently).

One has to wonder if Monster and their retail partners would make just as much money selling them at $50, due to higher volume, with the added bonus of people not totally misleading everyone with the value proposition.

Re:Why you should never pay more than $10 for an HDMI cable ... by electromagnetic on Friday April 02, 2010 @11:13AM (#1236613)
I spent about $5 more on my HDMI cables than I would have to get ones with a heavy-duty rubberised outside instead of the cheap and tacky bendy-plastic that breaks easily from over-manipulation.

You are right, people will pay more for better quality but misleading people into believing something is better quality by outright lies actually violates most consumer protection laws. I've seen no $250 monster cables at best buy here in ontario, the most expensive I saw was a $60 10ft cable by monster, however the consumer protection act is very strong and very strict here. Best Buy has screwed me over before and the mention of the CPA to a manager gets the problem resolved quickly. It appears they know they're in the wrong in many cases, but people let them get away with it - this is usually on their extended warranties from my experience.

Re:Why you should never pay more than $10 for an HDMI cable ... by matwood on Wednesday March 31, 2010 @03:20PM (#1232775)
You're confusing what I was saying. In an HDMI situation if you use a cheap cable and the picture and sound are fine, buying a more expensive cable isn't going to change anything. With HDMI in particular, if the cable is failing you'll know right away with either a poor picture or sound. It won't have the gradations that were possible when pushing an analog signal around - i.e. the picture looks could, but it could be sharper with a better cable.

I'm not sure why you brought ethernet into the mix, but generally you're talking about much longer runs than HDMI and it's often not as easy to see when your are losing packets without specifically checking if you are dropping packets (IMHO poor network performance IS failing outright, but not as easily seen as a bunch of blocks on the TV). Even then, the cable you use is either delivering all the packets or it isn't (up to an acceptable level of errors/loss for the length you are running). Delivering a stronger 1/0 isn't going to change anything as long as it's strong enough for the receiver to differentiate. That's where it either works or it doesn't comes from.

Re:Why you should never pay more than $10 for an HDMI cable ... by lkjhgvbnm on Wednesday March 31, 2010 @12:01PM (#1232134)
But did you use audiophile, linear crystal aligned cables? And did you install them the correct way round? https://usa.denon.com/ProductDetails/3429.asp

Presumably on ethernet you have to decide if you want the Tx or Rx signal to have the extra digital nuance?

Re:Why you should never pay more than $10 for an HDMI cable ... by whatusername on Wednesday March 31, 2010 @07:03PM (#1233304)
"Or run parallel to a set of Florescent light ballasts."

Really? Crap. I've just run the cable down to a back room (for an x360) - and it goes straight alongside a couple of flouro tubes.

Re:Why you should never pay more than $10 for an HDMI cable ... by wwalker3 on Wednesday March 31, 2010 @11:43AM (#1232065)
That's still not correct.

For HDMI in particular, there's no error correction at all on the video data (though there is on the audio and control data).

So if one bit gets flipped in the video data as it goes through the cable, you're going to see that wrong bit on screen. You'd have to have an insanely high bit error rate for your eyes to notice it, but it's there, and it gradually gets worse as the error rate increases.

What could flip a bit in a cable? Any number of things. EM interference from outside a badly shielded cable. EM crosstalk between conductors inside a badly designed cable. Signal reflections at badly designed connectors. Basically anything that can happen to any other cable, whether the signal that goes over it is considered to be analog or digital.

I assume the reason HDMI applies EC to the audio and control data is that errors in those channels are more noticeable to the user, whereas errors at reasonable rates in the video will mostly sneak by.

The HDMI spec at http://www.hdmi.org/download/HDMI_Spec_1.3_GM1.pdf is a great source of information about this.

Re:Why you should never pay more than $10 for an HDMI cable ... by jcromartie on Wednesday March 31, 2010 @12:58PM (#1232338)
I've had this happen. You see what are called "sparkles" when you get a lot of failures (and it truly looks like sparkling glitter on your TV). It turned out to be the TV's connector more than the cable itself. The same $4 cable worked fine on a replacement set.
Re:Why you should never pay more than $10 for an HDMI cable ... by ErrantX on Wednesday March 31, 2010 @12:01PM (#1232135)
Indeed. However it uses TMDS [1] which is a "blind mans" error reduction technique.

1. http://en.wikipedia.org/wiki/Transition_Minimized_Differenti...

Re:Why you should never pay more than $10 for an HDMI cable ... by wwalker3 on Wednesday March 31, 2010 @12:14PM (#1232178)
Totally true. HDMI takes many steps to try to reduce errors to a reasonable rate. In practice, this rate is usually low enough to ignore, even with cheap cables.

I was just making the point that there is indeed a progressive degradation in image quality with increasing error rate, even in HDMI.

Re:Why you should never pay more than $10 for an HDMI cable ... by matwood on Wednesday March 31, 2010 @03:31PM (#1232801)
IMHO, seeing sparkles on the screen means 'does not work.' Hearing audio errors means does not work. When pushing a digital signal around if you have significant errors you'll know quickly at the receivers end if the cable is bad. If you hook up your cheap cable and don't notice any of these errors, getting a better cable isn't going to make the picture sharper or sound clearer like in the days of pushing analog signals around.
Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @11:16AM (#1231981)
I think your understanding of cables is off.

All signals are analog. Every single one. (Actually, I take that back. With the exception of quantum computers, to date, all signals are analog).

A "digital" cable doesn't just work or not work. It is possible to receive spurious bit errors for many reasons. For example, you turn up the volume to your awesome surround sound speakers, which causes more current to flow through your speaker wires that happen to be running parallel to your horrible HDMI cable. The increased current causes interference in your low-power HDMI cable, causing bit errors in the transmission.

Re:Why you should never pay more than $10 for an HDMI cable ... by axod on Wednesday March 31, 2010 @11:25AM (#1232001)
>> "It is possible to receive spurious bit errors for many reasons."

Surely that's why there's error correction layered on top?

Instead of arguing about what might happen, why not find an HDMI device that'll show you how many unrecoverable bit errors it has detected in the stream... Can't be that hard to do.

If my hard disk can send data over a tiny crappy unshielded cheap USB cable without a single bit error, I'd be willing to bet money that an HDMI cable isn't that much different.

Re:Why you should never pay more than $10 for an HDMI cable ... by tedunangst on Wednesday March 31, 2010 @12:07PM (#1232157)
HDMI doesn't do error correction for video.
Re:Why you should never pay more than $10 for an HDMI cable ... by ErrantX on Wednesday March 31, 2010 @11:46AM (#1232073)
ugh, I hated signals theory at uni... but let me dust off that knowledge...

> All signals are analog.

I see your reasoning in saying this ("on the wire" etc.); your incorrect though. Not all signals are considered analog (which is important to the point being made)

Analog signals are generally susceptible to noise because they are usually non-recoverable; error checking is hard because it is a non-discrete continuous signal.

>It is possible to receive spurious bit errors for many reasons.

Yes, which is why error checking exists in all these systems. In the context of the wire alone, yes, it is not a case of "it just works". But in the case of the communications subsystem (i.e. the transmitter, medium, receiver) it really does either work or not work :)

Ultimately thought the phrase "it's digital; either it works or it doesnt" is making no comment about the actual signal. It's really saying: an expensive cable is not, due to the digital sub-system, likely to make any difference to error rates (or more succinctly: the performance of the error correction is better than the noise affect of the transport medium)

Re:Why you should never pay more than $10 for an HDMI cable ... by steveklabnik on Wednesday March 31, 2010 @11:26AM (#1232006)
Isn't HDMI supposed to do error correction on both sides, though? I could be totally making that up, I thought I remember hearing that a while back.
Re:Why you should never pay more than $10 for an HDMI cable ... by Tichy on Wednesday March 31, 2010 @11:40AM (#1232053)
There is this weird thing called error detection/correction.
Re:Why you should never pay more than $10 for an HDMI cable ... by tedunangst on Wednesday March 31, 2010 @12:06PM (#1232154)
which HDMI doesn't do.
Re:Why you should never pay more than $10 for an HDMI cable ... by Tichy on Thursday April 01, 2010 @09:58AM (#1234573)
Hm, no idea, but I find that very hard to believe. I suspect digital transmission of information is almost impossible without error correction. IANAEE, though (I am not an electronics engineer).
Re:Why you should never pay more than $10 for an HDMI cable ... by mansr on Wednesday April 07, 2010 @02:41PM (#1248056)
HDMI does have error correction. Every 8 bits of video data are sent as 10 bits on the wire.
Re:Why you should never pay more than $10 for an HDMI cable ... by ghshephard on Wednesday March 31, 2010 @05:22PM (#1233065)
Note, it's traditional on HN to add the phrase [EDIT] when making substantive modifications to comments, particularly if someone has already responded to your original comment.
Re:Why you should never pay more than $10 for an HDMI cable ... by pbhjpbhj on Wednesday March 31, 2010 @07:24PM (#1233333)
OT: The site should really help to enforce such niceties. When you edit you should get a "reason for editing" box.
Re:Why you should never pay more than $10 for an HDMI cable ... by mrcharles on Wednesday March 31, 2010 @10:45AM (#1231891)
The point is not that you can use anything, the point is that you only need a certain level, and then it's good enough. All my HDMI cables are from monoprice.com, I don't think I paid more than $4 for a single cable, and I can't imagine what kind of EM interference I'd need to mess with them. I have so many electronics in my house I'm probably on a watch list.
Re:Why you should never pay more than $10 for an HDMI cable ... by ugh on Wednesday March 31, 2010 @11:58AM (#1232122)
I guess the argument should have been that once you cross a certain threshold, cable quality doesn’t matter. That was of course also true for analog signals (human senses are only so good), but the transition from good signal to bad signal might have different characteristics with digital signals.

While a image from a analog signal will only get noisier and noisier as signal quality decreases, images from a digital signal will first show artifacts and then just stop displaying altogether. That’s a rather sudden transition. One second the signal is there, the other it's gone. Something like that just doesn’t happen with analog signals. (I’m basing this on my experience with terrestrial digital broadcasting – could be totally wrong for HDMI connection but I doubt it.)

I would guess that how sudden that transition is has something to do with the error correction and the codec of the signal. How many wrong bits can the error correction reconstruct? And, as soon as the wrong bits get past the error correction, how many wrong bits can the decoder handle and still reconstruct a image (albeit one with artifacts)? It would certainly be interesting to know how that problem was solved for HDMI connections. If you know the maximum bit error rates for your cables figuring out which are the right ones should be easy, given enough testing :)

Re:Why you should never pay more than $10 for an HDMI cable ... by mseebach on Wednesday March 31, 2010 @10:31AM (#1231854)
I think "It is digital. It either works or it doesn't" in the context of A/V refers to the quality of the converted analog signal - what comes out of the speakers or is visible on the screen. And the signal getting through can either work or not, no matter how well engineered the cable is, isn't that correct?
Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @10:46AM (#1231895)
But the reason why your digital TV shows the correct screen is because the cable transmitted the "digital" bits between your DVD player and the TV correctly. If you have a poorly made cable you will get bit errors. Electromagnetic interference from other A/V equipment could also cause bit errors. A well made cable with twisted pairs, proper shielding (few people do this correctly), and well formed connector crimps will prevent those bit errors. With bit errors, what your awesome Blu-Ray player decodes off of the Blue-Ray disc will not be what is shown on the screen (assuming there isn't bit error correction in the TV, etc.).

And your speakers are playing an analog signal. Cable quality matters even more there.

Re:Why you should never pay more than $10 for an HDMI cable ... by oostevo on Wednesday March 31, 2010 @11:08AM (#1231955)
Yup, the correct signal might not get through if you don't have perfect shielding. And a speck of dust on a CD could theoretically ruin a whole song.

That's why CDs (and cellphones, modems, and countless other digital devices) use channel encoding.[1] That way you don't have to have a perfectly noise-free signal to reconstruct the original information.

I don't know that many specifics of the DVD or Blu-Ray standards, but I'd put money on them using Reed-Solomon or something similar.

[1] http://en.wikipedia.org/wiki/Reed-Solomon_error_correction#D...

(Edit: forgot footnote)

Re:Why you should never pay more than $10 for an HDMI cable ... by mseebach on Wednesday March 31, 2010 @11:05AM (#1231944)
> But the reason why your digital TV shows the correct screen is because the cable transmitted the "digital" bits between your DVD player and the TV correctly. If you have a poorly made cable you will get bit errors.

Yes. Which is why the poorly made cable can be said to not work.

> And your speakers are playing an analog signal.

Huh? I've never heard of HDMI cables capable of carrying analog sound.

Re:Why you should never pay more than $10 for an HDMI cable ... by cake on Wednesday March 31, 2010 @10:49AM (#1231899)
I think that "it either work or doesn't" only if the receiver has some kind of cyclic redundancy check before processing the signal.

My guess is that very few digital A/V systems implement this. Proof of this is the weird sound you may hear on a damaged compact disc, it half works.

Re:Why you should never pay more than $10 for an HDMI cable ... by ramchip on Wednesday March 31, 2010 @11:19AM (#1231986)
Compact discs use something far better (in that context), a combination of two interleaved Reed–Solomon codes called CIRC, which is error-correcting (and not just detecting like a CRC). All digital A/V systems have to implement this in order to read a CD. It's made to be strong against burst errors which is why it can handle scratches on a CD pretty well. Samples can also be interpolated if something's really unreadable.

Even with an error-detecting code, there comes a point where there's too many errors to know if you received a valid code word or if the errors just "canceled each other". If 000 and 111 are your only valid words, it's still possible that a 111 gets turned into a 000 (3 consecutive errors) and there's no way to know about it...

Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @10:53AM (#1231907)
There probably are CRCs run during the decoding process, but CRCs only tell you "yes this is correct" or "no, something went wrong."

There are additional protection schemes that can detect and correct bit errors. Those are probably also run during the decoding process. The problem is that you can only detect so many wrong bits in a given word, and beyond that no correction can be made. That is probably why the damaged disc half works.

Re:Why you should never pay more than $10 for an HDMI cable ... by cake on Wednesday March 31, 2010 @11:06AM (#1231946)
Yes it depends on the way you handle the response of the CRC, you could say "give me the data I don't care" or "please try to read it again it's wrong".

In my opinion that is just the proof that it's not as simple as "it just works or not" but rather : depending on muptiple factors such as error correction and the way your algorithm works on the receiver it may "half work" no matter what kind of cable you plug in.

Re:Why you should never pay more than $10 for an HDMI cable ... by blackguardx on Wednesday March 31, 2010 @02:52PM (#1232695)
If a cable has an HDMI logo on the box, it is guaranteed to work. Specs are specs.
Re:Why you should never pay more than $10 for an HDMI cable ... by lmkg on Wednesday March 31, 2010 @01:24PM (#1232417)
There is still a qualitative difference between digital and analog signals. With analog signals, you can always get higher fidelity by upgrading components (until something else becomes the bottleneck). With digital, there are gradients of "wrong" but there is only one "right." Once you hit the threshold of bits not being flipped, getting more expensive and higher-quality components will not get you better-sounding playback. A digital cable can achieve literally perfect playback. Analog cannot reach perfection, which means it's always possible to improve.

I'm not an electrical engineer so I don't know what the threshold of perfection is, but if the consumer reports can't tell the fancy cable apart from the Radio Shack equivalent of two-buck chuck, I'm not going to worry about it.

On an unrelated note: this is a listing on amazon for 6 feet of digital audio cable for over a thousand dollars. Read the comments. Comic gold. http://www.amazon.com/Denon-AKDL1-Dedicated-Link-Cable/dp/B0...

Re:Why you should never pay more than $10 for an HDMI cable ... by lkjhgvbnm on Wednesday March 31, 2010 @03:26PM (#1232788)
>"Digital" signals are analog signals

True that's why I reject TVs with a video chipset, I want a TV and a DVD player that uses valves for the video processing.

I wonder how big an MPEG-2 decoder in valves would be?

Re:Why you should never pay more than $10 for an HDMI cable ... by lurkinggrue on Wednesday March 31, 2010 @11:53AM (#1232097)
The real time to worry about the quality of those cables is when you go over 6 feet.
Re:Why you should never pay more than $10 for an HDMI cable ... by __david__ on Wednesday March 31, 2010 @02:42PM (#1232673)
Not really, I have 2 $12 25 foot hdmi cable that work just great. I bought the cheapest one I could find because, hey, if it doesn't work I'm only out $12. But it's been working great for a couple years now.
Re:Why you should never pay more than $10 for an HDMI cable ... by frou_dh on Wednesday March 31, 2010 @01:05PM (#1232365)
Unless you are making your own cables, I don't see why.

If the >6 feet cheap cable you bought doesn't work properly then it is faulty and you can get a refund.

Re:Why you should never pay more than $10 for an HDMI cable ... by derefr on Thursday April 01, 2010 @03:31AM (#1234092)
"The real time to worry about the quality of those cables is when you go over 6 feet," would make sense as something said to the cable manufacturer. Translated to consumer-speak, that would be "it's really quite hard to find cheap HDMI cables longer than 6 feet from a well-known brand." (Of course, shady brands will just sell the crappy cables and rely on people's innate laziness and stores with no-refunds policies.)
[deleted]
Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @10:59AM (#1231924)
Are the colors 0026FF and 8026FF the same?

No, they are not. And the difference between blue (0026FF) and purple (8026FF) is a 1 bit error.

You will see an image, but not the image your DVD told your TV to display.

edit: This comment makes a lot less sense with the deleted comment removed.

Re:Why you should never pay more than $10 for an HDMI cable ... by ramchip on Wednesday March 31, 2010 @11:13AM (#1231973)
It takes a lot of noise to alter the digital signal like this. If we're talking long distance, like a telephone line, the signal gets weak enough that it can happen regularly, but on the cable from the DVD to the TV the voltage drop is ridiculously low. Noise doesn't affect your signal by 4 volts unless you have a serious problem with your system.
Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @11:23AM (#1231999)
Actually, I think that it takes the exact same amount of noise to flip a bit as it does to transmit a bit.

Through the principle of superposition, if you transmit a 0 with X watts, and I transmit a 1 with X watts, our combined signal will be somewhere in the middle, which can cause a bit flip.

I am not talking about voltage drop from end to end, which is a separate issue. I am talking about interference occurring adjacent to any point on the cable that you pick.

Re:Why you should never pay more than $10 for an HDMI cable ... by GrandMasterBirt on Wednesday March 31, 2010 @11:00AM (#1231931)
Ok when it comes to HDMI the goal was to always have good quality. The difference between an analog and digital is that digital ENCODES the information, it either gets there or not. The only thing the cable gives you is bandwidth.

Analog is different. The signal is itself the image, so a poor signal = poor image.

MAYBE if you have a projector projecting onto a movie theater screen will a better HDMI cable matter... maybe? because of bandwidth limitations if the sender is smart enough it might send info at a lower resolution. Other than that I can't see theoretically why a good HDMI cable will help.

Also on my 42'' tv, I've yet to be shown a performance improvement when connecting my XBOX 360 via component or hdmi. It looks identical. And if HDMI is better than component, then I don't see a reason why you would ever need a good HDMI cable unless you are a movie theater and the theoretical problem does exist.

Edit regarding bit errors... Lets assume that the cable you bought is a good quality cable. By good quality I mean most seem to be shielded and not cut and no shorts. This is a reasonable expectation. I've yet to see an argument for buying more expensive super gold plated uber network cables. Hey why is your network cable that handles SO MUCH DATA not gold plated shielded etc.?

Re:Why you should never pay more than $10 for an HDMI cable ... by micks56 on Wednesday March 31, 2010 @11:32AM (#1232031)
My network cable that handles all my data doesn't have gold plating or shielding because the cable as designed is sufficient to operate at Ethernet speeds, temperatures, humidity, etc.

If you want to operate a faster network, or one in a harsh environment, you will be using shielded cables with gold plates and more twists per inch.