https://docs.google.com/spreadsheets/d/1wJwqv3rTNmORXz-XJsQa...
http://smile.amazon.com/dp/B018F8BGLA
It's worth noting that the Nexus 5x doesn't do USB 3.1, so even if you get a fancy Super Speed cable like this one, you are still suck with slow charging from your computer's USB A port.
When you plug it in, turn it off, then back on. Down at the bottom, near the fingerprint, it should indicate the type of charging you're getting. I've seen three modes, and I apologize for not knowing the distinctions, but they're "charging slowly", "charging" and "charging rapidly".
Times are commensurate to the charge mode, and rapid charging is unsurprisingly quite fast.
Another thing that might be the case is if the OP is going from actual empty to full without turning it on, which should (to some extent) expedite charging as there is no discharge happening at the same time, maybe.
Each cable needs one of 3 resistors depending on them being a A/B-to-C cable, 1.5A C-to-C cable, or 3A C-to-C cable.
Note that the A-to-C cable may well be able to carry 3A, but it shall never use the 3A C-to-C resistor (what many of the cables he find as faulty does).
Note that all this resistor shenanigans are all independent of the Battery charging spec that has been around for some years, and also the Power Delivery spec that was introduced along with the 3.1 USB spec (can be used for all ports) and the C port spec.
Never mind that a C port has so many extra pins compared to a A or B port, that one would think that id-ing a A-to-C cable would have been as simple as looking for life on any of those extra pins.
No, for C-to-C connections, the resistance is provided by the host ("downstream-facing") port, not the cable. The resistor in an A-to-C cable is basically emulating the signal that would otherwise be provided by the host.
There's no such thing as a "1.5A C-to-C cable"; all type-C cables are required to deliver at least 5A. The limiting factor is the host, not the cable, which means the cable must not incorrectly advertise capabilities that the host doesn't support.
> Never mind that a C port has so many extra pins compared to a A or B port, that one would think that id-ing a A-to-C cable would have been as simple as looking for life on any of those extra pins.
That's exactly what the new CC pin is used for. Right now the spec says "legacy cables should connect CC via a 56kΩ resistor", but it wouldn't matter if instead the requirement had been "legacy cables should leave CC disconnected"; the issue is that cable manufacturers are ignoring the spec.
4.11 could really use a massive cleanup for readability it seems.
1.5 A is required to be supported by USB-C, while 3 A is optional. Everything over it is covered by USB Power Delivery, which requires a marking of the cable which of the 5 profiles are supported.
It's just as complicated as it needs to be. And for godssakes, the pin-out diagram isn't that complicated; it only has 24 pins! There's no excuse for flipping two of them. 24 pins is not beyond the pale of what we would reasonably expect manufacturers to be able to wrap their heads around.
http://bi9he1w7hz8qbnm2zl0hd171.wpengine.netdna-cdn.com/wp-c...
You use the pins on both sides to do four-lane DisplayPort, or DisplayPort and USB 3 at the same time, or Thunderbolt.
https://news.ycombinator.com/item?id=10508494
I don't have any devices right now that use USB-C, but whenever I see a deal pop up for one, I usually check the Amazon listing to see if this guy has reviewed/certified the cable yet.
I recommend others do the same. It's not worth damaging your $800+ laptop because you wanted to save $10 on a cable.