This sub-bit jitter and interference can travel along with a digital file and sneak right past your ordinary bit-level error detection and correction, no matter how lossless you make it. That's because these errors aren't visible in the bits. They occur at a deeper and more subtle level, in between the bits.
Even if you prove mathematically that two files contain the exact same bits, you can't prove that the human ear won't hear any difference, can you?
Same file -> same playback.
If you hear the same sound file twice (or two identical files) and hear something different, you software is broken or you're imagining things.
Can you turn this into mere "bits"? Of course not!
That's why it is so important to protect against sub-bit quantization errors, and this can only be done with proper interconnects. Ordinary cables allow the bits to travel willy-nilly until they jam up against each other creating a brittle, edgy soundstage. Quality interconnects are tuned, aligned, and harmonically shielded to keep those precious bits - and the all-important spaces between them - in a smooth flow.
And then, we can hear all of the things that make us human.
That comment is just perfect.
(I put the scare quotes on because I haven't actually bothered to check if there is an audible difference. But it does confirm the GP's experience.)
"military-grade encryption"
I remember experimenting with writing a CD ripping program in the 90s, using Windows APIs, and I found, like you, that I got different data each time. But modern rippers such as EAC does this stuff much better and will for the most part give you bit-perfect rips.
That mat does nothing. And if you read that linked page, you will see that he claims it drastically improves audio quality (bass, etc.), which is pure nonsense.
Err, no.
That makes sense when you have an analog version of the audio picked up by an analog transducer (i.e. a vinyl record) but makes no sense with an isochronous stream of quantized samples.
I suppose a vibration could cause a small phase shift in when the sample physically appears under the LED, but but since the D->A conversion is clocked by a PLL it is irrelevant.
If you have extreme warping or shaking (e.g fling your discman onto the floor or stick your finger on the disk while it's spinning) then a sample might not appear at all, but that's something different than you are talking about.
I suppose it's theoretically possible that some extreme warping or vibration could cause a bit flip, but that's what the ECC is for.
"[…] The change in height between pits and lands results in a difference in the way the light is reflected. By measuring the intensity change with a photodiode […]"
I'm no signals expert. Are you saying that there is no quantization in that intensity change measurement?
Regardless of quantization, maybe you're right on vibration not being a major source of errors (I know little about electronics and PLLs).
But then, what are the error sources that made the engineers put an extra 276 bytes of Reed-Solomon error correction per 2352-byte sector on a mode-1 data CD-ROM (vs none on an audio CD, which has just has the frame ECC and nothing extra). See https://en.wikipedia.org/wiki/CD-ROM#CD-ROM_format .
Some statements just don't age well ...
You sure there isn't something in the wavs like a creation date field that would always cause the checksum to be different? That would make way more sense than "vibration"....
An 80-minute, 700 MB CD-R fits 80 * 60 * 44100 * 2 * 2 / 2^20 ~= 807 MB of audio.
Why is that?
The 100MB difference is not just due to the audio TOC being of smaller size than the ISO9660 or UDF file system metadata. It's also because of differences in error correction. I don't have the spec on hand but I recall from when I was investigating this that CD-ROMs use more bits for error correction than audio CDs. That's why you can fit more audio data than "filesystem data" on a CD-R. Reading (ripping, digitally) an audio CD will likely result in different digital audio files every time, since the error correction is not that good, but good enough, for audio.
I read into this when I was wondering why my CD-DA extracted .wavs came out with a different checksum every time. Vibration is one of the factors that would make the same audio CD, read with the same CD player, produce different digital signals some of the time or even every time.
CD-ROMs however, which store digital data, need better correction - you definately don't want a bitflip in your .exe, while a minor amplitude diff — an uncorrected bitflip in the upper bits of a 16-bit PCM signal — is no biggie.
So… I'm not saying that the people using CD mats are informed (or have tested whether the mat makes a difference, or would even know how to go on about testing this, scientifically), but there's more to it than what I originally thought — which was "it's digital so it's never degraded". I wouldn't have known without checking the md5sum of my .wav, though.