News for hackers. Stuff that matters.
Re:Fuzzing on Edison: field report by StavrosK on Monday October 13, 2014 @10:10AM (#8448751)
Has anyone tried the Edison? Is it good? It seems to me that it's a Raspberry Pi with better specs, wifi, etc, plus Arduino compatibility, which sounds amazing, but I haven't figured out how it connects to stuff. How do I power the little die? Do I need breakout boards for everything?
Re:Fuzzing on Edison: field report by elecengin on Monday October 13, 2014 @10:14AM (#8448770)
The Raspberry Pi is intended for a different use - it's comparing apples to oranges.

The Edison is intended for embedded applications - it has no display support built in (like DVI/HDMI), less USB support, and less "plug-and-play" ports.

SparkFun did a great write-up on unfair comparisons between the two platforms: https://www.sparkfun.com/news/1603

Re:Fuzzing on Edison: field report by StavrosK on Monday October 13, 2014 @10:18AM (#8448791)
Sure, but I (and most of the hackers I know) use the Raspberry Pi like an Edison (i.e. only Wifi connected to USB, headless/SSH only, GPIO pins), so the Edison would be a better fit for my projects, if I could figure out how it works.

As the SparkFun article mentions, with the cost of the Wifi, powered hub, cables, SD card, and Bluetooth adapter add up. The Raspberry Pi is meant as a low-cost teaching computer, whereas what I want is a SoC to hack on.

Maybe it's as simple as programming it with the board and then detaching it and powering it.

Re:Fuzzing on Edison: field report by joezydeco on Monday October 13, 2014 @10:20AM (#8448800)
See, that's where I don't get what Edison is about.

If I want a SoC capable of doing low cost user-interface type embedded tasks I need parallel LCD support (or at least LVDS). I'd get an NXP LPC18/40 or an STM32 at the low end or an i.MX5/6 at the high end. Way cheaper with way better application support.

If I wanted to do IoT sensing/reporting, this whole thing is just overkill. Again, a low cost LPC or STM coupled with a GainSpan or TI radio module (that I can bake directly to my PCB). To me, and I could be wrong here, IoT isn't about putting 500 MHz computing resources at the nodes and certainly not for a $75 BOM adder.

At least the LPC and STM are chips I can put directly down on my board and run out of the box. An SOM with a single-sourced connector (and Hirose is notorious for designing unique stuff nobody else wants to duplicate) is just commercial suicide.

Re:Fuzzing on Edison: field report by StavrosK on Monday October 13, 2014 @10:23AM (#8448814)
I want a low-power, Wifi-enabled computer for various projects. Arduino shield compatibility means that I can create things like my license-plate-reading garage door opener, or irrigation system, while combining a fast processor and lots of RAM with all the nice hardware Arduino has.
Re:Fuzzing on Edison: field report by joezydeco on Monday October 13, 2014 @10:42AM (#8448876)
And that's fine for that kind of application. You could also do just as much with a cheaper system (but you'd need a lot more software work so maybe that's Intel key point: you can shovel in all the X86 code you've been slogging around with you for decades).

But, in my opinion, the examples you mentioned are not IoT. Unless you're planning to put one of these at every sprinkler head.

Re:Fuzzing on Edison: field report by StavrosK on Monday October 13, 2014 @10:45AM (#8448891)
They aren't, but you said you don't get what the Edison is about, so I mentioned a few cases it's perfect for.
Re:Fuzzing on Edison: field report by 13 on Monday October 13, 2014 @11:02AM (#8448952)
It's neat, but hard to come up with a use case that's not a part of a commercial product just yet. As a unit the 0.4mm pitch connector is absolutely impossible to solder in a DIY environment, you must buy a breakout board, and suddenly it's not a sub $50 device anymore. All of the use cases I could think of were better served by a device I could actually tinker with, so I hedged on a Minnowboard Max instead.
Re:Fuzzing on Edison: field report by simpsond on Monday October 13, 2014 @02:06PM (#8449776)
In terms of the specs, the Edison is great. After tinkering around with it for a bit I found I didn't really like the bundled software Intel released with it.

At the end of the day I want something just like this, but with a net-installish base linux distro, and something with better temperature range than 0-40C! It's too complicated for tinkering, and the temperature range is too narrow for commercial products. It falls into the middle, where it's probably not great for anyone. I'm sure Intel can fix that.

Re:Fuzzing on Edison: field report by unwind on Monday October 13, 2014 @10:17AM (#8448785)
I haven't tried it (not in the market for it).

You typically need an "Edison Block" (like an Ardunino Shield) to connect to things, see e.g. SparkFun's portfolio at <https://www.sparkfun.com/categories/272/>.

Not sure how power is applied, it's not as obvious as for the Arduino (since the Edison is more highly integrated and more designed to be built into products than to be directly fiddled with, I guess).

Re:Fuzzing on Edison: field report by rasz_pl on Monday October 13, 2014 @01:08PM (#8449529)
http://www.eevblog.com/forum/microcontrollers/intel-edison-3...

its a gimmick, there is no clear market for it, no clear use scenario, no real documentation, a lot of design fails (230Hz GPIOs IF/when Intel lets you use buildin Quark, its TURNED OFF now)

Re:Fuzzing on Edison: field report by illumen on Monday October 13, 2014 @10:26AM (#8448818)
Checkout the pcduino for a raspberrypi type board + arduino in one.
Re:Fuzzing on Edison: field report by StavrosK on Monday October 13, 2014 @10:44AM (#8448886)
Thanks, that looks good, but it's more expensive than the Edison and doesn't have WiFi, as far as I can see.
Re:Fuzzing on Edison: field report by mrti on Monday October 13, 2014 @06:34PM (#8451047)
pcduino3 has been available for a while now with wifi built in - I've found these boards quite useful for mobile applications. I've been using them to run a django app quite nicely where the raspi wasn't quite powerful enough!
Re:Fuzzing on Edison: field report by StavrosK on Tuesday October 14, 2014 @10:38AM (#8453587)
Oh, that sounds great! Is it Arduino compatible? How do you use all those libraries? I don't understand how something that runs Linux can be Arduino compatible, since Linux isn't a RTOS.