I would be shocked to see even one laptop ship with USB power before 2015.
E.g. the EEE 1000HE uses a 12V adapter, and it has 16V caps in its power circuit. Probably the same for the Surface/Pixel.
Yes, there is: it causes massive electronic waste because of incompatible chargers. Expect the new EU regulation that covers phones etc. (that replaced "voluntary" measures) to be expanded to cover laptops too, or at least for manufacturers to get threatened with changes to th regulation, if manufacturers don't voluntarily switch to USB once suitable chargers start being widely available.
However, the solution is not a grossly overcomplicated standard like USB. It is a 20V barrel plug. Maybe if you want to get really fancy, include a resistor on a third pin for wattage encoding. Standardise on that instead - or pick an existing size - there are enough to choose from already ( http://en.wikipedia.org/wiki/Coaxial_power_connector#Standar... ).
With the exception of the phone charging example, I would agree. The PS/2 protocol is vastly less complex than USB, and parallel ports are so simple they can be used as GPIOs with ultra-low guaranteed latency. Phones migrated to USB because they already needed the bulk data transfer capability along with power, and USB made for a good fit.
You won't be able to charge your phone with your standard barrel plug laptop charger, so you'll still have to carry two adapters when you travel.
The Dart has both USB and a barrel plug, which is the same as many other aftermarket adapters. (They could've made this more obvious in the marketing material, e.g. by showing USB devices plugged into it and not just laptops most of the time.)
I'll choose a laptop with a big robust barrel plug, and one that can be powered from anything outputting 12-24VDC, over one with a USB socket and requiring complex negotiation protocols to even start consuming power. It's the KISS principle. Standards that try to do everything don't tend to do any one thing particularly well, and introduce unnecessary complexity.
Detection of power delivery plugs is mechanical for standard A connectors (their male standard-A connectors are 1.3 mm longer so they could be inserted deeper in female power delivery connectors than conventional connectors so metallic shield connects detection pins) and based on detecting resistors and capacitors between ID pin and ground and power pins for other connectors.
For voltage negotiation new simplified bus and protocol was invented; it uses high frequency transmission on the same pin as power.
So even if adding a new USB port for charging is cheap and easy, the manufacturers might still have reasons not to do it.
Also, laptops have very flexible power input circuits that will accept a wide range of DC input: they'll start running from ~12V (the voltage of an almost-dead battery), and go as high as the voltage specs on the input components allows - 25V (filter caps) is the usual absolute upper limit. Higher voltage means lower I^2R losses but manufacturers like to leave some safety margin, which is why 20V is somewhat of a de-facto standard given the parts available. The general power distribution circuits in a laptop are like this: there's a main power rail, whose voltage varies with battery voltage when running on battery, and is the DC-IN voltage with the adapter plugged in. The voltages for the CPU, GPU, chipset, etc. are all generated by DC-DC converters supplied from this main rail. There's a set of diodes/MOSFETs that wire-OR together the battery and DC-IN to the main rail, preventing current flow in the wrong direction. It also powers the battery charger.
I've read a lot of laptop schematics, and all of them use very similar power circuitry, often with the same components. The only real concern with device compatibility is in the ID schemes that some manufacturers use, either to "lock out" third party adapters or encode wattage selection. The simplest ones are nothing more than a resistor in the plug, different values for different wattages (IBM/Lenovo is one example). More complex ones use a 1-wire interface to an EEPROM or other storage element (Dell, Apple) (http://www.laptop-junction.com/toast/content/dell-ac-power-a... http://www.righto.com/2013/06/teardown-and-exploration-of-ma... ). Then there's all the others that have no ID at all, just +/- input, and these are the most compatible.
About the Dart itself: the technology used here (VHF SMPS) has been around for a long time in military/aerospace applications, where size/weight is more important than reducing switching losses.
http://www.eevblog.com/forum/crowd-funded-projects/vhf-lapto...