Competitively the US does well in energy tech and agriculture tech. The US is #2 in wind power, #2 in solar power, #1 in nuclear power, along with being the world's biggest oil & natural gas producer. The US industrial rail system is also an epic scale marvel, while its consumer rail system is pathetic.
It's definitely not elite in most infrastructure (including electrical plugs).
If you were than combined figures put USA behind places like Germany and Spain.
And bringing nuclear into it you get France absolutely trouncing.
So your argument is that “america is a big country”.
Meanwhile Europe standardized bank transfers with IBAN, killed connector type proliferation with by standardizing on USB-C, and routed 3-phase power most homes. Oh, and the metric system. And while Europe has a wide range of cultures and functionality of government, a lot of places have simpler tax forms and a more prescriptive legal system (as opposed to the precedent-dominated Common Law tradition in the US). The German-speaking countries even rewrote spelling to make it simpler.
I view a lot of this stuff as infrastructure investment. We shouldn't have to stumble over the mundane to do interesting things. As others have commented, Europe also had the advantage of adopting some technologies later, but in some cases they just seem to be more aligned with a system of constant (if sometimes frustratingly slow) improvement.
What is the advantage to this? Are there use cases for using all three phases (in one appliance?)?
The difference between one three-phase feeder and three completely separate two-wire circuits is that the three phases, which are 120° apart, share a single neutral conductor. In fact, if the load is perfectly balanced across the phases and currents are sine waves, they will cancel each other out, so neutral will carry no current at all and can be omitted! But in practice, there still usually is a neutral conductor to carry the imbalance (except for specific loads like delta and star motors under certain conditions). In total, we only need 4 wires instead of 6 to carry the same amount of power. That's 1/3 less copper! (Excluding PE of course.)
Now, compared to using a single two-wire circuit rated for three times the current, three-phase also wins by a long shot. (We're again assuming a balanced load and equal power factors.) This is because resistive heat scales with the current squared, so 3 times the current produces 9 times the amount of heat at the same resistance. So, we need to use thicker conductors to lower the resistance. But the area of its cross-section grows quicker than the surface area to dissipate heat, so the maximum current a conductor can safely carry scales sublinearly with its cross-sectional area. For example, 1.5mm² will suffice under most conditions to carry 16A, but for 48A we'll typically need 10mm².
All in all, the rule of thumb is that three-phase AC gets you the same amount of power for roughly 25% less copper compared to single-phase AC!
Some loads also make use of the rotating magnetic field, like motors (see below).
Lastly, lower currents will reduce heating in case of loose connections, reducing the risk of fire. On the other hand, a 400V RMS phase-to-phase shock is a lot more severe than a 230V RMS phase-to-neutral (or phase-to-PE) shock.
Common use cases (load-side):
- Motors. Three phases produce a rotating magnetic field, perfect for simple self-starting motors. (Arguably, this is less relevant today with more modern motor designs, though three-phase induction motors are still widely used.)
- Electric cookers (usually split by cooking zones and oven, like one phase for two zones each, and the third phase for the oven)
- Water heaters (especially those that heat water instantaneously on demand)
- EV charging (even an ancient European three-phase installation is likely able to deliver 11kW of power and can therefore fully charge an EV overnight)
So, when I arrived in Barcelona and Catalonia, I was pleasantly, mildly surprised that not only had Europe kept pace with us techno-mages in America, but they had some kind of parallel evolution going on, in terms of connectors, interfaces, protocols, etc.
My fiancée was sort of mystified, because my favorite subject of photography was not landmarks or her pretty face, but the circuit breaker box, the rear of her television set, the A/C unit, and any other cool, distinctly Euro-tech instances I could identify around there.
I tried helping her adjust/fix her aerial TV antenna, got zapped a few times; discovered that Catalonian TV antennas are energized with a few volts for whatever reason; decided that Euro-tech is beyond my expertise to tinker with on someone else's behalf, especially a native family.
Thankfully, I didn't have any portable electronics or appliances in my luggage that needed adapters or plugs, but the experience was truly humbling, and eye-opening, and I returned to the United States with a better calibrated worldview.