News for hackers. Stuff that matters.
Re:I stopped trusting USB-C cable labels and started testing... by ChrisMarshallNY on Friday August 07, 2026 @12:10AM (#49205818)
Think about it.

You need to generate a precise, calibrated, 40GHz signal, transmit it, then precisely measure the returned signal for phase, amplitude, and waveform integrity -at that speed.

Oscilloscopes and logic analyzers that run at that speed, are damn expensive.

Re:I stopped trusting USB-C cable labels and started testing... by CamperBob2 on Friday August 07, 2026 @01:55AM (#49206360)
Someone could do an equivalent-time sampling instrument for not much money, if the market were there. It's probably not, though.
Re:I stopped trusting USB-C cable labels and started testing... by ChrisMarshallNY on Friday August 07, 2026 @06:42AM (#49208397)
Time sampling isn’t enough.

You need to at least look at waveform integrity (which can be approximated, by doing things like looking for harmonics).

For example, you may send in a 40 GHz square wave, and get back a wave full of ringing, or a sine or sawtooth wave. It’s damn difficult to maintain clean square waves, at that frequency. The cable could also double as a microwave antenna.

Since it’s digital information, some waveform alterations are OK, but not too much. You need fairly clear state transitions. Ringing, or waveform distortion, can introduce extra (or fewer) transitions; thus, completely changing the data.

Re:I stopped trusting USB-C cable labels and started testing... by CamperBob2 on Friday August 07, 2026 @12:07PM (#49212589)
That's not really what I mean. You don't have to diagnose the signal, just the medium, which can tell you what will happen to the real signal. It requires a fast edge, but nothing much beyond that.

E.g., here's what a bad connector at the far end of an SFF-8654 cable looks like on a TDR: https://i.imgur.com/AiLnSuC.jpeg This type of plot can be interpreted as impedance versus distance along the line. It can be made with a small handheld instrument, but currently a human is needed to read the tea leaves. While I was making that measurement, I couldn't help but think that it would be nice if it didn't require either a 50 GHz VNA or equally-expensive training to read.

Re:I stopped trusting USB-C cable labels and started testing... by ChrisMarshallNY on Friday August 07, 2026 @01:44PM (#49213840)
Fair 'nuff.

As long as we don't get false positives. They are worse than false negatives, and is what happens, when you just read the markers from the chip. As we know well, lots of dodgy C.M.O.T. Dibbler-types will deliberately program the chips to emit bogus markers.

Re:I stopped trusting USB-C cable labels and started testing... by roaringrocky on Friday August 07, 2026 @03:52AM (#49207201)
But for bandwidth can't you just have two simple computers at either end that can send a 100GB file and if it arrives in 20 seconds, you know you have 40gbps of bandwidth?
Re:I stopped trusting USB-C cable labels and started testing... by traceroute66 on Friday August 07, 2026 @05:03AM (#49207730)
> But for bandwidth can't you just have two simple computers at either end that can send a 100GB file and if it arrives in 20 seconds, you know you have 40gbps of bandwidth?

Because that is not reproducible and introduces all sorts of other random variables to your test.

Expensive equipment is the only answer here.

Its a bit like when you ask an electrician to install network cable (yuk !).

They consider their job done after a continuity test (if they bother to do a continuity test at all).

Meanwhile, if you put a Fluke on it, you will pick up all sorts of subtle faults that the electrician's continuity tester will never pick up, but will cause subtle and hard-to-diagnose problems when you try to push data over the cable.

Its the same thing with all those cheap USB testers.

They might have all sorts of fancy displays, but in the end they are no substitute for the real thing and will end up lulling you into a false sense of security.

Re:I stopped trusting USB-C cable labels and started testing... by criddell on Friday August 07, 2026 @09:01AM (#49209767)
If you buy decent cables from reputable companies (CableMatters, LTT, Apple, etc...) you could end up with a drawer full of high quality mystery cables. A cheap tester is probably all you really need to sort out that mess.
Re:I stopped trusting USB-C cable labels and started testing... by chainingsolid on Friday August 07, 2026 @02:58PM (#49214851)
You mention a Fluke, which I'm assuming is in relation to an ethernet cable tester (made by Fluke). I've seen/used continuity testers, but not something better (I've been using iperf3) Could you link/include the sku/model number of what you are refering too?
Re:I stopped trusting USB-C cable labels and started testing... by fragmede on Friday August 07, 2026 @03:00PM (#49214873)
Re:I stopped trusting USB-C cable labels and started testing... by chainingsolid on Friday August 07, 2026 @07:29PM (#49217428)
That would explain why I haven't seen one! Thanks for the info.
Re:I stopped trusting USB-C cable labels and started testing... by traceroute66 on Sunday August 09, 2026 @05:42AM (#49229899)
> Only $2,500!

Actually no. That one is no good.

The one I had in mind is the one that professional network cabling installers use.

This one: https://www.cdw.com/product/fluke-dsx-cableanalyzer-dsx2-500...

Only $13,000

:)

Datasheet: https://www.flukenetworks.com/datacom-cabling/Versiv/dsx-cab...

Re:I stopped trusting USB-C cable labels and started testing... by fragmede on Sunday August 09, 2026 @05:48AM (#49229922)
I didn't want to scare anyone off

Your link 404's for me, here's it on Amazon.

https://a.co/d/02K5Kdvy

Note: not an affiliate link but if I had one I'd totally use it here ;)

Re:I stopped trusting USB-C cable labels and started testing... by rtkwe on Friday August 07, 2026 @12:02PM (#49212491)
You have to first identify and ensure the two devices and their ports are capable of reliably creating and absorbing that data rate too or you'll never know if it's the cable or the devices that causes the cables to fail. What if your devices can but only intermittently or a software/firmware update messes with it's capabilities?

Dedicated test equipment that can reliably and verifiably test these high speeds is niche and therefor expensive. There's not really a way around that issue.

Re:I stopped trusting USB-C cable labels and started testing... by LorenPechtel on Friday August 07, 2026 @06:59PM (#49217242)
But do you actually need that at the consumer level?

Make some properly formatted garbage, send it down the wire to the other end of the tester and see if you can read the result. It won't tell you if the cable is marginal, but how often is that actually an issue? Network cables are connected to hardware that retries, masking such errors.