News for hackers. Stuff that matters.
Re:A modern 8 bit design, built using 1950s thermionic valves by 082349872349872 on Thursday June 27, 2024 @03:39PM (#40814242)
> When all the valves are glowing, I check the fire extinguisher is full, and run the code.

It wasn't until working with valve hardware that I finally grokked the original difference between a cold boot and a warm one.

Re:A modern 8 bit design, built using 1950s thermionic valves by ahazred8ta on Thursday June 27, 2024 @06:27PM (#40815873)
♫ "And when they turn the power on, it's sure to dim the lamps / At plus and minus 16 volts and fourteen hundred amps." -- Frank Hayes
Re:A modern 8 bit design, built using 1950s thermionic valves by JJMcJ on Thursday June 27, 2024 @07:56PM (#40816476)
Telephone central exchanges used to have enormous lead acid battery (like automobile batteries, the starter motor not the EV kind) arrays if they lost power.

It was amazing to see the battery array discharge ammeter at 5000 amps when utility power went out.

Re:A modern 8 bit design, built using 1950s thermionic valves by _joel on Friday June 28, 2024 @06:33AM (#40819309)
some ISP's still do (or did, last time I was in one), at least one I worked for a few years back. Had a room full of lead acid batteries on shelves and another with a big spinning wheel to smooth out the flow.
Re:A modern 8 bit design, built using 1950s thermionic valves by Terr_ on Thursday June 27, 2024 @07:14PM (#40816190)
Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @12:37AM (#40817762)
What?

Silicone hardware generates heat.

Neither silicone hardware nor tube hardware goes literally cold in a cold boot; just the power is cut for a moment, usually not long enough to lose a lot of heat.

Re:A modern 8 bit design, built using 1950s thermionic valves by cjs_ac on Friday June 28, 2024 @04:10AM (#40818659)
The difference is that for solid-state logic, the heat is purely a waste byproduct, whereas for thermionic valves, the heat is the energy used by the electrons to move between the electrodes, hence the name. If the valves are cold, you have to wait for them to warm up before they can do anything.
Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @06:15AM (#40819220)
All the same, "cold boot" doesn't refer to letting tubes cool down. If power is restored while the tubes are still hot, it's still a "cold boot".

The electrons are not moved by heat; they are moved by the electric potential between the electrodes. The heat goes into maintaining the cathode at a certain temperature, at which the electrons "boil off" in sufficient numbers, but that requires only a smidgeon of the energy. Though depending on it, tubes are incredibly wasteful of heat.

So you say silicon and other parts don't require heat? Check that data sheet again! If the part's operating range is from -40°C to 70°C, then that part requires heat. If the ambient temperature happens to be -100°C, you have to heat it, perhaps by installing a heating filament into the chassis.

E.g. check the TI datasheet for the NE5532 op-amps:

Free air operating temperature:

NE5532, NE5532A: 0 to 70°C.

SA5532, SA5532A: –40 to 85°C.

(That standard part is quite delicate there, only down to zero!)

Conversely, thermionic tubes for a hot environment could be built without heating filaments. If the ambient temperature is 500°C, and that happens to be quite enough for that tube's cathode, then it Just Works, like your NE5532 IC at 3°C.

Re:A modern 8 bit design, built using 1950s thermionic valves by Max-q on Friday June 28, 2024 @07:20AM (#40819516)
The valves need to be warmed up can still be the source of the names "cold boot" and "warm boot", even if we today have given them different meaning.
Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @08:55AM (#40820163)
The meanings we give them today go back almost 50 years.

Then the trail runs cold, pardon the pun.

According to Google n-gram searches, "cold reboot" and "warm reboot" didn't exist at all until the late 1970s.

Related terms like "cold boot" and "warm boot" come up, but only in references to footwear. Can't find any computer uses 1950-1970.

The "cold start" and "warm start" mostly come up in automotive, aviation or marine contexts, confounding the search. Likewise, not finding computer uses.

Not finding computer uses for "cold restart" and "warm restart", either.

All these terms take off as computer terms in the late 1970's.

By the way, an important feature of the warm reboot is (possibly) that data is still in memory (if you have the kind of machine whose memory is wiped when power is cut, not magnetic core). In machines with simple operating systems, you could recover your program or data from memory after a reset.

(I think the timeline in the n-grams coincides with the explosion in microcomputing and reflects that: penetration of the jargon into mainstream writing. Nevertheless, the case doesn't seem to be good though for a vacuum tube origin of warm {start/restart/reboot}.)

Re:A modern 8 bit design, built using 1950s thermionic valves by tlb on Friday June 28, 2024 @08:55AM (#40820161)
Is this known to work? I would have thought that running a whole tube at high temperature would cause the grid to emit thermal electrons, creating a current between grid and plate. Even though the grid doesn't have the low-work-function coating that the cathode does, its surface area can be larger and it's usually more negative than the cathode so I'd expect substantial currents.

If this does work, you could save a lot of power by building heated, insulated enclosures for entire tube appliances rather than heating each cathode and cooling every tube.

Re:A modern 8 bit design, built using 1950s thermionic valves by tlb on Friday June 28, 2024 @01:04PM (#40822628)
Though I guess you could save even more power by using transistors.
Re:A modern 8 bit design, built using 1950s thermionic valves by hilbert42 on Saturday June 29, 2024 @04:02AM (#40828614)
"Conversely, thermionic tubes for a hot environment could be built without heating filaments. If the ambient temperature is 500°..."

There's a lot of physics and engineering behind thermionic emission in a typical vacuum tube and the subject shouldn't be overlooked just because tubes are less commonplace than they once were.

Until the transistor became popular in the latter half of the 20th C. essentially all of electronics relied upon thermionic emission so much effort went into understanding it. Moreover, it's still very important in specialized areas such as in scientific instruments, high power transmitting tubes, TWTs (Traveling Wave Tubes), CRTs, etc.

Thermionic emission obeys Richardson's Law—after physicist Owen Richardson who received the Nobel Prize for his work in 1928, and its study is an essential part of thermodynamics: https://en.m.wikipedia.org/wiki/Thermionic_emission.

When I was learning about this stuff I had a little book titled Thermionic vacuum tubes and their applications by Sir Edward Appleton (who is more famous for his wartime research into radar). Still, for anyone who's interested in thermionic emission then this could be a useful reference.

I'd add that when it comes to practical methods of manufacturing thermionic cathodes, info on low work function oxide emitters etc. then there are references that are better or more practically orientated (but offhand I cannot remember the names of any).

Re:A modern 8 bit design, built using 1950s thermionic valves by 01HNNWZ0MV43FF on Friday June 28, 2024 @01:05AM (#40817897)
Silicon. Silicone is the plastic used to make crummy kitchen utensils
Re:A modern 8 bit design, built using 1950s thermionic valves by Doxin on Friday June 28, 2024 @02:35AM (#40818281)
Silicone is a rubber made to make good kitchen utensils. The crummy plastic ones tend to be nylon or the like. Biggest tell is that silicone does not melt.
Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @02:50AM (#40818341)
I'm amazed I made the typo twice in the same post.

Kazinator comments containing "silicone":

https://hn.algolia.com/?dateRange=all&page=0&prefix=false&qu...

Kazinator comments using "silicon"

https://hn.algolia.com/?dateRange=all&page=0&prefix=false&qu...

Re:A modern 8 bit design, built using 1950s thermionic valves by klyrs on Friday June 28, 2024 @12:12PM (#40822102)
> kazinator|7 years ago ... Love the irony of how silicon is used.

Common confusion; silicon is a metalloid, irony is metallic

Re:A modern 8 bit design, built using 1950s thermionic valves by hilbert42 on Saturday June 29, 2024 @04:21AM (#40828663)
Take heart, you're not alone, my WP's speller has automatically corrected to 'silicone' on more than one occasion and I've not noticed the embarrassing mistake. ;-)
Re:A modern 8 bit design, built using 1950s thermionic valves by tass on Friday June 28, 2024 @01:01AM (#40817881)
I imagine these terms could have changed over time, but consider that a warm boot might have meant power off and on with these old computers.

One difference is that the valves have more chance of burning out on a cold boot due to the temperature change.

Re:A modern 8 bit design, built using 1950s thermionic valves by jaystraw on Friday June 28, 2024 @04:34AM (#40818782)
in the music world, variacs are used to bring old tube amplifiers up to power slowly for that reason. not after being repaired or refurbished generally, but certainly when the amp's condition is unknown. the author of tfa said his new power supplies do that automatically, which is pretty neat.
Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @04:41AM (#40818812)
Filaments experience a high inrush current on startup because their resistance is lower when they are cold. That's why incandescent bulbs often burn out on powerup, rather than in the middle of a duty cycle.

Tube filaments last a good long time though, particularly in small signal tubes.

They do not shine like light bulb filaments; they glow red.

The circuit designer also has a say in it; tube filaments can be operated over a range of currents: you can run tubes hotter or colder. In a digital application, you'd probably want to go as cold as you can get away with for longer life.

Tubes have various modes of failure in addition to burned out filaments, like "gassing out", or the cathode emission decreasing, eroding the gain. Of course, abnormal conditions like parts melting from overcurrent.

Speaking of incandescent bulbs: those are victims of planned obsolescence. A bulb can easily be made that will last 50 years; it's just not profitable because you can't charge 50 times more for it than one that burns out in a year. Once everyone has 50 year bulbs, you're out of business.

Re:A modern 8 bit design, built using 1950s thermionic valves by ekidd on Friday June 28, 2024 @06:58AM (#40819421)
> Once everyone has 50 year bulbs, you're out of business.

This seems to have been the issue with the expensive Philips Hue LED bulbs (the ZigBee ones). We installed ours close to a decade ago, and we took them with us when we moved to a new house. I don't think I've replaced a single one yet.

Philips seems to have de-emphasized that set of bulbs in favor of cheaper models, as far as I can tell?

Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @10:15PM (#40827405)
I have 13-y-o Phillips LED flood lights in some track lighting (50W equivalents, maybe?). Working great!
Re:A modern 8 bit design, built using 1950s thermionic valves by 082349872349872 on Friday June 28, 2024 @01:37AM (#40818049)
First boot in the morning was cold, and —the hardware having literally been cold— took minutes longer than subsequent, warm, boots.
Re:A modern 8 bit design, built using 1950s thermionic valves by kazinator on Friday June 28, 2024 @04:12AM (#40818679)
[delayed]
Re:A modern 8 bit design, built using 1950s thermionic valves by 082349872349872 on Friday June 28, 2024 @08:10AM (#40819834)
Maybe I'm misremembering (I was very young) or maybe I was with people who were too superstitious, but these tubes themselves were actually from the 1950s, and they did indeed take a significant amount of time before they decided the hardware was "warm enough" that one could let the software start doing its thing.