Re:After years of trying, the U.S. government may mandate sa...
by avemg on Tuesday April 09, 2024 @10:58AM
(#39980161)
There are LED indicator lights that flash red when it detects a current drop. When the blade is not moving, you can touch it with your finger to see. In theory you could do this with whatever material you're going to cut. If you're cutting metal, it's pretty obvious that you need to disable the brake system. Usually where it's iffy is pressure treated lumber. Sometimes it'll trigger, sometimes not. Really depends on the moisture content of the wood and that can vary greatly. "testing" by touching the material to the blade with your hands on it might or might not indicate that the brake would fire. The points you're contacting could just not be that wet.
Re:After years of trying, the U.S. government may mandate sa...
by vundercind on Tuesday April 09, 2024 @02:14PM
(#39982363)
Most cheap lumber I see these days has a lot of moisture in it, treated or not. I’m surprised this works at all for anything short of quite-nice stock.
Re:After years of trying, the U.S. government may mandate sa...
by rrauenza on Tuesday April 09, 2024 @02:30PM
(#39982555)
Pressure treated wood is also soaked with copper azole, which I believe increases its conductivity.
Re:After years of trying, the U.S. government may mandate sa...
by sidewndr46 on Tuesday April 09, 2024 @02:26PM
(#39982515)
If you manage to cut metal with a table saw, you are a much braver person than I am
Re:After years of trying, the U.S. government may mandate sa...
by UniverseHacker on Tuesday April 09, 2024 @04:30PM
(#39983917)
Aluminum cuts just like wood on a table saw. I wouldn't recommend trying to cut hard metals.
Re:After years of trying, the U.S. government may mandate sa...
by sidewndr46 on Wednesday April 10, 2024 @09:57AM
(#39990809)
With the right blade, I would think that is possible. When a piece of wood kicks back and hits me it leaves a bruise through the clothing I wear. If a piece of aluminum kicks back and hits me, I imagine it would be nearly fatal.
Re:After years of trying, the U.S. government may mandate sa...
by UniverseHacker on Wednesday April 10, 2024 @01:43PM
(#39993585)
I've always just used a regular dull-ish wood blade... never died. Survivorship bias?
Re:After years of trying, the U.S. government may mandate sa...
by avemg on Tuesday April 09, 2024 @08:55PM
(#39985892)
Iron and steel? Of course not, go get a cold saw for that. But it's no problem and very common to cut soft stuff like aluminum and copper on a table saw.
Re:After years of trying, the U.S. government may mandate sa...
by quickthrowman on Tuesday April 09, 2024 @04:19PM
(#39983788)
> Never having used one of these before, is there anything (ideally conveniently built in) that you can use to know before you cut a particular material whether it'll trigger the stop?
You use a $40 “wood moisture meter” to check the water content of the lumber before cutting. If you want a built-in one I suppose you could duct tape it to your saw.
https://www.kleintools.com/catalog/environmental-testers/pin...
Re:After years of trying, the U.S. government may mandate sa...
by garbagewoman on Wednesday April 10, 2024 @08:48AM
(#39990101)
What about some suggestions offered in good faith?
Re:After years of trying, the U.S. government may mandate sa...
by quickthrowman on Wednesday April 10, 2024 @01:46PM
(#39993612)
That is how you measure the moisture content of wood, with a wood moisture meter. There’s no reason for a handheld $40 tool (that any serious woodworker will already have on hand, and one that will likely fail at some point) to be built in to a multiple thousand dollar table saw.
(I think it's unambiguously a good thing to mandate, but I'd also prefer not to have to memorize a table of materials and their interactions with the stopping device...)